Atlantic Ultraviolet Sanidyne Prime 40-0633A User manual

1
Document No. 98-1692B5 • May 2020 • ©2020 Atlantic Ultraviolet Corporation®
8 High Output
UV Lamps with
ArmorLite™
Lamp Safety
Shield
Models
40-0633A (120v)
40-0673A (230v)
Owner’
s Manual
Owner’
s Manual
Installation,
Operation &
Maintenance
Read and Follow All
Safety Instructions.
Save These Instructions.
UV
Ultraviolet
Radiation
Protect eyes and
skin from direct and
reflected radiation.
DANGER
!
Extensive Product Information Available at:
Ultraviolet.com
Buyultraviolet.com

2
TABLE OF CONTENTS
SAFETY WARNINGS ....................................................................................................................................................................... 3
SAFETY INSTRUCTIONS .............................................................................................................................................................. 3
SAFETY LABELS .........................................................................................................................................................................4–5
CAUTION........................................................................................................................................................................................... 4
PRODUCT APPLICATIONS ........................................................................................................................................................... 6
ConstruCtion ..................................................................................................................................................................................................... 6
PrinCiPle of oPeration ..................................................................................................................................................................................... 6
limitations .......................................................................................................................................................................................................... 6
UNPACKING ..................................................................................................................................................................................... 7
INSTALLATION ............................................................................................................................................................................... 7
Dimensional Data...........................................................................................................................................................................7
unit PlaCement ..............................................................................................................................................................................8
lamP installation .......................................................................................................................................................................... 8
SANIDYNE®PRIME OPERATION................................................................................................................................................ 9
KeyPaD Controller overview .......................................................................................................................................................9
using the KeyPaD Controller to set treatment times ...............................................................................................................9
testing unit oPeration............................................................................................................................................................9–10
Determining treatment time.......................................................................................................................................................10
treatment CyCle.......................................................................................................................................................................... 11
MAINTENANCE............................................................................................................................................................................. 11
maintenanCe overview ................................................................................................................................................................ 11
lamP installation, rePlaCement, or Cleaning ..................................................................................................................... 11–12
BreaKage ......................................................................................................................................................................................12
DisPosal of merCury aDDeD lamP ..............................................................................................................................................12
TROUBLESHOOTING ..................................................................................................................................................................12
fuse rePlaCement ........................................................................................................................................................................13
TECHNICAL SPECIFICATIONS................................................................................................................................................. 13
OPTIONAL ACCESSORIES .........................................................................................................................................................14
REPLACEMENT PARTS............................................................................................................................................................... 14
MAINTENANCE LOG...................................................................................................................................................................15
USER ASSISTANCE ....................................................................................................................................................................... 16
Patent notiCe...............................................................................................................................................................................16
WARRANTY & PRODUCT REGISTRATION ...........................................................................................................................16
These instructions generally describe the installation, operation and maintenance of the Sanidyne®Prime Portable Area
Sanitizer. Questions that are not specically answerable by these instructions should be directed to the factory.
Atlantic Ultraviolet Corporation® takes all possible precautions when packaging equipment to prevent damage.
Carefully inspect and report all damages. Do not install damaged equipment.
Follow all instructions on any labels or tags. Carefully inspect all packing materials before discarding to prevent the loss of
accessories, mounting hardware, spare parts or instructions.
The information and recommendations contained in this publication are based
upon data collected by the Atlantic Ultraviolet Corporation®and are believed to
be correct. However, no guarantee or warranty of any kind, expressed or implied,
is made with respect to the information contained herein. Specications and
information are subject to change without notice.

3
To guard against injury, basic safety precautions should be observed, including the following:
1. Read and follow ALL safety instructions.
2. Avoid exposure to direct or reected germicidal ultraviolet rays. Germicidal
ultraviolet rays are harmful to the eyes and skin.
3. Intended for indoor use only.
4. Do not alter design or construction.
5. Do not use this sanitizer for other than its intended purpose, as described in this manual.
6. Do not use this sanitizer in occupied areas. The supplied “DANGER - DO NOT ENTER…” sign(s) MUST be clearly
displayed to warn against entering the area during the disinfection cycle without proper personal protection equipment.
7. Germicidal ultraviolet rays may break down plastic, rubber or other non-metallic materials, with inadequate
resistance to ultraviolet. Shield all plastic, rubber or other non-metallic parts which may be exposed to direct or reected
germicidal ultraviolet rays.
8. Do not remove any labels.
9. Do not operate without proper electrical ground.
10. Do not operate the sanitizer if the power cord and/or plug are damaged, or if any other damage to the sanitizer is
visible or suspected.
11. Utility power supplied, to the sanitizer MUST match power requirements listed on the sanitizer label.
12. Always disconnect power to the xture before performing any service or maintenance.
13. Read and follow all notices and warnings on the sanitizer.
14. SAVE THESE INSTRUCTIONS.
SAFETY INSTRUCTIONS
SAFETY WARNINGS
• All personnel should be alerted to the potential hazards indicated by the product safety labeling on this unit.
• The following conventions are used to indicate and classify precautions in this manual and on product safety labeling. Failure to
observe precautions could result in injury to people or damage to property.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
This symbol is used to identify the need to wear
protective gloves.
!
Caution indicates a POTENTIALLY
hazardous situation, which, if not avoided,
MAY result in minor or moderate injury.
Caution used without the safety alert symbol
indicates a potentially hazardous situation, which,
if not avoided, may result in property damage.
Warning indicates a POTENTIALLY
hazardous situation, which, if not avoided,
COULD result in death or serious injury.
This symbol is used to identify an
ULTRAVIOLET LIGHT hazard.
This symbol is used to identify an ELECTRICAL
SHOCK or ELECTROCUTION hazard.
This symbol is used to identify the need to wear
approved ultraviolet blocking eyewear.
This symbol is used to identify the need to wear approved
ultraviolet blocking face shield.
This symbol is used to identify components which must
not be disposed of in trash
Danger indicates an IMMINENTLY
hazardous situation, which, if not avoided,
WILL result in death or serious injury.

4
SAFETY LABELS
Safety Label: Warning:
Ultraviolet Radiation (70-0052)
Safety Label: Danger:
Hazardous Voltage (00-0197A2)
Location of Safety Label (70-0052)
Location of Safety Labels (00-0197A2 and 70-0011)
Location of Safety Label (70-0038) on Both Sides of Unit
CAUTION
It is the user’s responsibility to determine and validate the suitability of this equipment for use in the user’s system or
process. No warranty or representation is made by the manufacturer with respect to suitability or performance of this
equipment or to the results that may be expected from its use. The user should periodically inspect, clean as necessary and
conrm the presence and good legibility of the product safety labels. Contact the factory for replacement labels in the event
that any of the labels are missing or illegible.
Hg-Lamp Contains Mercury Label (70-0011)
Safety Label: Danger: Hazardous Voltage /
Ultraviolet Radiation (70-0038)

5
SAFETY LABELS
(2) Promate™Laminated Danger
Signs (00-0098 / 00-0456) Front in
English, back in Spanish 8.5”x11”.
(1) Promate™ Laminated Danger Sign (98-1803 / 98-1804)
Front in English, back in Spanish, 8.5”x11” with slits to
mount on Sanidyne®Prime Protected Cover.
(2) Danger Label: Ultraviolet
Radiation Spanish (70-0060)
(2) Danger Label: Ultraviolet
Radiation English (00-0358)
Location of Danger Label (00-0358) on Both Sides of Cover
The Sanidyne®Prime Protective Cover should be used to hold Danger
Signs and additional Danger Labels. Place Protective Cover in location
blocking entrance to area being sanitized, as shown below.
Location of Sanidyne®Prime
Protective Cover during sanitization.
ULTRAVIOLET DISINFECTION
IN PROGRESS
DO NOT ENTER
DANGER
!
ULTRAVIOLET RAYS ARE
HARMFUL TO EYES AND SKIN
00-0098
Front
ULTRAVIOLET DISINFECTION
IN PROGRESS
DO NOT ENTER
DANGER
!
ULTRAVIOLET RAYS ARE
HARMFUL TO EYES AND SKIN
00-0098
Front
ULTRAVIOLET DISINFECTION
IN PROGRESS
DO NOT ENTER
DANGER
!
ULTRAVIOLET RAYS ARE
HARMFUL TO EYES AND SKIN
98-1803
Front
NO ENTRE
DESINFECCION ULTRAVIOLETA
EN PROGRESO
RAYOS ULTRAVIOLETA SON
NOCIVOS PARA LOS OJOS Y PIEL
PELIGRO
00-0456
Back
NO ENTRE
DESINFECCION ULTRAVIOLETA
EN PROGRESO
RAYOS ULTRAVIOLETA SON
NOCIVOS PARA LOS OJOS Y PIEL
PELIGRO
00-0456
Back
NO ENTRE
DESINFECCION ULTRAVIOLETA
EN PROGRESO
RAYOS ULTRAVIOLETA SON
NOCIVOS PARA LOS OJOS Y PIEL
PELIGRO
98-1804
Back
DANGER
!
UV
Ultraviolet
Radiation
Protect eyes and
skin from direct and
reflected radiation.
Part No. 00-0358
Danger: UV 5”x5” PMS109, PMS185/ out dr & Bk White Mylar UV Varnish
00-0358
PELIGRO
!
UV
Radiación
Ultravioleta
Proteger los ojos y
la piel de la radiación
directa y reflejada.
Part No. 00-0358
Danger: UV 5”x5” PMS109, PMS185/ out dr & Bk White Mylar UV Varnish
70-0060
ULTRAVIOLET DISINFECTION
IN PROGRESS
DO NOT ENTER
DANGER
ULTRAVIOLET RAYS ARE
HARMFUL TO EYES AND SKIN
70-0059
NO ENTRE
DESINFECCION ULTRAVIOLETA
EN PROGRESO
RAYOS ULTRAVIOLETA SON
NOCIVOS PARA LOS OJOS Y PIEL
PELIGRO
70-0059
ULTRAVIOLET DISINFECTION
IN PROGRESS
DO NOT ENTER
DANGER
ULTRAVIOLET RAYS ARE
HARMFUL TO EYES AND SKIN
70-0059
NO ENTRE
DESINFECCION ULTRAVIOLETA
EN PROGRESO
RAYOS ULTRAVIOLETA SON
NOCIVOS PARA LOS OJOS Y PIEL
PELIGRO
70-0059
(4) Danger Labels (70-0059) 2-English,
2-Spanish, 5.5” x 4.25”. English applied to
cover; Spanish attached to this Safety Label
page in this Manual for use by operator.
ULTRAVIOLET DISINFECTION
IN PROGRESS
DO NOT ENTER
DANGER
ULTRAVIOLET RAYS ARE
HARMFUL TO EYES AND SKIN
70-0059
NO ENTRE
DESINFECCION ULTRAVIOLETA
EN PROGRESO
RAYOS ULTRAVIOLETA SON
NOCIVOS PARA LOS OJOS Y PIEL
PELIGRO
70-0059
ULTRAVIOLET DISINFECTION
IN PROGRESS
DO NOT ENTER
DANGER
ULTRAVIOLET RAYS ARE
HARMFUL TO EYES AND SKIN
70-0059
NO ENTRE
DESINFECCION ULTRAVIOLETA
EN PROGRESO
RAYOS ULTRAVIOLETA SON
NOCIVOS PARA LOS OJOS Y PIEL
PELIGRO
70-0059
English label applied to cover; Spanish label attached to this
Safety Label page in this manual for use by operator.
ULTRAVIOLET DISINFECTION
IN PROGRESS
DO NOT ENTER
DANGER
ULTRAVIOLET RAYSARE
HARMFUL TO EYES AND SKIN
70-0059
NO ENTRE
DESINFECCION ULTRAVIOLETA
EN PROGRESO
RAYOS ULTRAVIOLETA SON
NOCIVOS PARA LOS OJOS Y PIEL
PELIGRO
70-0059
ULTRAVIOLET DISINFECTION
IN PROGRESS
DO NOT ENTER
DANGER
ULTRAVIOLET RAYSARE
HARMFUL TO EYES AND SKIN
70-0059
NO ENTRE
DESINFECCION ULTRAVIOLETA
EN PROGRESO
RAYOS ULTRAVIOLETA SON
NOCIVOS PARA LOS OJOS Y PIEL
PELIGRO
70-0059

6
PRODUCT APPLICATIONS
ConstruCtion
The Sanidyne®Prime Portable Area Sanitizer consists of:
• STER-L-RAY ®Germicidal Ultraviolet Lamps: Deliver ultraviolet energy at the specic wavelength of 254 nanometers (nm).
This wavelength is highly effective against microbes including: virus, bacteria, and mold spores.
• Timer: A microprocessor controller provides easily programmable treatment times in minutes and hours (up to 24 hours), to suit
a variety of room sizes.
• Audible Exit Warning: Provides an audible warning for 1 minute and 30 seconds after the start button is pushed, allowing the
operator time to leave the area before the disinfection cycle begins.
• Elapsed Time Indicator: A non-resettable display of the operating hours. Useful for scheduling and recording maintenance and
lamp replacement.
• Power Cord: For 120v AC 50/60Hz single-phase standard household current, a NEMA 5-15, three-prong plug is provided for a
properly grounded outlet. 230v AC 50/60Hz models use a CEE 7/7 (Schuko type) plug. Consult factory for alternate plug types.
• Storage Cover: Protects the germicidal lamps from breakage while transporting and/or storing the sanitizer and provides a way
to safely test the ultraviolet lamp operation.
• Sight Ports: Located on the top cover, allow observation of the germicidal lamps without the risk of ultraviolet exposure when
the storage cover is on.
• Stainless Steel Lamp Guard Assembly: Protects lamps from damage during normal operation.
• Stainless Steel Construction: All electronics and wiring are housed in an enclosure constructed of stainless steel. Stainless steel
construction provides strength, durability and will withstand most harsh environments.
• Sanidyne®Prime will operate between 120v 50/60Hz and 250v 50/60Hz.
PrinCiPle of oPeration
The Sanidyne®Prime design has been carefully conceived to provide direct germicidal ultraviolet exposure for air and surface
disinfection in unoccupied space to disinfect and prevent areas and surfaces from microorganisms. The ultraviolet disinfection
dosage is a function of time and the intensity, of the ultraviolet radiation to which the air and surrounding surfaces are exposed.
Note that the Sanidyne®Prime should be used as a supplement to your facility’s cleaning and disinfection protocols, not as a
replacement. Follow your facilities cleaning and disinfection protocols before using the Sanidyne®Prime.
No special room preparation is required prior to treating a room or area with the Sanidyne®Prime; however, target surfaces
must be directly exposed to the UV rays. These rays will not penetrate materials like cloth, paper or ordinary glass, therefore,
it is important to remove items from the direct line of sight that would block or shield the rays from other surfaces. The Sanidyne®
Prime does not generate any harmful byproducts, nor does it leave any residual substances.
It is the user’s responsibility to determine and validate the suitability of the equipment for use in system or
process. No warranty or representation is made by the manufacturer with respect to suitability or performance of this
equipment or to the results that may be expected from its use.
Indoor Use Only – The equipment must be sheltered from exposure to the elements and extremes in
temperature. Temperature range: 40°F to 95°F. The user should periodically inspect, clean as necessary and conrm the
presence and good legibility of the Product safety labels. Contact the factory for replacement labels in the event that any of
the labeling is missing or illegible.
The UV Treatment Results achieved are subject to variations in application conditions, it is recommended
that culture tests be performed to conrm desired outcomes.
limitations
• Safety procedures MUST be implemented to prevent ultraviolet exposure of occupants to direct or reected ultraviolet rays.
Exposure to germicidal ultraviolet rays will result in the irritation of the eyes and reddening of the skin.
• Personal protection equipment is required when entering the irradiated space with the germicidal
lamp(s) operating. Personal protection equipment includes skin and eye protection such as gloves,
long sleeves with no gaps between cuff and gloves, and an ultraviolet blocking face shield (included
with the purchase of the Sanidyne®Prime).

7
UNPACKING
IN ORDER TO PERFORM THIS TASK, BE SURE TO WEAR THE FOLLOWING SAFETY
EQUIPMENT: SAFETY GLASSES OR A FACE SHIELD, AS WELL AS GLOVES.
• Remove the Sanidyne®Prime from its shipping carton.
• Atlantic Ultraviolet Corporation® takes all possible precautions when packaging this xture to prevent damage. Carefully
inspect the unit, power cord and plug for damage, report all damage immediately. Do not assemble or operate if there is
any damage, visible or suspected.
• STER-L-RAY ®Germicidal Lamps are packed separately to ensure maximum protection. Keep the lamps aside until
ready for installation.
• Carefully inspect all packing materials to prevent the loss of accessories, spare parts or instructions.
• Do not discard packing materials until sanitizer is assembled and proper operation is conrmed.
The Sanidyne®Prime Portable Area Sanitizer includes:
• 1 - Eight-lamp xture with power cord - Includes a microprocessor controller with a time display and push button controls.
• 8 - STER-L-RAY ®Germicidal Ultraviolet Lamps (Item #05-0892)
• 1 - PromateTM Ultraviolet-Blocking Face Shield with Adjustable Headgear
• 1 - Owner’s Manual
• 2 - PromateTM Laminated Danger Signs (1 Side English /1 Side Spanish)
1 - PromateTM Laminated Danger Signs with Slits (1 Side English /1 Side Spanish)
• 4 - Danger Labels (English applied/Spanish attached to Safety Label page in Manual)
2 - Danger UV Radiation Labels (English applied / Spanish attached to Safety Label page in Manual)
• 1 - Storage Cover
INSTALLATION
Dimensional Data
Figure 1 – Dimensional Data
All specications, dimensional data, etc are approximate and subject to change without notice.

8
lamP installation
IN ORDER TO PERFORM THIS TASK, BE SURE TO WEAR THE FOLLOWING SAFETY
EQUIPMENT: SAFETY GLASSES OR A FACE SHIELD, AS WELL AS GLOVES.
Germicidal lamps are easily damaged. Exercise care when handling lamps.
Always disconnect power to the xture before performing any service or maintenance.
1. Remove protective storage cover
by releasing the three latches on the
storage cover.
2. Remove the top cover after loosening
the four thumbscrews.
3. Holding the lamp vertically by the
pinless base, align the connector pins
on the lamp base with the socket below.
4. Carefully insert the lamp into the socket.
5. Carefully snap lamp into the lamp guide
located on the lamp guard assembly.
6. Install the remaining seven lamps as
described in steps 3, 4, and 5.
7. Re-install the top cover and tighten the
four thumbscrews.
8. Replace the storage cover and secure
using the three latches.
Always Disconnect Power to the
Sanidyne®Prime
Step 1 – Release Latches Step 2 – Loosen Four Thumbscrews
Step 3 – Hold Lamp by Pinless
Base & Align Connector Pins
with Socket Below
Step 4 – Insert Lamp into Socket
Step 5 – Snap into Lamp Guide
unit PlaCement
• The Sanidyne®Prime Portable Area Sanitizer does not require professional installation.
• The Sanidyne®Prime is intended for use in UNOCCUPIED AREAS ONLY. Under no circumstances
should this sanitizer be permitted to operate with humans, plants, or animals present in the Operation Area.
• Electrical power supplied to the Sanidyne®Prime must match power requirements listed on the unit.
• The Sanidyne®Prime is intended for indoor use only. The Sanidyne®Prime should be protected from liquid intrusion such
as dripping water, condensation, or mist, and used only in a clean, dry location with temperature ranges between 40°F to 95°F.
• For maximum efciency, the Sanidyne®Prime should be located as centrally as possible, away from the corners of the
treatment area. The Sanidyne®Prime Portable Area Sanitizer is most effective when it is located in the center of the room
and the ultraviolet rays are unobstructed.
• Access to the room MUST be avoided while the Sanidyne®Prime is operating.

9
SANIDYNE ®PRIME OPERATION
KeyPaD Controller overview
Figure 2 – Timer Conguration
1. Treatment Time: Displays chosen treatment time which will countdown after start is selected. Flashes with word “PREP”
during Countdown Time, the word “RUN” during Treatment Time and “DONE” when Treatment Time is completed.
2. Hour Buttons: Up and down buttons are used to select treatment hours between 0 and 24.
3. Minute Buttons: Up and down buttons are used to select treatment minutes between 0 and 59.
4. Start Button: Begins treatment time countdown.
5. Power Indicator: Glows RED when power is applied to unit and will ash during Treatment Time.
using the KeyPaD Controller to set treatment times
1. Treatment time on the Sanidyne®Prime is controlled by the Keypad Controller (Shown in Figure 2).
1. Setting Treatment Time on the Keypad is done using the HOURS and MINUTES buttons which are located on the front of
the unit. (See Figure 2 for location) Selecting the up or down facing arrows located on the keypad in line with the HOURS
or MINUTES button will either increase or decrease the hours or minutes. The hours can be set between 0 and 24, and the
minutes can be set from 1 to 59. (Example of one hour and ve minutes would appear as 01:05 on the Treatment Time Display).
2. Determining the proper treatment times for your specic location can be done by using the “Recommended Treatment Time
for Room Size” chart (Figure 3 on Page 10).
3. Once the choice of time has been displayed on the Keypad Controller, select the START button to begin and leave the
Operation Area immediately.
Once you select the START button an audible exit alarm will begin to sound and the Sanidyne®Prime will begin counting
down from 1:30 seconds to allow all inhabitants to leave the area before the UV treatment begins. Additionally the word
“PREP” will begin ashing on the Keypad.
Under no circumstances should this sanitizer be permitted to operate with humans or animals present in
the Operation Area. DO NOT return to the Operation Area until the set treatment time has expired.
testing unit oPeration
IN ORDER TO PERFORM THIS TASK, WEAR PERSONAL PROTECTION EQUIPMENT; GLOVES,
LONG SLEEVE SHIRT WITH NO GAPS BETWEEN CUFFS AND GLOVES, AND AN ULTRAVIOLET
BLOCKING FACE SHIELD MUST BE WORN TO COVER AND PROTECT EYES AND EXPOSED SKIN.
1. Conrm cover is installed and 3 latches engaged. Although the cover must be tted before testing the Sanidyne®Prime, the
operator must also put on the safety face shield as an extra precaution.
2. Connect the power cord, plug into appropriate power source.
3. Turn power on using the Power Switch located on the rear of the Sanidyne®Prime (See Power Switch location shown on
Figure 1 - View C-C). Switch will glow RED when power is on. The POWER indicator located on Keypad Controller should
also illuminate.
4. Use the HOURS and MINUTES buttons to set the treatment time to display a short time, such as 00:02 (2 minutes).
5. Press the START button. The audible alarm will beep. (Continued on Page 10)

10
Determining treatment time
The Sanidyne®Prime is intended for use in UNOCCUPIED AREAS ONLY. Under no circumstances
should this unit be permitted to operate with humans, plants or animals present in the Operation Area. Consult our UV
Application Specialists if you have any questions or need help with the Sanidyne®Prime.
1. The xture should be located in the approximate center of the room and target surfaces must be directly exposed to the
ultraviolet rays. It is important to remove items from direct line of sight that would block or shield UV rays from striking target
surfaces. Depending on the conguration of the space, and what specic disinfection you are looking to achieve, it may be
advisable to operate the Sanidyne®Prime on each side of large xed objects (like a bed, or table, etc).
2. Measure the longest distance from the Sanidyne®Prime to the farthest wall. Use this length to compare to the Distance From
Fixtures / Time (Minutes) shown on Figure 3 below.
3. For example, if the distance from your xture measures 15 feet, nd the 15 foot mark on the bar chart for each time range.
As the treatment time increase, dose increases. (NOTE: The number at the end of each bar is the expected dose for each time
increment in millijoules per square centimeter.)
4. If a greater dose is required, increase treatment time.
Figure 3 – Recommended Treatment Time for Room Sizes - Sanidyne®Prime
NOTE: Dose shown above is expressed as mJ/cm2 (millijoule per square centimeter).
23.796
19.830
35.265
79.365
15.864
28.212
63.492
11.898
21.15 9
47.619
7.932
14.10 6
31.746
3.966
7.053
15.873
42.318
95.238
5
10
15
20
Time (Minutes)
Dose (mJ/cm2)
25
30
10.0 Foot 15.0 Foot 20.0 Foot
Distance From Fixture
6. Press the START button again to pause the exit warning. Conrm that the beeping stops.
7. Press the START button again to restart the exit time.
8. At the end of the 1-minute, 30-second exit time, the audible alarm will stop and the POWER indicator light will start ashing.
9. The STER-L-RAY ®Germicidal Lamps should then switch on for the time set in the digital treatment time display.
10. Ensure that all eight STER-L-RAY ®Germicidal Lamps are lit through the sight ports in top cover and that lamps remain on
for the time set on the digital display.
11. The power plug may be removed when treatment is nished.
12. Keep the protective storage cover in place when the Sanidyne®Prime is not in use