ATD Tools ATD-7332A Instructions for use

Model: ATD-7332A
Capacity: 3-1/2 Ton
1
ATD-7332A
3-1/2 Ton Hydraulic Service Jack
Capacity Min. Height Max Height Handle
Length
Overall
Length
Overall
Width
Saddle
Diameter
Shipping
Weight
3-1/2 Ton 3-3/4” 21-3/4” 49-1/4” 31-1/8”
Contents:
Page: 1. Speci ca ons
2. Safety & Warning Informa on
3. & 4. Setup, Opera on & Preven ve Maintenance
5. Inspec on, Storage & Troubleshoo ng
6. Exploded View & Replaceable Part Numbers
7. Warranty Informa on
8. Preven ve Maintenance Record Log
Opera ng Instru ons & Parts Manual
14” 4-3/4” 107 LB
ATD7332A_rev_0417
Made in China to ATD Tools, Inc. Specications
Visit us at www.atdtools.com
WARNING: This product may contain chemicals, including lead, known to the State of California
to cause cancer, birth defects or other reproductive harm. Wash hands after handling.

Model: ATD-7332A
Capacity: 3-1/2 Ton
2
SAFETY & WARNING INFORMATION
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
Before opera ng this device, be sure to read all content within this manual, ensuring that you
understand the opera ng procedures, maintenance requirements, and all safety warnings.
The owner and/or operator shall have an understanding of the product, its opera ng
characteris cs, and safety opera ng instruc ons before opera ng this device. Safety
informa on shall be emphasized and understood. If the operator is not uent in English, the
product and safety instruc ons shall be read to and discussed with the operator in the
operator’s na ve language by the purchaser/owner or his designee, making sure that the
operator comprehends their contents.
Actions to help prevent dangerous situations
Study, understand, and follow all instruc ons before opera ng this device.
Do not exceed the rated capacity stated.
Use only on hard level surfaces.
This item is to be used as a li ing device only. Immediately a er li ing, support the vehicle
with appropriate means.
Do not move or dolly the vehicle while it is on the jack.
Li only on areas of the vehicle as speci ed by the vehicle manufacturer.
No altera ons shall be made to this product.
Failure to heed these markings may result in serious personal injury and/or property
damage.
This is the safety n con
symbol. This symbol will n fy you
of any poten al injury hazards.
Please follow all instruc ons that
follow this symbol to avoid possible
injuries or death.
Indicates a hazardous
situa on. If proper steps are
not followed, death or
serious injury could result.

Model: ATD-7332A
Capacity: 3-1/2 Ton
3
SETUP, OPERATION & PREVENTIVE MAINTENANCE
Setup
Prior to each use, visual inspec on (See Pg. 5) shall be made to the device by checking
for abnormal condi ons, such as cracked welds, leaks, and damaged, loose, or missing
parts.
Consult the vehicle owner’s manual to determine the loca on of li points.
Be sure to set the vehicle in park with the emergency brake on and wheels securely
chocked.
Be sure that the vehicle and the jack are on a hard, level surface.
Assembly
If two piece handles are provided, assemble the upper sec on into the lower sec on,
line up the holes, insert and ghten the screw.
Insert the bo om end of handle into handle fork and securely ghten the bolt and
washer. Ensure the handle can turn freely.
Lifting
Turn the handle/release valve clockwise to the closed posi on. Do not over ghten.
Posi on the jack under the speci ed li point.
Begin li ing by pumping the handle up and down.
Immediately a er li ing, support the vehicle with appropriately rated jack stands.
Turn the handle/release valve slowly counterclockwise to lower the vehicle onto jack
stands.
Lowering
Turn the handle/release valve clockwise to the closed posi on. Do not over ghten.
Pump the handle up and down to li vehicle o jack stands.
Remove the jack stands. Do not get under or let anyone get under the vehicle while
lowering.
Turn the handle/release valve slowly counterclockwise to lower the vehicle onto the
ground.
A

Model: ATD-7332A
Capacity: 3-1/2 Ton
4
SETUP, OPERATION & PREVENTIVE MAINTENANCE (Cont.)
Maintenance
NOTICE: Use high grade hydraulic oil only. Never use brake uid, motor oil, transmission uid,
turbine oil or any other uids. ISO-VG22 or equivalent hydraulic oil is recommended.
Check and Refill Oil
With the jack in the fully lowered and in level on, if unit cover is provided, remove unit
cover, then remove oil ller plug.
Proper oil level should be just covering inner cylinder as seen from the oil er plug hole.
Do not over Always ll with new, clean hydraulic jack oil as recommended above.
Reinstall oil r plug, then reinstall unit cover.
Lubrication and Cleaning
Periodically clean and lubricate all moving parts and pivot points.
Air Venting Procedures
With the jack in the fully lowered on, release valve open, remove oil er plug.
Pump the handle rapidly several mes. Reinstall oil er plug.
Turn the handle/release valve clockwise to the closed posi on.
Pump the handle un the li arm reaches maximum height and co nue to pump
several mes to remove trapped air in the system.
Turn the handle/release valve counterclockwise in one full turn and lower arm to the
lowest posi on. Use force on saddle if necessary.
Carefully and slowly loosen oil ler plug to release pressurized air.
Repeat above steps un l trapped air is completely vented.
Damaged Equipment
Any jack that appears to be damaged in any way, is found to be worn, or operates abnormally
SHALL BE REMOVED FROM SERVICE UNTIL REPAIRED. It is recommended that necessary
repairs be made by a manufacturer’s or supplier’s authorized repair facility if repairs are
permi ed by the manufacturer or supplier.
Alterations
Because of poten al hazards associated with this type of equipment, no altera ons shall be
made to the product.
Attachments and Adapters
Only a achments and/or adapters supplied by the manufacturer shall be used.

Model: ATD-7332A
Capacity: 3-1/2 Ton
5
.
INSPECTION, STORAGE & TROUBLESHOOTING
Inspection
Visual inspec on shall be made before each use of the device by checking for abnormal
cons, such as cracked welds, leaks, and damaged, loose, or missing parts.
Other inspec ons shall be made per product opera ng instruc ons.
This device shall be inspected immediately if the device is believed to have been
subjected to an abnormal load or shock. It is recommended that this inspec be made
by a manufacturer’s or supplier’s authorized repair facility.
Owners and/or operators should be aware that repair of this equipment may require
specialized knowledge and es. It is recommended that an annual inspec on of the
product be made by a manufacturer’s or supplier’s authorized repair facility and that
any defec ve parts, decals, or safety labels or signs be replaced with manufacturer’s or
supplier’s speci ed parts.
Storage
This Jack should be stored in a dry loca on on a level surface.
Troubleshooting
Symptom Possible Causes Solu on
Jack will not li the load. 1. Release valve not ghtly closed.
2. Low oil level.
3. Defe ve or worn internal parts.
4. Load exceeds maximum
allowance.
1. Tighten release valve.
2. Check and add oil. Follow “Check
and Oil” instru ns on Pg.4.
3. Disc nue use and contact a
local repair center.
4. Use a higher capacity jack.
Jack will not hold the load. 1. Release valve not ghtly closed.
2. Power unit malfunc on.
1. Tighten release valve.
2. Disc nue use and contact a
local repair center.
Jack will not descend to
minimum height, or will not
remain in lowered posi on.
1. Air trapped in system.
2. Reservoir oil over lled.
1. Vent air out of system. Follow “Air
Ve ng Procedures” above.
2. Check and ensure proper oil level.
Follow “Check and Oil”
instru n on Pg.4.
Jack will not li to max
height.
1. Low oil level. 1. Check and ensure proper oil level.
Follow “Check and Oil”
instruc ns on Pg. 4.
Jack will not fu on
properly a er tried solu n.
1. Internal malfunc on or structural
damage.
1. Stop usage and contact an
authorized repair center.

Model: ATD-7332A
Capacity: 3-1/2 Ton
6
EXPLODED VIEW & REPLACEABLE PART NUMBERS
* Items not iden ed by part number are not available for replacement.
1
2
11
9
8
7
6
3
4
10
5
Item Part Number* Descrip on Q’ty
1LYD3G-100 Front wheel assembly 2
21dap/welddaSA005-G3DYL
3GB308-84-#6 Grease Fi 1gn
41revoC3-J3DYL
5
LYDBI-3T-17
Handle Assembly w/ foam 1
62gnirpSnruteRA9-2DYL
7LYDBI-3T.4 Power Unit Assembly 1
8LYD3G-300 Handle Fork Assembly 1
9LYD3G-400 Rear Caster Assembly 2
10
LYD3F-102A
Handle foam only 1
11 LYD3K-1 Saddle pad only 1
N/A 1lebaLtcudorPL-A2337DTA

7
WARRANTY INFORMATION
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from your purchase date, ATD Tools Inc. will repair or
replace (at its option) without charge, your ATD product if it was purchased new and the product
has failed due to a defect in material or workmanship which you experienced during normal use
of the product. This limited warranty is your exclusive remedy.
To access the benefits of this warranty, contact your ATD Tools, Inc. supplier for confirmation
that this warranty applies. Thereafter, you may be advised to return the product under warranty,
freight prepaid, to the ATD service department.
If this ATD product is altered, abused, misused, modified, or undergoes service by an
unauthorized technician, your warranty will be void. We are not responsible for damage to
ornamental designs you place on this ATD product and such ornamentation should not cover
any warnings or instructions or they may void the warranty. This warranty does not cover
scratches, superficial dents, and other abrasions to the paint finish that occur under normal use.
Subject to the law in your state:
(1) Your sole and exclusive remedy is repair or replacement of the defective product as
described above.
(2) ATD is not liable for any incidental damages, including but not limited to, lost profits and
unforeseeable consequences.
(3) The repair and replacement of this product under the express limited warranty described
above is your exclusive remedy and is provided in lieu of all other warranties, express or
implied. All other warranties, including implied warranties and warranties of
merchantability or fitness for a particular purpose are disclaimed and, if disclaimer is
prohibited, these warranties are limited to one year from your date of purchase of this
product.
Some states’ laws do not allow limited durations on certain implied warranties and some states’
laws do not allow limitations on incidental or consequential damages. You should consult the
law in your state to determine how your rights may vary.
Model: ATD-7332A
Capacity: 3-1/2 Ton
Made in China to ATD Tools, Inc. Specifications
Visit us at www.atdtools.com
Warranty Service Number 1-844-364-9922
For Non-warranty issues, please contact your supplier.
Printed In China

Model: ATD-7332A
Capacity: 3-1/2 Ton
8
PREVENTIVE MAINTENANCE RECORD LOG
Date Maintenance Performed