Audiovox Movies 2 Go MMSV58 User manual

MMSV58
5.8" LCD SUN VISOR MONITOR
WITH MIRROR AND DOME LIGHT
0
Installation Guide

Notice
An LCD display and/or video monitor may be installed in a motor vehicle and visible to the driver
if the LCD display or video monitor is used for vehicle information, system control, rear or side
observation or navigation. If the LCD display or video monitor is used for television reception,
video or DVD play, the LCD display or video monitor must be installed so that these features will
only function when the vehicle is in ‘park’ or when the vehicle’s parking brake is applied.
An LCD display or video monitor used for television reception, video or DVD play that operates
when the vehicle is in gear or when the parking brake is not applied, must be installed to the rear
of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor
vehicle.
Warnings
♦ Keep the LCD display clean and dry.
♦Do not use any solvents or cleaning materials when cleaning the LCD display.
♦Do not use any abrasive cleaners, they may scratch the LCD display. Use only a lightly
dampened lint free cloth to wipe the LCD display if it is dirty.
♦Remember to leave the dome light switch in the off positions when the vehicle is unattended,
as the dome lights, if left on, can drain the vehicle’s battery.
♦Do not apply pressure to the LCD display.
♦ Caution children to avoid touching or scratching the LCD display, as it may become dirty or
damaged.
♦ This product is designed to operate with a 12 volt, negative ground battery system.
♦ Do not operate the monitor at temperatures below 32°F (0°C) or above 104°F (40°C).
♦ Do not expose to direct sunlight for extended periods of time.
♦ Never attempt your own repairs. This unit should be installed and repaired by qualified
technicians or service personnel.
♦ Use proper insulation material to prevent short-circuiting of the supply system.
1

MATERIALS INCLUDED IN THIS PACKAGE:
1) MMSV58SunVisorVideoMonitor(P/N136-3781)(1pc)
2) MonitorMountingShroud(P/N1024053)(1pc)
3) RemoteControl(P/N136-B3696)(1pc)
4) HardwarePackage:-
• M2.5x#8”Screws(4pcs)
• RubberScrewPlugCaps ((138-1324)(4pcs)
5) 7PinPowerWireHarness(P/N1123455)(1pc)
OOLS REQUIRED:
hears
l(forremovalofpanelsasnecessary)
12voltDCandcontinuity:Donotuseatestlightorlogicprobe)
nnect to vehicle power source). Requirements will vary from vehicle to
T
Rotary ToolPhillipsScrewdriver
UtilityorRazorKnifeorS
WireStrippers
Upholsteryhooktoo
ElectricalTape





GROUND ACTIVATED
MaskingTape
Multimeter(toverify
FinePointMarker–tomarkvisor
Misc. electrical connectors (to co
vehicle.
2

INSTALLATION NOTES
• NOTE: System component installation options vary, see the individual owner’s
manuals for each component in your system to obtain a full understanding of each
component’s operation.
• NOTE: Each vehicle is different. Your specific disassembly and reassembly may
vary slightly from the installation guide shown.
INSTALLING THE MMSV58
1. Remove the Sun Visor from the vehicle.
With Illuminated Vanity Mirror
• Remove visor attaching hardware (screw) and set aside for re-assembly.
• Pull visor downward and disconnect any power connections.
• Once the visor is removed, place it on clean flat work surface
Figure 1. Sun Visor With Vanity Mirror
Without Illuminated Vanity Mirror
• Remove visor attaching hardware (screw) and save for re-assembly.
• Once the visor is removed, place it on clean flat work surface
Figure 2. Sun Visor Without Vanity Mirror
3

2. Remove all accessories from the visor such as mirror/door/light assemblies, etc (if
applicable) and set aside for re-assembly.
Figure 3. Sun Visor With All Accessories Removed
3. Once all accessories are removed, check the dimensions and material depth of the sun
visor to estimate the fit for your application.
NOTE: If the visor had no accessories to remove and does not have a open cavity,
measure the thickness of the visor material between the rigid material in the center and
the surface.
Figure 4. Sun Visor With All Accessories Removed
4. Using the rear of the visor-mounting shroud as a template, mark the visor.
Shroud used as
template
Figure 5. Marking The Visor Material
4

5. Using a Razor Knife cut an “X” through the material.
Figure 5. Cutting The Visor Material
6. Peel back the 4 flaps. Carefully cut out the plastic of the visor using a rotary tool. Be sure
that the tool does not grab the fabric/leather or damage may occur to the material. Lay
the 4 flaps back into the visor cavity.
7. Push the power/signal harness connector thru the back of the shroud and press the
shroud in the visor cavity. NOTE: The cavity may require some grinding using a rotary
tool to properly seat the shroud into the cavity. If grinding is needed be sure not to
damage the visor material.
Figure 6. Power/Signal Harness And Shroud Installed
8. Adhere the visor mounting shroud. (Example: silicone, two part quick drying epoxy, hot
glue, screws if a double wall is present, double side tape, etc) Place the shroud back into
the cavity and apply a good amount of pressure to the base if glue tape or epoxy is used
sets. Make sure you have pulled the monitor connector through the access hole on the
lower right hand side of the shroud. NOTE: When using glue or double side tape, make
sure to use only high temperature rated products that can handle the extreme
temperatures of the vehicles interior
9. Plug the power power/signal harness into the rear of the MMSV58.
5

Figure 7. Installing The Monitor Shroud
10. Snap the screen into the visor mounting shroud Screw the screen to the visor mounting
shroud using the 4 screws (supplied).
11. Install the 4 screw caps (supplied) in the holes on the 4 corners of the assembly.
Figure 8. Installing The Monitor
12. Reinstall the sun visor in its original position using the attaching hardware removed in
step 1. of this installation procedure.
13. Route the power/signal harness from the sun visor down the A-Pillar and behind the
dashboard for connections to the video equipment and/or backup camera.
6

WIRING
GROUND ACTIVATED
Figure 9. Power/Signal Harness
MMSV58
VCP (VIDEO 1)
DVD (VIDEO 2)
Video Source
Power Source
Emergency
Brake Switch
Vehicle Ground
Figure 10. Typical System Installation
7

TROUBLESHOOTING
Remedy:
-Verify +12 VDC on Red wire at 7 pin Harness behind video
monitor. Verify ground connection with continuity test from
known good ground to black wire at 7 pin Harness
-Verify that the correct source is selected (i.e.: 1,2,3 or 4).
Verify that the source is on and playing a known good media
(such as a videotape). Verify connections at both ends of the
source component harness. Verify that the Gray wire is
connected to the Emergency Brake wire.
-Check batteries in the hand held remote.
Symptom:
No power at Video Monitor
Power but no video or sound
No Infrared Remote Functions
8

9
© Copyright 2004 AEC 150 Marcus Blvd. Hauppauge, NY 11788 128-7158