Austlift MAXIBINDER 202705 User manual

Wholesale of Lifting, Rigging, Load Restraint
& Height Safety products
202705 (8mm), 202707 (10mm)
MAXIBINDER
USER MANUAL
AUSTRALIAN LIFTING CENTRE PTY LTD
Australian Patent NO.
2006301899
1300 100 120
www.austlift.com.au

ALC UIM PC2027XX_0521
Maxibinder is a modern cargo tie down equipment. It has been chosen by
many transport companies as there preferred cargo tie down equipment.
The binder is designed with safety orientated concept, the market reports
shows work place accident has been reduced in ponderable rates after the
leaver load binder be replaced by Maxibinder.
Ergonomically operating is another outstanding feature, large lubber
handle is easer for you to grip, enclosed locking mechanism is designed to
preventing lose tensioning during transportation. It is light in weight, easy to
handle which made the binder to be a very popular product in transportation
industry.
As to market requirement, 10mm Maxibinder was lunched at August 2019.
MAXIBINDER
FEATURES
Load Restaint Innovator
Australian Lifting Centre
Safer
Quicker
Easier
• Ergonomically designed.
• Safer, quicker and easier to use.
• 1/8 chain link length adjustment.
• Alloy steel, heat treated for durability.
• Multiple purposes.
• Designed for a higher pre-tensioning strength.
• Designed and manufactured to AS/NZS 4344.
MAXIBINDER USER MANUAL
21300 100 120 www.austlift.com.au

ALC UIM PC2027XX_0521
INSPECT MAXIBINDER BEFORE USE
WARNING
• Make sure there is no dirt or soil in the mechanism to avoid jamming.
• Move the handle down to free wheel position, pull the chain in both
direction to confirm the chain wheel is rotating freely.
• Lift control plate, move the handle towards to front, make sure ratchet
mechanism, springs and stop plate are working properly.
• Be aware the handle has a built in safety lock mechanism, this is to lock the
handle is firmly finished (stowing) position, to prevent the pawl releasing
due to shacking or vibration.
DO NOT USE MAXIBINDER FOR
LIFTING PURPOSE
CODE LASHING
CAPACITY
DESTRUCTIVE
TEST
CHAIN
TRAVELLING
202705 (8mm) 3800kg 7,600kg 305mm
202707 (10mm) 6000kg 12,000kg 305mm
CODE CHAIN HOOK Wt.
(kg)
202705
(8mm) 8mm G70 0.55M G70 8mm Grab Hook 5.4
202707
(10mm) 9mm G100 0.6M G70 10mm Grab Hook 6.4
MAXIBINDER USER MANUAL
3
MAXIBINDER USER MANUAL

ALC UIM PC2027XX_0521
Position the Maxibinder with handle
in the upright finished (stowing)
position.
Connect the top hook of the
Maxibinder to binding chain, ensure
the binding chain is not twisted.
Once the top hook is connected, pull
out the control plate.
Push the handle all the way down to
the end, the handle will be locked
into the free wheel position.
HOW TO TENSION
To maximize the lashing capacity,
you should pull the bottom hook all
the way out, check there is no twist
on chain before you connect it to
the binding chain.
ATTENTION
STEP 1
STEP 2
STEP 3
STEP 4
Upright
Position
Top
Hook
Control Plate
MAXIBINDER USER MANUAL
41300 100 120 www.austlift.com.au

ALC UIM PC2027XX_0521
Pull the chain all the way out from
the binder and to connect the
bottom hook to your binding chain
at the furthest point.
Pull the control plate again and
move handle back to the middle
section, release the control plate
then start tensioning by moving the
handle up and down. The bottom
hook will begin to tension.
You only need 50kg on handle to achieve approximately 750kg force between
the hooks. This is higher than Australian Standard requirement which has
been requested by BlueScope and other Australian Companies.
NOTE: For your safety, you must stand on firm, flat, non-slip ground
when using the Maxibinder.
STEP 5 STEP 6
STEP 7
Bottom
Hook
MAXIBINDER USER MANUAL
5
MAXIBINDER USER MANUAL

ALC UIM PC2027XX_0521
The standard chain movement of the Maxibinder is 300mm, If you see the
bottom hook is closing to the body and your load still lose, you should check
and redo it by the following:
• Assort the slack on your binding chain then do it again.
• Check for any squashing on your load while binding, if noted retention load.
• The chain in Maxibinder can be replaced by a larger one. If you need it,
please contact our dealer or call 1300 100 120 for advise.
When ratcheting is finished, ensure
the handle is stowed in upright
position and check the safety lock
is fully engaged.
HOW TO TENSION
STEP 8
STEP 9
Safety
lock
During transport, regular checks
are required to ensure the load is
secured.
ATTENTION
MAXIBINDER USER MANUAL
61300 100 120 www.austlift.com.au

ALC UIM PC2027XX_0521
Pull the control plate back and move
the handle downward.
By pushing the handle downwards
you will feel the tension increase and
the pawl will push out.
Further downward pressure will
cause the Maxibinder to create a
“BIG BANG“ the handle will now be in
freewheel position and the tension
released.
Take hooks off your binding chain
and stow the handle in upright
position, cleaning it, put it back to
your tool box.
HOW TO RELEASE
STEP 1
STEP 2
STEP 3
STEP 4
Control Plate
MAXIBINDER USER MANUAL
7
MAXIBINDER USER MANUAL

ALC UIM PC2027XX_0521
• Check Springs, there are two sets of springs, one on the handle and
one on the pawl. Please replace it if you see the spring is weakened or
malfunctioning.
• Check control plat, ratchet gear, central pin and all other moving parts for
signs of wear and make sure they are functioning properly.
• Ensure the unit is kept clean and free from dirt.
• Use high pressure air or water to flush out is permitted.
• Regularly apply lubricant all moving parts with spray lithium grease is required.
The MaxiBinder is a mechanical devise, and require regularly inspection and
maintenance .
MAINTENANCE
CHECK LIST
LITHIUM GREASE
MAXIBINDER USER MANUAL
81300 100 120 www.austlift.com.au

ALC UIM PC2027XX_0521
1
4
2
3
SPARE PARTS FOR
MAXIBINDR
202705
(8mm)
2027010
(10mm)
NO. Name CODE CODE
1Paw & Paw Spring 050011SP 050021SP
2Control Plate 050012SP 050022SP
3Main Handle Assembly
(Include Control Plate) 050013SP 050023SP
4Tail Swivel 050016SP 050026SP
SPARE PARTS
MAXIBINDER USER MANUAL
9
MAXIBINDER USER MANUAL

Copyright Australian Lifting Centre
Specifications and dimensions subject to change without notice.
1300 100 120
AUSTRALIAN LIFTING CENTRE
www.austlift.com.au
Wholesale of Lifting, Rigging, Load Restraint &
Height Safety products
Head Office (NSW)
43 Frank Street
Wetherill Park, NSW 2164
Ph : 02 9757 2277
WA Office
42 Mulgul Road
Malaga, WA 6090
Ph : 08 9248 6674
VIC Office
475 Dohertys Road
Truganina, VIC 3029
Ph : 03 9314 5525
QLD Office
7 Durbell Street
Acacia Ridge, QLD 4110
Ph : 07 3272 0777
ALC UIM PC2027XX_0521