ATD Tools ATD-7465 User manual

ATD-7465
VEHICLE POSITIONING JACK
OPERATING INSTRUCTIONS
WARNING!
•Read ALL the instructions and warnings before attempting to operate this jack.
•DO NOT operate jack on inclined surfaces. Jack must be used on level surfaces only.
Unanticipated motion will occur as soon as jack lifts tire from surface.
•DO NOT overload jack beyond the load rating (1500lbs per unit)
•DO NOT start the vehicle’s engine, or drive with jack in use. Jacks are designed for
hand maneuvering of vehicles only.
•DO NOT use jack to lift tires wider than 12 inches.
•DO NOT attempt to push jack over obstacles. They are designed to be used on level
surfaces only.
•After lifting, be sure always lock the pin in place before operating. Pull the pin out
after finishing work and then release the valve.
TO OPERATE:
Place jack on floor and press down on pedal to release pedal lock. Pull out the lock pin from
frame.
Before operating, open release valve by turning hand wheel counter-clockwise. Expand
jack with hand wheel, enough to place around tire and position so both rollers now contact
the tire tread. To obtain the best control of jack while expanding around tire, place your left
hand on top of the left side axle and your right hand at the center of the pedal. Close
release valve by turning hand wheel clockwise to a snug-tight position, jack may now be
used.
IMPORTANT: Install jack so that the unit is parallel to the sidewall of the tire to be lifted.
Leave approximately 3/4” of clearance between tire and jack. If unit is misaligned, it is
possible that the tire will be forced to hit the axle of the jack and not the rollers. This may
damage the jack and will void the warranty.
To lift tire, flip directional lever up and place foot on pedal depressing with smooth, even
strokes. Cycle pedal until tire is lifted about an inch from the surface. The lower the tire is to
the surface the more stable the jack will be. After lifting, be sure to always lock the pin in
place before operating. Repeat this process on the other tires and maneuver the vehicle as
required.
To release jack, pull the pin out from frame and open valve by turning hand-wheel counter
clockwise slowly. Jack may be removed only when rollers are disengaged from the tire.

ITEM# ORDERING PART# PART DESCRIPTION ITEM# ORDERING PART# PART DESCRIPTION
1 PRT7465-01
RAM ASSEMBLY* 11 PRT7465-11 LOCK PIN WITH CHAIN
2 PRT7465-20
BOLT M16X115 12 PRT7465-20 SCREW M6X20 (4 pcs)
3 PRT7465-20
FLAT WASHER
Φ
16 13 PRT7465-20 LOCK WASHER
Φ
6 (4 pcs)
4 PRT7465-20 NUT M16
14 PRT7465-20
FLAT WASHERΦ6 (4 pcs)
5 PRT7465-20
ROLLER RACEWAY (4 pcs) 15 PRT7465-15 RIGHT FRAME
6 PRT7465-06
ROLLER (2 pcs) 16 PRT7465-20 HOOK
7 PRT7465-20 RACEWAY LOCK SCREW (8 pcs)
17 PRT7465-20
WASHER FOR HOOK
8 PRT7465-20 LOCK NUT M12 (4 pcs)
18 PRT7465-20
NUT FOR HOOK
9 PRT7465-09
4” SWIVEL CASTER (4 pcs) 19 PRT7465-19 FOOT PEDAL
10 PRT7465-10
LEFT FRAME 20 PRT7465-20 HARDWARE KIT*
*PRT7465-20 Hardware kit includes items: 2, 3, 4, 5, 7, 8, 12, 13, 14, 16, 17, 18
And is included with PRT7465-01 Ram Assembly
ATD-7465