Audiovox Mm530 User manual

MM530

5.3" LCD HEADREST MONITOR

EXPLANATION OF GRAPHIC SYMBOLS

WARNING:

TOPREVENTFIREORELECTRICSHOCKHAZARD,DONOTOPEN

CAUTION:

1. This product is designed to operate with a 12 volt, negative ground

battery system.

2. Refer to the electrical connection diagram to avoid wrong connection

of the electrical system.

Always use authorized service center for service assistance.

3. Do not operate the monitor at temperatures below 32°F (0°C) or

above 104°F (40°C).

4. Keep the monitor clean and dry.

5. Never attempt your own repairs. This unit should be installed and

repaired by qualified technicians or service personnel..

6. Do not drop the monitor or expose to strong impacts.

7. Do not expose to direct sunlight for extended periods of time.

8. Use proper insulation material to prevent short-circuiting of the supply

system.

The lightning flash with arrowhead symbol, within an equilat-

eral triangle, is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s enclo-

sure that may be of sufficient magnitude to constitute a risk of

electric shock.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO

NOT REMOVE COVER (OR BACK) NO SERVICEABLE PARTS

INSIDE REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The exclamation point within a triangle is intended to alert the

user that important operating and servicing instructions

A. Precaution:

1. Before installation, verify that it will not damage electrical wires, fuel

lines, brake lines, hoses, exhaust system components or any other

items that will impair the operation of the vehicle.

2. Ensure the cable has already been pulled through the supporting

pipe before installing the base into the headrest. Ensure there is no

foreign material trapped inside the enclosure before installing the

monitor into the base.

3. Tighten all screws/bolts/nuts securely for installation.

4. To avoid electrical hazards, do not disassemble the monitor.

5. Use only the supplied cables. Disconnect all cables from the

signal source before disconnecting it from the monitor.

6. When cleaning, make sure the system is unplugged from the power

source. Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth to clean the unit.

IMPORTANT

An LCD panel and/or video monitor may be installed in a motor

vehicle and visible to the driver if the LCD panel or video monitor is

used for vehicle information, system control, rear or side observation

or navigation. If the LCD panel or video monitor is used for television

reception, video or DVD play, the LCD panel or video monitor must be

installed so that these features will only function then the vehicle is in

‘park’ or when the vehicle’s parking brake is applied.

An LCD panel or video monitor used for television reception, video or

DVD play that operates when the vehicle is in gear or when the parking

brake is not applied, must be installed to the rear of the driver’s seat

where it will not be visible, directly or indirectly, to the operator of the

motor vehicle.

B. Contents:

1.1xMainUnitMM530

2. 1 x AV Adapter Cable

3. 1 x Din-to-RCA Cable

4. 1 x Din Cable Clip

5.1xOwner’sManual

6. 1 x Fan Bracket

C. Installation:

Front View Top View

1.Installation will vary from vehicle to vehicle, as headrests in vehicles

are not standard.

2.This unit is intended for installation by professional installers.

3.The kit consists of the screen assembly, a clam shell housing and 1

key to remove the screen from the housing.

1) Remove the headrest f

from the vehicle for easi-

est installation.

2) Lay headrest on a flat sur-

face.

3) Using a Permanent Marker,

mark headrest material

along the exterior of the

Mountingtray.

4) Remove the Trim Ring and

mark an “X” from corner to

corner as shown.

Headrest Mounting:

Monitor Mounting

Tray

8)Using yourfingers, tearthefoam

out of the headrest leaving a

recess where the shell will be

inserted.

NOTE: Atthispointyouwillneedto

install the harness up through the

areaintotherecess.Itmaybehelp-

ful to follow one of the posts and tie

wrap it to the post for restraint.

5) Using the utility knife, cut the

headrest material along the “X”

lines. Do not cut the material

along the other lines at this

time.

6)Thiswillleaveyouwithan“X”cut

as shown.

7)Pulltheflapsupandcutthefoam

beneath the material to the

proper depth. Cut all four sides

of the foam.

10) Guide the cable through the side

openingoftheMountingTrayand

plugitintotheMonitor. Makesure

the connector locks into place.

Insertthe MonitorintotheMount-

ing Tray and secure the cable

using tie wraps or screws

11) Turn the Monitor around and in-

sertitintotheMountingTrayhous-

ing. Snap into place.

9) Lay the flaps of the headrest mate-

rial down into the recess and in-

sert the Mounting Tray into the re-

cess. Check for fit. If it does not fit

properly, you may need to remove

some more foam.

NOTE:TheMountingTraywillneedto

be secured to the headrest, either

by using tie straps, screws, etc...

12) Connect the Monitor‘s DIN Cable

to the external video source out-

put signal (from VCP/DVD, TV

Etc.)Test the system to verify

proper installation.

Fan Bracket Mounting*

The monitor can be mounted on a variety of surfaces using the

supplied fan bracket.

Select a location for the monitor and find a suitable surface to mount

the fan bracket. The mounting location* should be as firm, flat and

smooth as possible to ensure maximum adhesion. If the area is not

flat the bracket can be bent to conform to the shape of the surface.

Clean the area thoroughly and make sure that is dry before attempting

to mount the bracket. Remove the backing from the adhesive pad on

the bottom of the bracket and carefully place it in the desired mounting

location and press down firmly. Carefully align the mounting hole on

the bottom of the monitor with the screw on the top of the bracket.

Release the locking lever and turn the locking knob until it is tight.

Adjust the monitor angle and tighten the locking lever.

*Note: Please read the important notice on page three about monitor

location.

Screw

Spanner

LockingLever

LockingKnob

Screw

D. Controls/Indicators/Connectors:

Front View

1.AVInput Jack

2. Power Button

3. Source Button

4. Wide Button

5. Fan Bracket Mounting Hole

6. Picture Select Button

7. Volume Down Button

8. Volume Up Button

9. Headphone Jack

5678 9

RearView

9.DIN Jack

10.Video(Yellow)

11.AudioLeft (White)

12.Audio Right (Red)

13.Red+12 VDC

14.Black Ground

This manual suits for next models

Table of contents

Audiovox MM530 User manual

Popular Car Video System manuals by other brands