AT&T PARTNER CIB 3169 User manual

AT&T
Customer Instruction Booklet:
Partner® Base Unit
CIB 3169
HEADSET BASE UNIT

CIB 3169 Headset Base Unit Guide
This user’s guide contains information on the installation and usage of the AT&T
Headset Base Unit.
Refer to the headset user’s guide for information on the positioning and usage of the
headset.
HEADSET
QUICK
DISCONNECT
PARTNER®
HEADSET
BASE
UNIT
WALL JACK ❑
1❑
3
BRIDGING
ADAPTER
(267F2) PARTNER/MLS SET
❑
2
FIGURE 1
This example shows a PARTNER
®
Plus control unit, but this application can also be used on any PARTNER
System and with any MLS set.
INSTALLATION
■
❑
1
❑
2
❑
3
❑
Connecting the Base Unit to the Telephone (Refer to FIGURE 1)
Unplug the cord from the wall and insert the bridging adapter (267F2).
Insert the cord from the PARTNER set into the lower jack of the bridging adapter.
Insert the cord from the PARTNER Headset Base Unit into the upper jack.
Note: If you are using an 18-Button Set, the RJ11 Jack on the bottom of the set can be
utilized for the Headset Base Unit instead of the 267F2 Bridging Adapter.

FIGURE 2
FIGURE 3
USAGE
■
❑
1
❑
2
❑
3
■
■
❑
1
❑
2
❑
3
Placing and Receiving Calls with the Headset Amplifier
To place a call, activate the headset. You should hear a dial
tone. Dial normally. To end the call, deactivate the headset.
To receive a call, activate the headset. You can now hear
and be heard by the calling party. To end the call, deactivate
the headset.
For handset use, pick up your handset as you would
normally.
Setting the Volume Control
To increase or decrease the volume to the hearing level most
comfortable for you, rotate the volume control. (Refer to
FIGURE 2)
Quick Disconnect
Your headset model is equipped with a Quick Disconnect
module. This feature allows you to place a call on hold
without removing your headset, thus freeing you to perform a
task away from the phone. Your conversation is quickly
resumed by reconnecting the Quick Disconnect.
Before attempting to use your headset, be sure that the two
Quick Disconnect halves are connected.
To put your call on hold, grasp the Quick Disconnect as
shown and pull straight apart. (Refer to FIGURE 3)
To resume your conversation, reconnect the two halves of the
Quick Disconnect.
FCC REGISTRATION INFORMATION
In compliance with FCC Rules and Regulations, Part 68, you are advised that:
1. Before installing your headset, you must notify the owner of the host equipment (i.e.: leasing company).
Provide them with the headset registration number. The number is printed on the headset registration
label.
2.
If the installation of your headset requires the installation of a headset jack/JackSet
®
that connects to
the internal wiring of leased telephones or other devices, such connections can only be made with per-
mission of the owner of the host equipment.
3. In case of trouble, disconnect your headset to determine the trouble source. If the headset is the
source, modifications or repairs can only be made by the headset manufacturer or its authorized repre-
sentative.
LIMITED WARRANTY AND LIMITATION OF LIABILITY
AT&T warrants to you, the customer, that your AT&T telecommunications equipment will be in good
working order on the date AT&T or its authorized reseller delivers or installs the equipment, whichever is
later ("Warranty Date"). If you notify AT&T or its authorized reseller within two years of the Warranty Date
that your equipment is not in good working order, AT&T will without charge to you repair or replace, at its
option, the equipment that is not in good working order. Repair or replacement parts may be new or
refurbished and will be provided on an exchange basis. If AT&T determines that the equipment cannot be

repaired or replaced. AT&T will remove the equipment and, at your option, refund the purchase price of the
equipment, or apply the purchase price towards the purchase of other comparable AT&T equipment.
If you purchased your equipment directly from AT&T, AT&T will perform warranty repair in accordance with
the terms and conditions of the specific AT&T maintenance plan you selected. A written explanation of
AT&T’s maintenance plans may be obtained from AT&T by calling 1 800 247-7000. If you purchased your
equipment from an AT&T authorized reseller, contact your reseller for the details of the maintenance plan
applicable to your system.
AT&T will not be responsible under this limited warranty for damages resulting from:
(1) failure to follow AT&T’s installation, operation, or maintenance instructions;
(2) unauthorized equipment modification, movement or alteration;
(3) unauthorized use of common carrier communication services accessed through the equipment;
(4) abuse, misuse, or negligent acts or omissions of the customer and persons under the customer’s
control; or
(5) acts of third parties and acts of God.
AT&T’S OBLIGATION TO REPAIR, REPLACE OR REFUND AS SET FORTH ABOVE IS YOUR EXCLU-
SIVE REMEDY. THIS WARRANTY IS VOID UNLESS YOUR SYSTEM WAS PURCHASED DIRECTLY
FROM AT&T OR AN AT&T AUTHORIZED RESELLER FOR INSTALLATION IN THE U.S.A. OR PUERTO
RICO.
EXCEPT AS SPECIFICALLY SET FORTH ABOVE, AT&T, ITS AFFILIATES, SUPPLIERS AND AUTHOR-
IZED RESELLERS MAKE NO WARRANTIES, EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM
ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
LIMITATION OF LIABILITY
EXCEPT FOR PERSONAL INJURY OR DAMAGE TO TANGIBLE PERSONAL PROPERTY CAUSED
SOLELY BY AT&T’S NEGLIGENCE, THE LIABILITY OF AT&T, ITS AFFILIATES, SUPPLIERS AND
AUTHORIZED RESELLERS FOR ANY CLAIMS, LOSSES, DAMAGES OR EXPENSES FROM ANY
CAUSE WHATSOEVER (INCLUDING ACTS OR OMISSIONS OF THIRD PARTIES) REGARDLESS OF
THE FORM OF ACTION, WHETHER IN CONTRACT, TORT OR OTHERWISE, SHALL NOT EXCEED AN
AMOUNT EQUAL TO THE LESSER OF THE DIRECT DAMAGES PROVEN OR THE PURCHASE PRICE
OF THE EQUIPMENT. IN NO EVENT SHALL AT&T OR ITS AFFILIATES, SUPPLIERS OR AUTHOR-
IZED RESELLERS BE LIABLE FOR INCIDENTAL, RELIANCE, CONSEQUENTIAL, OR ANY OTHER
INDIRECT LOSS OR DAMAGE (INCLUDING LOST PROFITS OR REVENUES) INCURRED IN CON-
NECTION WITH THE EQUIPMENT. THIS LIMITATION OF LIABILITY SHALL SURVIVE FAILURE OF
THE EXCLUSIVE REMEDY SET FORTH IN THE LIMITED WARRANTY ABOVE.
SERVICE INFORMATION
Should you encounter difficulties or be uncertain about proper installation, please follow the procedures
below:
●
Replace the faulty headset with a working headset. If the problem persists, the problem is
probably not the headset, but in the equipment to which it is connected.
●
If the replacement clears the problem, the trouble is in the headset.
Should your headset fail to operate properly, and you wish to obtain service under the Warranty specified
in your agreement with AT&T, please contact your AT&T representative. When returning the headset for
service, it is not necessary to include the amplifier.
TRADEMARK NOTICES
Partner is a registered trademark of AT&T.
JackSet is a registered trademark of Plantronics, Inc.
PRINTED IN THE U.S.A. 28342-01(©6•93)