Atmel SMART ATBTLC1000 User manual

ATBTLC1000 BluSDK
Phone Alert Status Profile - Getting Started Guide
USER GUIDE
Introduction
This getting started guide describes the setup of the Atmel®ATBTLC1000 with a supported platform
bringing-up an example profile supplied as part of BluSDK release. The Bluetooth®Phone Alert Status
Profile is an example application that is embedded as part of the software release package.
The Phone Alert Status profile (PAS) is used to obtain the Phone Alert Status exposed by the Phone Alert
Status service on a mobile device. Alert Status and Ringer Setting information of a mobile phone can be
received and modified by the Phone Alert Status service. The device can also use this profile to configure
ringer status on the mobile device.
This document explains the details about:
1. Getting started with the setup of supported platform to be used as a Phone Alert Client.
2. Getting the Phone Alert Status Application working on the above mentioned setup.
Features
Device Discovery and Disconnection
Pairing / Bonding
Phone Alert Status Alerts
Console Display
Atmel-42547C-ATBTLC1000-BluSDK-Phone-Alert-Status-Profile-Getting-Started-Guide_UserGuide_022016

ATBTLC1000 BluSDK Phone Alert Status–Getting Started Guide [USER GUIDE]
Atmel-42547C-ATBTLC1000-BluSDK-Phone-Alert-Status-Profile-Getting-Started-Guide_UserGuide_022016
2
2
Table of Contents
1Demo Setup..................................................................................................................3
2Supported Hardware Platforms and IDEs ..................................................................3
3Hardware Setup ...........................................................................................................4
3.1 SAM L21 Xplained Pro Phone Alert Status Client Setup.......................................................................4
3.2 SAM D21 Xplained Pro Phone Alert Status Client Setup ......................................................................4
3.3 SAM G55 Xplained Pro Phone Alert Status Client Setup......................................................................5
3.4 SAM 4S Xplained Pro Phone Alert Status Client Setup ........................................................................5
4Phone Alert Status Notifications ................................................................................6
5Software Setup.............................................................................................................7
5.1 Installation Steps...................................................................................................................................7
5.2 Build Procedure.....................................................................................................................................7
6Console Logging .......................................................................................................10
7Running the Demo.....................................................................................................11
8BluSDK Software Architecture..................................................................................15
9ATMEL EVALUATION BOARD/KIT IMPORTANT NOTICE AND DISCLAIMER........16
10 Revision History ........................................................................................................17

ATBTLC1000 BluSDK Phone Alert Status–Getting Started Guide [USER GUIDE]
Atmel-42547C-ATBTLC1000-BluSDK-Phone-Alert-Status-Profile-Getting-Started-Guide_UserGuide_022016
3
3
1 Demo Setup
Figure 1-1. Demo Setup for Phone Alert Status
2 Supported Hardware Platforms and IDEs
Table 2-1. BluSDK –Supported Hardware and IDEs
Platform
MCU
Supported
BLE device
Supported evaluation kits
Supported IDEs
SAM L21 (MCU)
ATSAML21J18B
ATBTLC1000
ATBTLC1000-XSTK
(ATSAML21-XPRO-B + ATBTLC1000
XPRO)
Atmel Studio v7.0
SAM L21 (MCU)
ATSAML21J18A
ATBTLC1000
ATSAML21 XPRO + ATBTLC1000
XPRO
Atmel Studio v7.0
SAM D21 (MCU)
ATSAMD21J18A
ATBTLC1000
ATSAMD21-XPRO + ATBTLC1000
XPRO
Atmel Studio v7.0
SAM G55 (MCU)
ATSAMG55J19
ATBTLC1000
ATSAMG55-XPRO + ATBTLC1000
XPRO
Atmel Studio v7.0
SAM 4S (MCU)
ATSAM4SD32C
ATBTLC1000
ATSAM4S-XPRO + ATBTLC1000
XPRO
Atmel Studio v7.0
Android phone
Atmel Smart Connect app
(Phone Alert Status
Server)
ATBTLC1000+
Supported Atmel MCU
(Phone Alert Status
Client)
BLE Link

ATBTLC1000 BluSDK Phone Alert Status–Getting Started Guide [USER GUIDE]
Atmel-42547C-ATBTLC1000-BluSDK-Phone-Alert-Status-Profile-Getting-Started-Guide_UserGuide_022016
4
4
3 Hardware Setup
3.1 SAM L21 Xplained Pro Phone Alert Status Client Setup
Figure 3-1. ATBTLC1000 Xplained Pro Extension Connected to a SAM L21 Xplained Pro
3.2 SAM D21 Xplained Pro Phone Alert Status Client Setup
Figure 3-2. ATBTLC1000 Xplained Pro Extension Connected to a SAM D21 Xplained Pro

ATBTLC1000 BluSDK Phone Alert Status–Getting Started Guide [USER GUIDE]
Atmel-42547C-ATBTLC1000-BluSDK-Phone-Alert-Status-Profile-Getting-Started-Guide_UserGuide_022016
5
5
3.3 SAM G55 Xplained Pro Phone Alert Status Client Setup
Figure 3-3. ATBTLC1000 Xplained Pro Extension Connected to a SAM G55 Xplained Pro
3.4 SAM 4S Xplained Pro Phone Alert Status Client Setup
Figure 3-4. ATBTLC1000 Xplained Pro Extension Connected to a SAM 4S Xplained Pro

ATBTLC1000 BluSDK Phone Alert Status–Getting Started Guide [USER GUIDE]
Atmel-42547C-ATBTLC1000-BluSDK-Phone-Alert-Status-Profile-Getting-Started-Guide_UserGuide_022016
6
6
4 Phone Alert Status Notifications
The Profile defines two roles; the Phone Alert Server and the Phone Alert Client. The Phone Alert Server
is the device that originates the alerts and the Phone Alert Client is the device that receives the alerts and
alerts the user.
The Phone Alert Client which is a GATT client, is the configuration that’s implemented on the
ATBTLC1000 + along with supported platform.
The example application utilizes the SW0 button on the supported platform to demonstrate the notification
use-cases. A BLE compatible Android device running the Atmel Smart Connect mobile application
provides the Phone Alert Server (PAS Server) functionality in this example. On the application, once the
service is discovered and the user clicks on PAS service, notifications are enabled.
1. Post connection with mobile device, the first button press will set the PAS server to ‘Silent’ mode.
2. The second button press, the device will be set to ‘Mute’ State.
3. The third button press, will return the device back to ‘Normal’ Mode.
4. The fourth button press issues a ‘Read Characteristic’ request that will read the characteristics of
‘Alert Status’, ‘Ringer Settings’, and ‘Ringer Control Point’.
Note: iOS devices like iPhone®do not natively support Phone Alert Status profile. This demo/example
will work only with BLE compatible Android devices running the Atmel Smart Connect mobile
application.

ATBTLC1000 BluSDK Phone Alert Status–Getting Started Guide [USER GUIDE]
Atmel-42547C-ATBTLC1000-BluSDK-Phone-Alert-Status-Profile-Getting-Started-Guide_UserGuide_022016
7
7
5 Software Setup
5.1 Installation Steps
1. Atmel Studio installation [Atmel Studio 7.0 (build 594) Installer –with .NET]
http://www.atmel.com/tools/atmelstudio.aspx.
(Note: SAM L21 Rev B/SAM D21/SAM G55/SAM 4S part pack is built-in as part of Atmel Studio
7.0)
2. Atmel USB Driver Installer http://www.atmel.com/tools/atmelstudio.aspx.
3. Install the standalone ASF package from
http://www.atmel.com/tools/AVRSOFTWAREFRAMEWORK.aspx.
Note: Refer to the BluSDK release notes for updates to version numbers of the components mentioned
above.
This package will install the following examples within the Atmel Studio environment.
1. Blood Pressure Application for SAM L21.
2. Blood Pressure Application for SAM D21.
3. Blood Pressure Application for SAM G55.
4. Blood Pressure Application for SAM 4S.
5.2 Build Procedure
The following procedure is explained for the SAM L21 application example. The same procedure is valid
for the case of all the other supported platforms as well.
Figure 5-1. Creating a New Project
1. Select “SAML,32-bit” in device family, enter “Phone Alert Status” in search window, and expand
Atmel Corp. Projects. The location and the name of the project can be selected in the respective
fields. Click OK.

ATBTLC1000 BluSDK Phone Alert Status–Getting Started Guide [USER GUIDE]
Atmel-42547C-ATBTLC1000-BluSDK-Phone-Alert-Status-Profile-Getting-Started-Guide_UserGuide_022016
8
8
Figure 5-2. Selecting the Phone Alert Status Application from Example Projects
2. Accept the license Agreement. The studio will generate the Phone Alert Status Server project for
SAM L21.

ATBTLC1000 BluSDK Phone Alert Status–Getting Started Guide [USER GUIDE]
Atmel-42547C-ATBTLC1000-BluSDK-Phone-Alert-Status-Profile-Getting-Started-Guide_UserGuide_022016
9
9
3. Build the solution.
Figure 5-3. Building the Phone Alert Status Application
4. Download the application via the USB to the SAM L21 board using the Device Programming option
available in Tools, as mentioned below.
Figure 5-4. Programing the SAML21
b
5. Inside device programming the user has to select the correct configuration for the device and finally
program the device by using program button.

ATBTLC1000 BluSDK Phone Alert Status–Getting Started Guide [USER GUIDE]
Atmel-42547C-ATBTLC1000-BluSDK-Phone-Alert-Status-Profile-Getting-Started-Guide_UserGuide_022016
1
0
10
Figure 5-5. Flashing the Phone Alert Status Application
6. Once the application is flashed the Phone Alert Status Client Application is ready for usage.
6 Console Logging
For the purpose of debugging, a logging interface had been implemented in the Phone Alert Status
Application.
The logging interface utilizes the same EDBG port that connects to supported platform. A serial port
monitor application (for example TeraTerm) shall be opened and attached to the corresponding COM port
enumerated on the PC by the device with a baud rate of 115200.