auto maskin Marine Pro 200 Series User manual

April 10, 2019 (1.1)
Publication P/N: 1100409
Copyright © Auto-Maskin AS, 2019
User Interface Basics
The screen pages and panel buttons shown below are presented as
they will appear on an attached RP 210/220E Remote panel.
What‘s in the Box?
Instrument Pages
Configurable Gauges
and Bar-graphs.
Select Page
Thumbnails for quick
selection.
Home & Alarm
buttons located at the upper
right side of the panel.
Start & Stop Engine
buttons located at the lower
right side of the panel.
Alarm List
Red: Alarms/Shutdowns
Yellow: Warnings
White: Other messages
Bold: Unconfirmed
Menu
This page displays the Menu
hierarchy.
For More Information:
For the latest updated information, please contact your local
distributor or visit the Marine Pro 200 section of the Auto-Maskin
web site: http://www.auto-maskin.com
1. DCU 208E in an ESD Bag
2. Quick Installation Guide
Quick Installation Guide
DCU 208E
P/N 1006477
Caution!
Handle with care when opening
the bag and installing the unit.
Engine Monitor and Control Unit
19 flexible configurable
channels for either
digital input, digital
output, 4-20 mA or 0-5V
input.
2 thermistor input
channels
Dual J1939 interfaces
1 magnetic pickup
channel
Ethernet and Modbus
communication
DIN rail mounting clips

April 10, 2019 (1.1)
Publication P/N: 1100409
Copyright © Auto-Maskin AS, 2019
Specifications
Installation Steps
Configuration Steps
Measurements
Section
Width
Height
Depth
Unit
Size
163
131
75
mm
Power Ratings
Section
Min
Typ.
Max
Unit
Power
Supply, Vcc
8
-
12/24
0.5
32
2
VDC
A
Max ripple 10% without exceeding Min and Max values.
Connectors
USB
RJ45,
Ether-
net
C1:
Power
CAN,
RIO,
IO1-4
C2:
Relay1,
Relay2,
AllFaults,
IO5,20,21
C3:
IO6-17
C4:
MPU,
RS-485,
Therm1&2
IO18,19
1. Remove the unit from the ESD Bag.
2. The unit comes with DIN-Rail mounting clips
for easy snap clips on the rear side of the
unit.
3. Attach the Power Supply connector (CON1)
and make sure the power ratings are within
product specifications.
4. Connect additional external connectors
(CON2-4) according to specification related to
the applicable application. This may include
the following:
* CAN bus (J1939)
* All Faults
* Switch Inputs
* Magnetic Pickup
* PT 100 Sensors
* 4-20 mA Sensors
* RIO Link
5. For improved sealing use a RJ45 connector
cap.
A Connector Kit (P/N: 1006479) with four
Deutsch DT-connectors, crimp sockets and
sealing plugs is available. See the Installation
Manual for further information.
The DCU has a built in web server with access to
a full configuration of the unit.
PC Connection/Setup:
Connect via Ethernet using a Net Browser
From the Address Field in the Browser, type
the IP-Address. Factory Default is
192.168.0.101.
Then log in to the unit. Factory Default
Username is ‘DCU’ and Factory Default
password is ‘1234’.
For further details and information, please see
the Configuration Manual.
Responsibilites:
It is the sole responsibility of the installer to ensure that the
installation work is carried out in a satisfactorily manner and
meet all applicable rules and regulations.
Note:
Auto-Maskin continuously upgrades its products and reserves
the right to make changes and improvements without prior
notice.
Additional Documentation:
Please visit the Marine Pro 200 section of the Auto-Maskin
web site for the following enhanced documentation:
Installation Manual
Configuration Manual
User’s Manual.
http://www.auto-maskin.com