auto maskin Marine Pro Series User manual

Publication P/N 1500932
Installation Manual
Marine Pro Series
RP 480i Remote Panel
Marine Watch S Series
S-ONE Alarm Panel

Table of contents
1 Preface 3
1.1 About this Manual 3
1.2 Responsibilities 3
1.3 Revisions 3
2 Ordering Information 4
3 Overview 5
3.1 Overview of the Marine Pro Series 5
3.2 Overview of the Marine Watch S Series 5
3.3 Networking 5
4 Installation 6
4.1 Mounting 6
4.1.1 Panel Cut-out 6
4.1.2 Mounting Screws 6
4.1.3 Screw Torque 7
4.1.4 Strain Relief 7
4.2 Connections & Wiring 8
4.2.1 General 9
4.2.2 Supply [T1-4] 9
4.2.3 Flexible I/O [T5-12] 9
4.2.4 CAN [T13-15] 10
4.2.5 Relay [T16-18] 10
4.2.6 Modbus RTU [T19-21] 10
4.2.7 HDMI 10
4.2.8 USB 10
4.2.9 Ethernet 10
4.2.10 NMEA 2000 10
5 Appendix A - Wiring 10
Page 2 (10)

1 Preface
1.1 About this Manual
This manual has been published primarily for professionals and qualified personnel.
The user of this material is assumed to have basic knowledge in marine systems, and must
be able to carry out related electrical work.
Work on the low-voltage circuit should only be carried out by qualified and
experienced personnel.
Installation or work on the shore power equipment must only be carried out by
electricians authorized to work with such installations.
1.2 Responsibilities
It is the sole responsibility of the installer to ensure that the installation work is
carried out in a satisfactory manner, that it is operationally in good order, that the
approved material and accessories are used and that the installation meets all
applicable rules and regulations.
Auto-Maskin continuously upgrades its products and reserves the right to make
changes and improvements without prior notice.
All information in this manual is based upon information at the time of printing. For updated
information, please contact your local distributor.
The crossed-out wheeled bin symbol indicates that the item should be
disposed of separately. The item should be handed in for recycling in
accordance with local environmental regulations for waste disposal.
By separating a marked item, you will help reduce the volume of waste
sent to incinerators or land-fill and minimize any potential negative impact
on human health and the environment.
1.3 Revisions
Manual revision: January 2023
Page 3 (10)

2 Ordering Information
The Marine Pro and Marine Watch series covers a wide range of compatible products within
both the series. Please visit our website for more information.
Page 4 (10)

3 Overview
3.1 Overview of the Marine Pro Series
3.2 Overview of the Marine Watch S Series
Typical installation shown below.
3.3 Networking
The products use Ethernet as a communication medium. Either connect the products
directly, or use Ethernet switches to expand the network.
For redundant Ethernet connection, managed Ethernet switches must be used.
Page 5 (10)

4 Installation
This chapter covers the installation of the RP 480i and Marine Watch S-ONE panels.
4.1 Mounting
Panels with a screen should be mounted so the operator can easily view and operate the
panel.
Ensure easy access to the rear wiring.
Use the included mounting frame.
The panel may be mounted on the engine’s supporting structure provided shock absorbers
are used either between the structure and the engine, or between the structure and the
panel enclosure.
Mount the panels with a screen with care to avoid
● mechanical damage
● exposure to water or other liquids
4.1.1 Panel Cut-out
The cut-out size is:
● 322 mm width, 191 mm height
4.1.2 Mounting Screws
When mounting the panel, the thickness of the wall where the cutout is determines the screw
length. Important to follow this guide not to damage the panel.
Wall thickness
Screw length
Included in package
0 - 2 mm
8 mm
Yes
3 - 5 mm
10 mm
No
6 - 8 mm
12 mm
No
9 -
Se formula below
No
When installing the panel on a thicker surface than 8 mm, use a screw length that is:
- Wall thickness + 6 mm.
- The gap between the screw head and the mounting frame must be 3 mm or less
when the screw is just inserted into the threads.
Screw thread size: M3.
Page 6 (10)

Using too long screws will damage the panel.
4.1.3 Screw Torque
The threads in the unit are pre-fitted with threadlocker. Use only two fingers on the
screwdriver as the image below shows to tighten the screws with a fair torque.
Do not over tighten the mounting screws.
4.1.4 Strain Relief
Secure cables that don’t have built in strain relief, such as HDMI, USB and Ethernet, with
double cable ties.
Page 7 (10)

4.2 Connections & Wiring
1
Power LED
51
HDMI
2
Supply
1. +24 V
2. 0 V
3. Power on2
4. Shield
6
USB-A (2.0 High-speed interface)
● USB 1
● USB 2
● USB 3
Reserved for software update, event log
extraction, and configuration file handling
3
Flexible I/O
5. I/O #1
6. I/O #2
7. I/O #3
7
Ethernet
● Ethernet 1, RJ45
● Ethernet 2, RJ45
2Not in use, connect to 24 V for future use
1Not in use
Page 8 (10)

8. I/O #4
9. I/O #5
10. I/O #6
11. I/O #7
12. I/O #8
Ethernet 1 is preferred for networking.
43
CAN bus, Relay, Modbus RTU
13. CAN L
14. CAN H
15. CAN 0V
16. Relay NC
17. Relay C
18. Relay NO
19. Modbus A
20. Modbus B
21. Modbus 0V
84
NMEA 2000 – isolated
4.2.1 General
Wires shall have a minimum area of 0.5 mm2, except the power supply where at least 1.0
mm2(17 AWG) wires shall be used.
4.2.2 Supply [T1-4]
The panels are designed to run on 24 V supply voltage.
Use a cable with twisted pair wires to minimize the effect of noise on the supply input.
Connect the Shield to the hull.
In marine installations, the 0 V should not be connected to the Shield. In a ship
installation, the hull is the Shield whilst the battery minus is the 0 V.
4.2.3 Flexible I/O [T5-12]
There are 8 flexible I/O channels available. They can be used for the following types .
5
● Switch input
● Switch output
● Voltage input
● 4-20 mA input
For analog measurements, use shielded cables to minimize disturbance. The
shield shall be connected to ground/hull, not to 0 V. Connect the shield to one end
of the cable only.
See the datasheet for detailed characteristics.
5See User Manual for respective products in order to see which functionality is available.
4Not in use
3Not in use
Page 9 (10)

4.2.4 CAN [T13-15]
Use shielded twisted cables for CAN, where CAN-H and CAN-L are twisted.
Connect the shield to one end of the cable only.
4.2.5 Relay [T16-18]
The relay has a 0.7 A overcurrent protection on the common pin.
See the respective User Manual for relay functionality.
4.2.6 Modbus RTU [T19-21]
Use shielded twisted cables for Modbus RTU, where A and B are twisted.
Connect the shield to one end of the cable only.
4.2.7 HDMI
Use strain relief as shown in the Strain Relief chapter.
See the respective User Manual for HDMI functionality.
4.2.8 USB
Typically, the USB interface is used for software update and file extraction.
When using the USB for other purposes, use strain relief as shown in the Strain Relief
chapter.
4.2.9 Ethernet
Use CAT-5 (or better) network cables.
Do not bend the Ethernet cable or pull the cable sideways more than necessary
during installation.
Use strain relief as shown in the Strain Relief chapter.
4.2.10 NMEA 2000
See the respective User Manual for NMEA 2000 functionality.
5 Appendix A - Wiring
Contact your distributor for example diagram of recommended wiring for RP 480i The
Marine Watch S-ONE is similar to this diagram.
Page 10 (10)