Atlantic Furniture WINDSOR BUNK BED User manual

Size of Mattress and Foundation
The length and width of the upper bunk mattress and foundation are as follows :
Width
37½”-38½”
Length
74”- 75”
Thickness
9 ½” max
You must use only this size mattress.
Ensure thickness of mattress and foundation combined does not exceed 9 ½”
and that the mattress is at least 5” below upper edge of guardrails.
This Bunk Bed uses a slat kit for mattress foundation.
Replacement Parts
Replacement parts, including additional guardrails, may be obtained from any
Atlantic Furniture dealer
SAFETY WARNINGS
! !
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
Follow the information on the warnings appearing on the upper bunk end structure
and on the carton. Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both,
to help prevent the likehood of entrapment or falls.
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other component are
in their proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed, and prohibit jumping on the bed.
Always use ladder for entering or leaving upper bunk.
Do not use substitute parts. Contact the manufacturer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to a wall, the guardrail that runs the full length of the bed must be placed
against the wall to prevent entrapment between the bed and the wall.
The use of water or sleep flotation mattress is prohibited.
Prohibit more than one person on upper bunk.
STRANGULATION HAZARD : Never attach or hang items to any part of the Bunk Bed
that are not designed for use with the bed: for example, but not limited to, hooks, belts
and jump ropes.
Keep these instructions for future reference.
Page1of7
BUNK SAVETY WARNING 09292009

READY
ASSEMBLY INSTRUCTIONSASSEMBLY INSTRUCTIONS
Before assembling your Windsor bunk bed, please read through these
instructions carefully, familiarising yourself with the different parts.
WINDSOR BUNK BED
Thank you for choosing our new bunk bed.
This practical design offers the utmost in versatility.
HARDWARE
Please note that you will require a Phillips head screwdriver and an Allen wrench (provided).
Assembling by Adult
Allen wrench
Phillips head
Customer Supplied
screwdriver
BUNK BED SHOWN WITHOUT LADDER
Page2of7
AJCB M6 X 4” - 16 pcs
Fix Panel to Long Rail ( upper + lower )
BFix End Cap to Guard Rail
JCB M6 X 2” - 4 pcs
CBarrel Nut - 20 pcs
Fix End Cap to upper Long Rail
1 ” Wood Screw-4pcs
E
E
FAllen wrench-1pc
E
D
Metal Pins-4pcs
WINDSOR BUNK BED 09292009

PARTS LIST
01
02
03
04
05
06
07
08
HARDWARE
UPPER PANEL BOX 1 of 4
BOX2of4
BOX 4 of 4 2 SET
BOX3of4
LOWER PANEL
FULL GUARDRAIL
3/4 GUARDRAIL
END CAPS (Left + Right)
LONG RAILS
TWIN SLAT KIT
01
02
03
06
07
07
08
07
07
06
06
06
04
08
05
02
03
Page3of7
WINDSOR BUNK BED 09292009

A
STEP 1
STEP 2
07
07
C
C
C
A
B
B
B
B
F
F
Attach the long rails (07) to the upper panels (02), using JCB M6 X 4” (A),
and barrel nut (C). Tighten with the Allen wrench (F).
Attach the full guard rail (04) to the end caps (06), using JCB M6 X 2” (B),
and barrel nut (C). Tighten with the Allen wrench (F).
Repeat for 3/4 guard rail (05).
If the bunk bed will be placed next to a wall, the guard rail that runs the full length
of the bed should be placed against the wall to prevent entrapment
between the bed and the wall.
Note : Screw holes on end caps go on inside of guard rails.
07
A
C
F
Assembling by Adult
JCB M6 X 4”
Barrel Nut
Allen wrench
B
C
F
Assembling by Adult
JCBM6X2”
Barrel Nut
Allen wrench
06
06
06
06
C
C
C
02
04
05
C
C
C
A
F
A
02
Page4of7
WINDSOR BUNK BED 09292009

Lay the twin slat kit (08) onto the bed. Fix in place using wood screws provided in the slat kit box.
FOR SLAT KIT ASSEMBLY follow assembly instructions included with slat kit.
Install the full and 3/4 guard rail assemblies onto the long rails, and fix in place using wood screws (D).
Tighten with the Phillips head screwdriver.
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
08
D
D
D
FULL GUARD RAIL
ASSEMBLY
3/4 GUARD RAIL
ASSEMBLY
D
D
Assembling by Adult
1 “ Wood Screw
D
Phillips head
Customer Supplied
screwdriver
Assembling by Adult
Phillips head
Customer Supplied
screwdriver
Page5of7
WINDSOR BUNK BED
STEP 3
STEP 4
09292009

A
STEP 5
STEP 6
A
C
F
Assembling by Adult
JCB M6 X 4”
Barrel Nut
Allen wrench
07
07
A
C
C
Attach the long rails (07) to the lower panel (03), using JCB M6 X 4” (A),
and barrel nut (C). Tighten with the Allen wrench (F).
07
C
Lay the twin slat kit (08) onto the bed, and fix in place using wood screws
provided in the slat kit box. FOR SLAT KIT ASSEMBLY follow
assembly instructions included with slat kit.
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
08
03
Assembling by Adult
Phillips head
Customer Supplied
screwdriver
C
A
C
A
F
03
Page6of7
WINDSOR BUNK BED 09292009

STEP 7
STEP 8
E
E
E
Assembling by Adult
Metal Pins
E
Insert metal pins (E) into the holes in top of the lower panels.
Lift the upper panels onto the lower panels as shown, and fit the metal
pins into the holes in the bottom of the upper panel legs.
This step requires
two strong people.
This step requires
two strong people.
CAUTION
!
Congratulations !
Your Windsor bunk bed is now ready for use.
We recommend that you recheck that all screws are tightened,
and that all parts are secure before use and periodically to ensure safety.
Assembling by Adult
Phillips head
Customer Supplied
screwdriver
E
FOR LADDER ASSEMBLY, PLEASE
FOLLOW ASSEMBLY INSTRUCTIONS
INCLUDED WITH YOUR LADDER.
Lastly, install Ladder.
Page7of7
WINDSOR BUNK BED 09292009