auto maskin Marine Watch S Series User manual

Publication P/N 1050161
User Manual
Marine Watch S Series
S-ONE Alarm Panel
S-ACE Annunciator Panel
I/O Cabinet

Table of content
1 About this manual 3
1.1 Intended audience 3
1.2 Responsibilities 3
1.3 Revisions 3
1.3.1 Software revisions 3
1.3.2 User Manual revision 3
2 Overview 4
2.1 Introduction to Marine Watch 4
2.2 Typical Installation 4
2.3 Components and Default IP Address 5
2.3.1 Main Panel 5
2.3.2 Subpanels 5
2.3.1 Annunciator Panels 6
2.3.2 I/O Cabinet 6
2.4 S-ONE Main Panel Emergency Switchover 6
2.5 S-ONE Alarm Panel 7
2.5.1 Hardware Connections 7
2.5.2 Operator Interface 8
2.5.3 3rd Party Communication Interface 8
2.6 S-ACE Annunciator Panel 9
2.6.1 Hardware Connections 9
2.6.2 Operator Interface 9
2.7 Output Signals 9
3 The S-ONE User Interface 10
3.1 Header Information 10
3.1.1 Header Status Symbols 10
3.2 The Switch Channel Page 11
3.2.1 Channel Status 12
3.3 The Analog Channel Page 13
3.3.1 Channel Status 14
3.4 The Output Channel Page 16
3.5 Screen Navigation 16
4 The S-ONE Main Menu 17
4.1 Quick Controls 17
4.1.1 Display 17
4.1.2 Home Page 18
4.1.3 Grouped Channels 18
4.1.4 Panel Language 18
4.1.5 Buzzer 19
4.2 Display 19
4.2.1 Brightness 20
4.2.2 Mode 20
4.2.3 Theme 20
4.2.4 Clean Screen 20
4.2.5 Sparkline 21
4.2.6 Date & Time 21
4.2.7 Screensaver 21
4.3 Event Log 22
4.4 Troubleshooting 23
4.4.1 This Panel 23
4.4.2 System Status 23
4.4.3 I/O Cabinet 24
4.4.4 Subpanel 24
4.5 Administration 25
4.5.1 This Panel 25
4.5.2 I/O Cabinet 25
4.5.3 Administration Menu 25
5 The S-ONE Administration Menu 27
5.1 This Panel 27
5.1.1 Panel Type 27
5.1.2 Timestamped Events 28
5.1.3 Configuration Data 28
5.1.4 Maintenance 28
5.1.5 Network 29
5.1.6 Panel Name 29
5.1.7 Disable & Acknowledge 30
5.2 I/O Cabinet 31
5.2.1 Network 31
5.2.2 Type 32
5.3 Switch Channels 33
5.4 Analog Channels 34
5.5 Output Channels 36
5.6 Group Channels 37
5.7 NFC Devices 38
6 The S-ACE Annunciator Panel 39
6.1 Buttons 39
6.2 Header Information 39
6.3 Header Status Symbols 40
6.4 Alarm View 40
6.5 Menu 41
6.5.1 Main Menu 42
6.5.2 Administration Menu 44
7 I/O Cabinet Connections 47
7.1 Power Supply 47
7.1.1 Ground 47
7.2 Ethernet Communication 47
7.3 Switch Channels 47
7.4 Analog Channels 48
7.5 Output Channels 48
7.5.1 Standard Output Channels 48
7.5.2 Optional Output Channels 49
7.6 Alarm Panel Supply 49
Page 2 (49)

1 About this manual
1.1 Intended audience
This manual has been published primarily for professionals and qualified personnel. The
user of this material is assumed to have basic knowledge in marine systems and must be
able to carry out related electrical work.
1.2 Responsibilities
It is the sole responsibility of the installer to ensure that the installation work is carried out
in a satisfactory manner, that it is operationally in good order, that the approved material and
accessories are used and that the installation meets all applicable rules and regulations.
All information in this manual is based upon information at the time of printing. For updated
information, please contact your local distributor.
1.3 Revisions
This manual is valid for the latest software version of the Marine Watch S Series Alarm
Panel.
1.3.1 Software revisions
● See this document for S-ONE Alarm Panel software revisions.
● See this document for S-ACE Annunciator Panel software revisions.
1.3.2 User Manual revision
User manual revision: December 2020
Page 3 (49)
Work on the low-voltage circuit should only be carried out by qualified and
experienced personnel.
Installation or work on the shore power equipment must only  be carried out by
electricians authorized to work with such installations.
Auto-Maskin continuously upgrades its products and reserves the right to make
changes and improvements without prior notice.
The crossed-out wheeled bin symbol indicates that the item should be
disposed of separately. The item should be handed in for recycling in
accordance with local environmental regulations for waste disposal.
By separating a marked item, you will help reduce the volume of waste
sent to incinerators or land-fill and minimize any potential negative impact
on human health and the environment.

2 Overview
2.1 Introduction to Marine Watch
The Marine Watch S Series is a sophisticated and powerful alarm system, designed to be
easy to set up and use.
The S-ONE Alarm Panel touch screen displays binary events as rectangles, where each
rectangle represents the status of a channel. Analog channels are represented with gauges.
In the event of a warning or an alarm, the corresponding rectangle indicates clearly with a
flashing behavior, and the buzzer sounds. An operator can acknowledge the event by
touching the rectangle.
Additional S-ONE Alarm Panels can be added in the network, and these are designated
Subpanels. Finally, several S-ACE Annunciator Panels can be added in the network.
All I/O interfaces are built into a separate I/O Cabinet. The communication between the
Alarm Panel and the I/O Cabinet is on standard Ethernet.
2.2 Typical Installation
The typical Marine Watch installation consists of one or several I/O Cabinets, one or several
S-ONE Alarm Panels, and a few S-ACE Annunciator Panels. All units are connected on a
standard Ethernet network.
Page 4 (49)

Additional S-ONE and S-ACE panels can be added at any time, and requires no change in
the overall configuration. One must only make sure there is no IP address conflict.
The S-ONE Alarm Panel can be used as either the Main Panel or a Subpanel.
2.3 Components and Default IP Address
All Marine Watch S Series’ components have a factory-default IP address. If more than one
of each type of component is in use, then make sure to change the IP address of the extra
component.
No two components in the network shall have the same IP address.
1 From the factory, the IP address on the Subpanel is the same as for the Main Panel. This must be
changed to be unique.
Page 5 (49)
2.3.1 Main Panel
One of the S-ONE alarm panels shall in the
configuration be designated the Main Panel. This is the
default setting.
The Main Panel shall be configured and holds the
entire system configuration. Configuration is done in
the Administration submenu.
It can be done manually using the menu interface or by
loading a predefined configuration file.
Default IP address: 192.168.0.151
2.3.2 Subpanels
Additional S-ONE alarm panels can be added in the
network, and these are called Subpanels. It must be
configured as such, under Panel Type in the
Administration menu.
Each Subpanel replicates the Main Panel and
optionally has specific use cases.
A Subpanel is automatically always in sync with the
Main Panel configuration.
Default IP address: 192.168.0.151
1
Configuration changes are automatically also applied to all networked
Subpanels and Annunciator panels.

2.4 S-ONE Main Panel Emergency Switchover
In the unlikely event of a Main Panel failure, any Subpanel can act as a replacement panel,
and quickly be reconfigured to be a Main Panel.
Make the system operative again:
1. Remove the Ethernet cable from the faulty Main Panel.
2. In the Administration menu of the desired replacement panel, select
This Panel > Panel Type: Select Main Panel.
3. In the same administrative page, take note of the replacement panel IP address.
Reconnect any other Subpanels and Annunciator Panels.
4. If the Marine Watch S system consists of additional S-ONE Subpanels or S-ACE
Annunciator Panels, they need to be reconfigured. In the Administrative menu,
select I/O Cabinet > Network: Enter the replacement panel IP address.
2 If several S-ACE Annunciator Panels are in use, then make sure all IP addresses are unique.
3 If several I/O Cabinets are in use, then make sure all IP addresses are unique.
Page 6 (49)
2.3.1 Annunciator Panels
Several S-ACE annunciator panels can be added in the
network.
An annunciator panel is automatically always in sync
with the S-ONE Main Panel configuration.
Default IP address: 192.168.0.201
2
2.3.2 I/O Cabinet
The I/O Cabinet is the sensor hub. It collects all sensor
data and makes it available to the Marine Watch
Panels.
The I/O Cabinet is available in different sizes,
I/O-capacities, and I/O type.
There can be up to four I/O cabinets in the network.
Default IP address: 192.168.0.11
3
Make sure that there is only one Main Panel in the Marine Watch S system.

2.5 S-ONE Alarm Panel
2.5.1 Hardware Connections
The rear side of the S-ONE Alarm Panel has the following interfaces.
Connection Interfaces
* not supported
Cable Strain Relief
Make sure the following cables are tied with wire wrap to the strain relief eyes on the back
panels.
■ Ethernet cables
■ HDMI cables
■ USB cables
Page 7 (49)
6. NMEA 2000* (isolated)
7. Ethernet 1 RJ45*
8. Ethernet 2 RJ45 (for network communication)
9. 2x USB-A
10. USB-A
11. HDMI out*
1. CAN bus*
2. Relay*
3. Modbus RTU*
4. Flexible I/O*
5. Power supply 12 V / 24 V
Connectivity
Power Supply
12 V / 24 V
USB
USB 2.0 High-speed interface
Reserved for software update, event log extraction, and configuration file
handling.
Ethernet 2
RJ45. Used for networking.
Miscellaneous
Buzzer
Activates for any new event.
Ambient Light Sensor
Automatically adjustment of screen brightness.
Proximity Sensor
Motion detection.

2.5.2 Operator Interface
In addition to the touch interface on the screen, there are buttons on the right-hand side of
the panel. These are used to control different parts of the panel as described below:
2.5.3 3rd Party Communication Interface
Other systems can interface the S-ONE Alarm Panel using the built-in Modbus TCP
interface on Ethernet.
The communication I/O list can be found here: http://tiny.cc/zxxebz
Page 8 (49)
Interface
Power Indication
Lit when the panel is powered.
NFC Sensor
Not used in this software revision.
Home Button
Toggles the Alarm and Menu page, and
the optional Home page.
Alarm Button
Silence the buzzer or advance to the next
page with events.
Brightness Increase Button
Increase screen brightness.
Brightness Decrease Button
Decrease screen brightness.

2.6 S-ACE Annunciator Panel
2.6.1 Hardware Connections
In order to achieve full IP-56 ingression support, the unused connectors must be populated
with sealing plugs.
2.6.2 Operator Interface
In addition to the touch interface on the screen, there are buttons on the right-hand side of
the panel. These are used to control different parts of the panel as described below:
2.7 Output Signals
Marine Watch includes a standard set of output signals in the I/O Cabinet. See the chapter
for the I/O Cabinet for further details.
Page 9 (49)
Required Connectivity
Description
Connector
Power
C1.11: 24 V
C1.12: 0 V
Ethernet
RJ 45
USB
USB-A
Symbol
Button
Action
Home Button
Toggles the Alarm and Menu page.
Alarm Button
Silence the buzzer and display the Alarm View.
Optional operator-controlled outputs can be added to the I/O Cabinet.

3 The S-ONE User Interface
3.1 Header Information
The header consists of the following information.
■ The Auto-Maskin logotype.
■ The Panel is named Marine Watch. The name can be changed in the configuration.
■ A common warning/alarm banner. The entire center of the header is flashing for new
unacknowledged events. It is solid lit for acknowledged events.
■ Various status symbols.
■ The Time can be displayed as an option.
3.1.1 Header Status Symbols
These symbols may appear in the header bar.
4 The red alarm banner takes precedence over the yellow warning banner
Page 10 (49)
At least one channel
indicate Alarm
At least one channel
indicate Warning
At least one Alarm and
at least one Warning
The buzzer is disabled
by the operator
One or more channels
are disabled by the operator
At least one new
Alarm or Warning
4

3.2 The Switch Channel Page
There will be one or several pages with rectangles. This is dependent on the configuration,
the number of connected I/O Cabinets, and the type of I/O in each Cabinet.
Each rectangle represents the status of one switch input channel, and each page can
display status from up to 60 channels.
Channels can optionally be assigned to one of three different groups, and the group can be
given a name and assigned a group-color.
Different alarm panels can be configured to indicate and allow acknowledgment for select
groups of channels only.
Page 11 (49)

3.2.1 Channel Status
Each rectangle represents the status of a binary channel as follows.
Page 12 (49)
Status
Description
Sample Graphic Representation
Normal
The channel is not
alarming.
Active and not
acknowledged
The channel is
alarming, following its
persistence timer.
Text in bold, flashing.
Active and
acknowledged
The channel is
acknowledged by an
operator and will clear
when the alarm clears.
Regular text.
Inactive and not
acknowledged
The channel has
activated but is not
active now.
It will clear when
acknowledged.
Grey background, bold
flashing text in
yellow/red.
Disabled
The channel has been
disabled by an
operator.
The rectangle is
reduced in size and
grey.
Disabled, but
active event
The channel has been
disabled by an
operator.
Border in severity color
if the channel is active.

3.3 The Analog Channel Page
The analog page can display up to eight channels in a 4 x 2 grid. Each channel is
represented as a circular gauge or as a bar graph widget. An optional Sparkline can be
displayed.
A maximum of two analog pages can be displayed, holding a maximum of 16 analog
channels.
Page 13 (49)
Analog channels are an option. If the I/O Cabinet does not include the analog
option, then these pages are not displayed.
Widget Properties
Name
The analog signal description.
Value
Real-time value scaled between the sensor Min-Max value in the
configuration. An out-of-limit value is indicated with “---”.
Unit
The signal unit.
Min/Max Range
Instrument Min/Max values.
Alarm Limits
LL | L | H | HH
Sparkline
Optional sparkline for up to 1 hour of operation.

3.3.1 Channel Status
Page 14 (49)
Status
Description
Sample Graphic Representation
Normal
The channel is not alarming.
Active and not
acknowledged
The channel is alarming,
following its persistence timer.
Instrument text in bold,
flashing.
Active and
acknowledged
The channel is acknowledged
by an operator and will clear
when the alarm clears.
Regular instrument text.
Inactive and not
acknowledged
The channel has activated but
is not active now.
It will clear when
acknowledged.

Page 15 (49)
Disabled
The channel has been
disabled by an operator.
Disabled, but
active event
The channel has been
disabled by an operator and is
indicating an event.

3.4 The Output Channel Page
The panel can be configured to display up to 16 operator switches on one page.
Note that the I/O Cabinet must have the optional output modules. The output channels can
be configured to either toggle or momentary. Only the Main Panel can control the outputs.
3.5 Screen Navigation
This is how to operate and navigate the panel.
Page 16 (49)
Action
Do this
Acknowledge an
event
Tap the event widget. The event widget is
■ the rectangle - for binary/switch channels
■ the circular gauge or bar graph - for analog channels
Disable Channel
Push and hold the corresponding widget for one second.
Next Screen
Swipe left on the screen.
Previous Screen
Swipe right on the screen.

4 The S-ONE Main Menu
The Main Menu is always available to the operator. It is divided into several sections as
follows.
4.1 Quick Controls
Whenever the Main Menu is accessed, it always displays the Quick Controls section. These
settings are used most frequently.
4.1.1 Display
Page 17 (49)
Brightness
Brightness slider
Manually adjust the backlight brightness.
Auto
The backlight brightness is adjusted automatically.
Note! Using the physical buttons to change the brightness will override this
setting and set Auto to Off.
Mode
Day
Colors optimized for daylight.
Night
Colors optimized for use in dark environments.
Auto
Switches automatically between Day and Night modes.

4.1.2 Home Page
The Home Page is an optional overview of all the pages and makes it easy to navigate to
any page from here.
Events are summarized per page, and disabled channels are indicated.
The Home Page is divided into three rows, switch channels, analog channels, and output
channels.
4.1.3 Grouped Channels
If a channel is assigned to a group, it can be indicated with a colored rectangle and an
optional group name. It is possible to assign each channel to one of three different groups.
By default, a channel does not belong to any group.
4.1.4 Panel Language
Select the preferred panel language.
Page 18 (49)

4.1.5 Buzzer
4.2 Display
Page 19 (49)
Panel Buzzer
Off
Silenced.
Low
50 % volume.
Normal
100 % volume.
Panel Buzzer Pattern
Standard
Standard on / off pattern.
Annoying
Four quick beeps.
Touch Feedback
Off
Silenced.
Low
50 % volume.
Normal
100 % volume.

4.2.1 Brightness
4.2.2 Mode
4.2.3 Theme
4.2.4 Clean Screen
Page 20 (49)
Brightness
Brightness slider
Manually adjust the backlight brightness (0-100%).
Auto
The backlight brightness is adjusted automatically.
Note! Using the physical buttons to change the brightness will set Auto to
Off.
Mode
Day
Colors optimized for daylight.
Night
Colors optimized for use in dark environments.
Auto
Switch automatically between Day and Night modes.
Theme
Day Mode
Choose a color representation for use in Day mode
Night Mode
Choose a color representation for use in Night mode
Clean Screen
Clean Screen
Displays the screen in all-black so fingerprints are clearly visible and can
be wiped off with a soft cloth.
Press the button on the screen to exit.