Atop Smart Security IS150 User manual

IS150
Smart Security
Web User’s Manual
v.1.0
May, 2013

2
Important Announcement
The information contained in this document is the property of Atop Technologies, Inc., and is supplied
for the sole purpose of operation and maintenance of Atop Technologies, Inc. products. No part of this
publication is to be used for any other purposes, and it is not to be reproduced, copied, disclosed,
transmitted, stored in a retrieval system, or translated into any human or computer language, in any
form, by any means, in whole or in part, without the prior explicit written consent of Atop Technologies,
Inc., offenders will be liable for damages. All rights, including rights created by patent grant or
registration of a utility model or design, are reserved.
Disclaimer
We have checked the contents of this manual for agreement with the hardware and software
described. Since deviations cannot be precluded entirely, we cannot guarantee full agreement.
However, the data in this manual is reviewed regularly and any necessary corrections included in
subsequent editions. Suggestions for improvement are welcome. All other product names referenced
herein are registered trademarks of their respective companies.
Published by
Atop Technologies, Inc.
2F, No. 146, Sec. 1, Tung-Hsing Rd.
Jubei, Hsinchu 30261
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
www.atop.com.tw
www.atop-tech.com
Copyright © 2013 Atop Technologies, Inc. All rights reserved. Technical data is subject to change. All
other product names referenced herein are registered trademarks of their own respective companies.

Atop Smart Security Server
IS150
User Manual V1.0
3
Contents
1Preface..................................................................................................... 5
2Introduction............................................................................................. 8
2.1 Product Overview .....................................................................................................8
2.2 Features...................................................................................................................10
3Getting Started.......................................................................................11
3.1 Model Comparison .................................................................................................11
3.2 First Time Installation.............................................................................................11
3.3 Finding the device ..................................................................................................11
3.4 Factory Default Settings ........................................................................................13
4Web Configuration.................................................................................15
4.1 Web Configuration Overview.................................................................................15
4.2 Operation Modes ....................................................................................................17
4.2.1 Regular AP Gateway Mode............................................................................17
4.2.2 AP Client Mode...............................................................................................19
4.3 System Information ................................................................................................22
4.3.1 Device Information..........................................................................................22
4.3.2 LAN Information..............................................................................................22
4.3.3 DI/DO Information...........................................................................................23
4.3.4 Wireless Information.......................................................................................23
4.3.5 GPRS/UMTS Information...............................................................................24
4.3.6 Wireless Client Table (Regular AP Gateway Mode) ......................................24
4.3.1 DHCP Client Table (Regular AP Gateway Mode)..........................................25
4.4 Network Settings ....................................................................................................26
4.4.1 LAN (Regular AP Gateway Mode) .................................................................26
4.4.2 Local Area Network (AP Client Mode)............................................................27
4.4.3 WAN (Regular AP Gateway Mode)................................................................29
4.4.4 Virtual Server (Regular AP Gateway Mode) ..................................................30
4.4.5 SNMP Settings...............................................................................................31
4.4.6 DHCP Server (Regular AP Gateway Mode) ..................................................32
4.5 Wireless Settings....................................................................................................33
4.5.1 Secure Wireless Wi-Fi Network......................................................................33

Atop Smart Security Server
IS150
User Manual V1.0
4
4.5.2 Basic Settings (Regular AP Gateway)............................................................34
4.5.3 Mobile Station (AP Client) ..............................................................................40
4.5.4 Security Settings (Regular AP Gateway Mode) .............................................43
4.5.5 Advanced Settings..........................................................................................46
4.6 Input / Output ..........................................................................................................48
4.7 System Setting........................................................................................................49
4.7.1 Firmware Upgrade..........................................................................................49
4.7.2 Time................................................................................................................50
4.7.3 Password........................................................................................................51
4.7.4 Restore to Default...........................................................................................52
4.7.5 Reboot............................................................................................................53
4.8 Logout......................................................................................................................53
5WAN Configuration................................................................................54
5.1 PPPoE......................................................................................................................54
5.2 DHCP........................................................................................................................56
5.3 Static IP....................................................................................................................57
5.4 GPRS/UMTS ............................................................................................................58
5.4.1 Enabling the SIM card....................................................................................58
5.4.2 List of Compatible Internet Service Providers (ISP).......................................61
5.5 LED Indicators ........................................................................................................62
6Warranty .................................................................................................63

Atop Smart Security Server
IS150
User Manual V1.0
5
1 Preface
Purpose of the Manual
This manual supports you during the installation and configuring of the IS150 Smart Security Server
only, as well as it explains some technical options available with the mentioned product. As such, it
contains some advanced network management knowledge, instructions, examples, guidelines and
general theories designed to help users manage this device and its corresponding software; a
background in general theory is a must when reading it. Please refer to the Glossary for technical
terms and abbreviations (if any).
Who Should Use This User Manual
This manual is to be used by qualified network personnel or support technicians who are familiar with
network operations; it might be useful for system programmers or network planners as well. This
manual also provides helpful and handy information for first time users. For any related problems
please contact your local distributor, should they be unable to assist you, please redirect your
inquiries via www.atop.com.tw or www.atop-tech.com.
Supported Platform
This manual is designed for the IS150 Smart Security Server and that model only.
Warranty Period
We provide a 3 year limited warranty for IS150 Smart Security Server.

Atop Smart Security Server
IS150
User Manual V1.0
6
Manufacturers Federal Communication Commission Declaration of Conformity Statement
Model: IS150
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of
other channels is not possible.
This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.
※
FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz
to reduce the potential for harmful interference to co-channel Mobile Satellite systems.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 cm between the
radiator & your body.

Atop Smart Security Server
IS150
User Manual V1.0
7
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Model: IS150
Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC
This equipment is in compliance with the essential requirements and other relevant provisions of
1999/5/EC.
The following standards were applied:
EMCEN 301.489-1 v1.4.1; EN 301.489-17 v1.2.1
Health & Safety EN60950-1: 2001; EN 50385: 2002
Radio EN 300 328 v 1.7.1; EN 301.893 v 1.5.1
The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive 1999/5/EC
has been followed.
This device also conforms to the EMC requirements of the Medical Devices Directive 93/42/EEC.
Note: This equipment is intended to be used in all EU and EFTAcountries. Outdoor use may be
restricted to certain frequencies and/or may require a license for operation. For more details, contact
Atop Technical Support.
European Union
This system has been evaluated for RF exposure for humans in reference to the ICNIRP
(International Commission on Non-Ionizing Radiation Protection) limits. The evaluation was based on
the EN 50385 Product Standard to Demonstrate Compliance of Radio Base stations and Fixed
Terminals for Wireless Telecommunications Systems with basic restrictions or reference levels related
to Human Exposure to Radio Frequency Electromagnetic Fields from 300 MHz to 40 GHz. The
minimum separation distance from the antenna to a general bystander is 20 cm (7.9 inches).

Atop Smart Security Server
IS150
User Manual V1.0
8
2 Introduction
2.1 Product Overview
The IS150 Smart Security Server series is our new line of security products designed to allow
remote access through its rich wired and wireless interfaces creating a complete solution for your
home and/or store security and surveillance needs.
As an example, you can connect multiple sensors and detectors to IS150 using its digital input
interface and connect alarms to IS150 using its digital output interfaces; this example illustrates a
typical security system guarded by IS150, Figure 2.1.

Atop Smart Security Server
IS150
User Manual V1.0
9
Figure 2.1

Atop Smart Security Server
IS150
User Manual V1.0
10
2.2 Features
IS150 is our latest addition to our smart security products; its powerful architecture makes it a perfect
choice for business/home needs in which security is a decisive factor. It rewards our customers with
superb connectivity. Among its many characteristics, we could mention:
Send alarm messages through email or SMS
Provide 8-Door access control
Monitor sites using IP Camera from anywhere in the world
16 sets of independent digital inputs and 8 digital outputs for variety of uses
Provide iOS / Android / Windows / Web interfaces for monitor and configuration
Watchdog protected to recover from system crash

Atop Smart Security Server
IS150
User Manual V1.0
11
3 Getting Started
3.1 Model Comparison
Table 3.1
Model
Description
IS150-WG
Smart Security Server with WCDMA and WiFi module
IS150-G
Smart Security Server with WCDMA module only
IS150-W
Smart Security Server with WiFi module only
IS150
Smart Security Server without any wireless function
3.2 First Time Installation
Please consult your Hardware Installation Guide when attempting the installation. Also, please follow
all safe procedures when doing so.
3.3 Finding the device
As soon as the device is connected to the network, the user can search for its IP settings using
Device View © , (utility that comes in the CD); as noted in Figure 3.1 below, important information
such as the IP, MAC address, etc is going to be displayed.

Atop Smart Security Server
IS150
User Manual V1.0
12
Figure 3.1
If the device’s name is double-clicked or the Internet Explorer logo is clicked, Device View would
open the Web UI of IS150 using the system default browser. A window will pop-out that will prompt
you to enter username and password (see Factory Default Settings for more information), proceed
then to click “OK”, Figure 3.2. If credentials are entered correctly, the Web UI can then be accessed.
Figure 3.2

Atop Smart Security Server
IS150
User Manual V1.0
13
3.4 Factory Default Settings
Upon arrival, the device will be set as Regular AP, the rest of the settings are as follow:
Table 3.2
Operation Mode
Regular AP Gateway
AP Client
Network
LAN Interface
IPAddress
10.0.50.100
N.A.
Subnet Mask
255.255.0.0
WAN Setting
PPPoE
Enabled
N.A.
Dial when boot up
Enabled
Username
Blank
Password
Blank
Virtual Server
Disabled
SNMP Setting
System Contact
Contact
System Location
Location
System Name
Device’s MAC address
Read Community
Disabled
Write Community
Disabled
DHCP Server
DHCP
Disabled
N.A.
Wireless
Basic Setting
Radio Off
Disabled
N.A.
SSID
IS150
SSID Broadcast
Enabled
Wireless Mode
802.11 b/g/n
Channel
Auto
BandWidth
40MHz
Secondary Channel
Disabled
Transmit Rate
Disabled

Atop Smart Security Server
IS150
User Manual V1.0
14
Security Setting
Security Mode
Disabled
N.A.
Mobile Station
Radio On/Off
N.A.
Enabled
Topology
Infrastructure
Band mode
Disabled
TxRate
Best (auto)
Channel
Disabled
BandWidth
Secondary Channel
Authentication Mode
OPEN
Encryption Type
N.A.
NONE
Advanced Setting
Regulatory Domain
US(FCC5-FCCA)
Tx Power
100%
Short GI
Enable
WMM
Enable
STP
Disabled
Input/ Output
DI/O Setting
DO 1
Off
DO 2
Off
System Setup
Time
Current Date/Time
Time from NTP Server
NTP
Enabled
NTP Server
pool.ntp.org
Time Zone
(GMT+08:00) Taipei
Password
User name
admin
Old password
Blank
New password
Repeat new password

Atop Smart Security Server
IS150
User Manual V1.0
15
4 Web Configuration
4.1 Web Configuration Overview
IS150 Series’ Web Configuration is designed into two different modes for ease of use to suit customer
needs. The Web Configuration appears as follows, Figure 4.1.
Figure 4.1
On the left side, a menu-tree appears with all the modes and options available, while on the right side
of your screen the contents of each mode/option will be displayed in a graphical state. Since each
Mode of operation is different, the content will differ, for more information on each selection please
refer to each option’s Section throughout the manual.
In general, there will be three buttons which will be present at the end of almost each configuration:

Atop Smart Security Server
IS150
User Manual V1.0
16
Table 4.1
Button
Function
Saves the current configuration input on the page only, the configuration
itself will not be applied to the device. We recommend users to use this
button before the configuration process is completed and then press
“Apply” at the last step.
Save and apply the current configuration input on the page. On some
pages, the device may need to reboot, we strongly advise to save the
device’s settings before reboot.
Cancel the current configuration input and shows the original settings.

Atop Smart Security Server
IS150
User Manual V1.0
17
4.2 Operation Modes
4.2.1 Regular AP Gateway Mode
Figure 4.2
Regular AP Gateway mode is the factory default and the first option on the screen. It allows network
devices to connect to the network over Wi-Fi or LAN, relaying data between the wired and wireless
devices in the network. It allows multiple wireless clients to access the network through IS150’s
WLAN interface (UMTS/PPPoE connection). Its corresponding complete menu-tree is as follows in
Figure 4.3.

Atop Smart Security Server
IS150
User Manual V1.0
18
Figure 4.3
Steps for a quick setting for the IS150 as a Regular AP Gateway are:
On operation mode choose “Regular AP Gateway” (if the device is not in factory default).
Remember to click on “Save” before you continue to the next step.
Go to Network →LAN Settings, enter the IP Address, Subnet Mask of the device
Go to Network →WAN Settings, select a method that connects the device to the Internet.
Go to Network →Wireless Setting →Basic Settings; here you can change the Network
Name (SSID) to your preferred name, you might want to first click on “Scan network” to find

Atop Smart Security Server
IS150
User Manual V1.0
19
whether there are neighbors with a name matching yours (this is done for preventing any conflict
over networks).
At this point you may decide to change other settings such as the Wireless Mode, whether to
have Automatic Channel Selection, the Bandwidth, Transmission Rate and the Secondary
Channel (only available when on 802.11a/n and 802.11b/g/n modes).
Next go to Security Settings, and on Security Mode choose which security protocol will be
used in the network. We strongly recommend not leaving this section as disabled.
Click “Apply”, and wait for the changes to take effect. This will apply all the previous changes
all together.
4.2.2 AP Client Mode
This mode allows your IS150 to connect to an Access Point (AP). Ethernet clients connected to
IS150 over the Local Area Network (LAN) are allowed to access the network through IS150’s wireless
interface.
Figure 4.4
Its corresponding complete menu-tree is as follows in Figure 4.5.

Atop Smart Security Server
IS150
User Manual V1.0
20
Figure 4.5
Remember that your IS150 can function as both a Regular AP Gateway and as an AP Client (the
latter connected to the first one).
Supposing we already have the network physically installed, the steps for configuring your IS150 as
an AP Client are as follows.
On Operation Mode choose AP Client. Click on “Save Settings”
Go to Network →Wireless Setting →Mobile Station and click on “Scan network” to choose
an SSID.
A window/tab will pop out; in that new window/tab, there will be the names of the surrounding
Wireless Networks. Choose the one that you already designated as your Regular AP by
selecting its corresponding SSID.