Nexus Wind Data User manual

0
Installation and Operation Manual

1
Introduction
Thank you for choosing Nexus Wind Data instrument. We are convinced that you will
appreciate all the valuable information either you are a cruiser or a racer. It is important
that you are following this instruction regarding installation and operation.
If the instrument are to be used in a Nexus Network, there are some systems settings that
are dependent on where the transducers are installed, i.e. at the instrument or at the
Server.
This manual is written for Nexus Wind Data instrument version 1.00
Edition: June 2000
INTRODUCTION

2
1 Part specifications............................................................................................................4
2 Installation........................................................................................................................6
2.1 Installing the instrument...........................................................................................7
2.2 Installing cable.........................................................................................................8
2.3 Connections in Nexus Network.................................................................................8
2.4 Connection of log transducer....................................................................................9
3 First start (only in a Nexus Network)............................................................................... 10
3.1 Initialising the instrument........................................................................................ 10
3.2 Re-initialising the instrument.................................................................................. 10
4 Operation....................................................................................................................... 11
4.1 About this manual.................................................................................................. 11
4.2 How to use the 4 push-buttons............................................................................... 12
4.2.1 MODE................................................................................................................. 12
4.2.2 DOWN................................................................................................................ 12
4.2.3 UP ...................................................................................................................... 12
4.2.4 KEY.................................................................................................................... 12
4.2.5 Clear................................................................................................................... 13
4.2.6 Calibration .......................................................................................................... 13
4.2.7 Lighting............................................................................................................... 13
4.3 Main function ......................................................................................................... 14
4.4 Analogue function .................................................................................................. 14
4.5 Sub-functions......................................................................................................... 15
4.5.1 Apparent Wind Speed [AWS] .............................................................................. 15
4.5.2 True Wind Speed [TWS] ..................................................................................... 15
4.5.3 True maximum Wind speed................................................................................. 15
4.5.4 Velocity Made Good (VMG)................................................................................. 15
4.5.5 Battery voltage [BAT], option............................................................................... 16
4.5.6 Boat speed [BSP], option..................................................................................... 16
4.5.7 Trip log [TRP], option.......................................................................................... 16
4.5.8 Water temperature [TMP], option......................................................................... 16
4.5.9 Trim function for optimum Wind angle or speed, option....................................... 16
4.6 More Wind Data functions Nexus Network.............................................................. 18
4.6.1 Geographic Wind direction (TWD)....................................................................... 19
4.6.2 WCV, Waypoint Closing Velocity......................................................................... 19
4.6.3 X-track error, XTE............................................................................................... 19
4.6.4 HDC / NXT, Course after tack or jibe................................................................... 21
4.6.5 BTW / NXT, Bearing and angle deviation relative next course.............................. 22
5 Calibration...................................................................................................................... 24
5.1 C10 User settings................................................................................................... 24
5.1.1 C11 Select the dampening................................................................................... 24
5.1.2 C12 Select main information ............................................................................... 24
5.1.3 C13 Displaying boat speed, trip log and temperature, option................................ 25
5.1.4 C14 Display NAV functions, option...................................................................... 25
5.1.5 C15 Beep when key is pressed............................................................................ 25
5.2 C20 Calibration of Log ........................................................................................... 25
5.2.1 C21 Select unit for speed .................................................................................... 25
5.2.2 C22 Calibration of log transducer ........................................................................ 25
5.2.3 C23 Unit for temperature..................................................................................... 26
5.2.4 C24 Temperature offset....................................................................................... 26
5.3 C30 Compass Settings........................................................................................... 26
CONTENTS

3
5.3.1 C31 True or magnetic course .............................................................................. 26
5.3.2 C32 Magnetic deviation....................................................................................... 26
5.3.3 C33 Reference for Compass, static or GPS......................................................... 26
5.4 C50 Wind Settings................................................................................................. 27
5.4.1 C51 Network setting of true or apparent Wind angle............................................ 27
5.4.2 C52 Unit for Wind speed..................................................................................... 27
5.4.3 C53 Wind speed calibration................................................................................. 27
5.4.4 C54 Adjustment of Wind angle............................................................................ 27
5.4.5 C55-C62 Calibration table for the Wind transducer.............................................. 27
5.4.6 C63 Speed reference, water or GPS.................................................................... 28
5.4.7 C64 Wind trim reference ..................................................................................... 28
5.4.8 C68 Roll adjustment............................................................................................ 28
5.4.9 C69 Pitch adjustment.......................................................................................... 28
5.5 C70 Configure Nexus............................................................................................. 28
5.5.1 C71 Wind-master................................................................................................ 29
5.5.2 C72 Log-master.................................................................................................. 29
5.5.3 C73 Function on terminal In3 .............................................................................. 29
5.5.4 Connection of trim button.................................................................................... 29
5.5.5 C74 Demo mode................................................................................................. 30
6 Maintenance and fault finding......................................................................................... 31
6.1 Maintenance .......................................................................................................... 31
6.2 Fault finding........................................................................................................... 31
6.2.1 General............................................................................................................... 31
6.2.2 Fault - action....................................................................................................... 32
6.2.3 Error messages................................................................................................... 32
7 Specifications................................................................................................................. 33
7.1 Technical specifications ......................................................................................... 33
7.2 Nexus data bus introduction and user policy........................................................... 33
8 Optional Accessories...................................................................................................... 35
9 Abbreviations ................................................................................................................. 37
10 Warranty................................................................................................................. 36
CONTENTS

4
1Part specifications
Nexus Wind Data is delivered with all parts for mounting. Check prior to
installation.
Wind Data instrument
Qty. Description Reference
1Instrument, Nexus Wind Data 1
1Instrument front cover 2
1Drill template 3
1Installation and user manual 4
1Warranty card 5
1National distributors list 6
1Power cable, red and black, 3 m (9 ft) 7
5Extra wire protectors, 0,25 mm (1/100”) 8
5Extra wire protectors, 0,75 mm (1/32”) 8
4Mounting screws for the instrument 9
4Round rubber covers 9
1Tube of silicon grease 9
1Connection cover 9
24-pol screw terminal 9
Additional in Wind Data complete with transducer
1Wind transducer Nexus 10
1Mast top cable. 25m (83 ft) 11
3Mounting screws for mast bracket 12
1Mast head bracket 13
Registering of this product
Once you have checked that you have all the listed parts, please take
time to fill in the warranty document and return it to your national
distributor.
By returning this document, it will assist your distributor to give you
prompt and expert attention, in the event of your experiencing difficulties
with this product. Keep your proof of purchase. Also, your details are
added to our customer database so that you automatically receive new
product catalogues as and when they are released.
PART SPECIFICATIONS

5
PART SPCIFICATIONS

6
1Installation
You can install the Nexus Wind Data in three different ways:
•The wind transducer is connected directly to the Nexus Wind Data
instrument
•By using the connection kit when both log and wind transducers are
installed with a single Wind Data.
•The installation may also include a Nexus Server where all transducers
may be connected. All data including power will pass along one cable.
•The installation includes 6 major steps:
1. Read the installation and operation manual.
2. Plan where to install the transducers and instruments.
3. Run the cables.
4. Install the transducers and instruments.
5. Take a break and admire your installation.
6. Learn the functions and calibrate your system.
Before you begin drilling ... think about how you can make the installation
as neat and simple as your boat will allow. Plan where to position the
transducers, Server and instruments. Think about leaving space for
additional instruments in the future.
•A few ”do nots” you should consider:
−Do not cut the cables too short. Allow extra cable length at the Server so
it can be disconnected for inspection without having to disconnect all
attached cables.
−Do not place sealant behind the display. The instrument gasket
eliminates the need for sealant.
−Do not run cables in the bilge, where water can appear.
−Do not run cables close to fluorescent light sources, engine or radio
transmitting equipment to avoid electrical disturbances.
−Do not rush, take your time. A neat installation is easy to do.
•The following material is needed:
Wire cutters and strippers.
Small and large Philips and small flat head screw driver.
Hole saw for the instrument clearance hole 63 mm (2½").
2.8 mm (7/64") drill for the mounting holes in wood.
3.2 mm (1/8") drill for the mounting holes in fibre glass.
Plastic cable ties
If you are doubtful about the installation, obtain the services of an
experienced technician.
The warranty is not valid if you have damaged the instrument by
drilling through the front mounting holes.
2: INSTALLATION

7
1.1 Installing the instrument
•Place the adhesive drill template on the desired location for the
instrument. Drill the 4 screw holes using a 2.8 mm (7/64") drill for wood or
3.2 mm (1/8") for fibre glass. Use a 63 mm (2½") hole saw to machine the
clearance hole for the instrument connection socket. Remove the
template.
Note: Never drill through the instruments 4 mounting holes as the
gaskets may be damaged and thus cause leakage. The warranty is
not valid for damage caused by drilling through the mounting holes.
•Run the Nexus Network cable from the Server to the instrument.
•Cut the Nexus Network cable to length. Peel off about 35 mm (1,4") of the
cable insulation. Remove about 6 mm (1/4") from the 3 isolated wires
(the 4th wire is an earth / screen). Attach the 4 cable protectors to the
wires using a pair of flat pliers.
•Connect the 4 cable protectors to the 4-pole jack plug as shown. Apply
silicon paste on all locations as shown.
Note: Must be done to avoid corrosion.
•Apply silicon paste to the instrument connection pins at the back of the
instrument. Press the jack plug onto the instrument pins. Press down the
cable in the cable leads. Mount the connection back cover with the screw.
•Mount the instrument in the pre-drilled position.
Note! Use all 4 screws, and tighten the screws (in cross pattern) so
the gasket will be evenly compressed to 1/3 of its original thickness.
Very important for a correct sealing to avoid leakage!
•Press on the 4 rubber caps to seal and hide the mounting screws.
Your instrument installation is done!
Silicon paste
Silicon paste
2: INSTALLATION

8
1.2 Installing cable
The power cable is connected via a 3A fuse from the battery or at the
boats fuse panel and direct to the instrument or Server. One red and one
black power wire is included. Note, set C71 On (see 5.5.1)
Always connect a 3 AMP fuse between Power supply and
instrument.
1.3 Connections in Nexus Network
If you already have a Nexus Network i.e. a Server, it is more practical to
connect the transducer to the Server due to the single instrument cable
installation. Note, set C71 OFF (see 5.5.1)
The instrument is then connected to the Server’s Nexus Network terminal
(pin 5, 6, 7 and 8) or any instrument .
Server
Transducer
3A Fuse
Black
Screen
Red
Green Yellow
White
2: INSTALLATION

9
1.4 Connection of log transducer
If you have an other log instrument i.e. a Nexus log, a Star log, a D-20
log, a 2200 log or a 220 log, you may connect the single log pulse wire
from that instrument to the Wind Data instrument terminal 4.
If you don’t have a log instrument, but want to install a log transducer,
use the connection box (Art. no: 21453 ).
From log transducer,
NEXUS, Star, D-20,
2200 or 220
3A Fuse
2: INSTALLATION
From Server or other
NEXUS instrument

10
2First start (only in a Nexus Network)
2.1 Initialising the instrument
At power on, the instrument will perform a self test. The display will first
show all segments, then the software version number and the Nexus
Network ID number.
At first power on after installation, you will be asked to press KEY
[PrSKEY]. This will give the instrument a logical ID number on the Nexus
Network.
To initialise the instrument, press KEY on all installed digital instruments,
one at the time.
Note: Always wait for the text ”Init OK”
to be displayed, before you press KEY
on the next instrument!
The Server automatically gives the first unit ID number 16, then 17 and
so on. The order in which you press KEY is the same order as the
instruments will be given a logical ID number on the Nexus Network.
The example shows that the instrument version number is 1.00 and the
given logical ID number is 16.
2.2 Re-initialising the instrument
If two instruments by mistake have the same ID number, this can cause
disturbance and block the information on the Nexus data bus.
To re-initialise the instrument, press DOWN and UP together during the
power up sequence when version and ID numbers are displayed.
The display self test is then re-started on all instruments and you will be
asked to press KEY on each instrument as explained above.
Note! If you do not succeed to re-initialise, we suggest you disconnect all
but one instrument with the same ID number, then repeat the above
procedure.
3: FIRST START

11
3Operation
3.1 About this manual
•Each time a push-button are referred to in this manual, the push-button
name will appear in bold and CAPITAL letters, e.g. MODE.
•Unless otherwise stated, the push-button presses are momentary.
•Each time a function is mentioned in the text, it will be in brackets and in
the same format, where possible, as displayed, e.g. [AWA].
•This manual has been written to be: Compatible with Wind Data
instrument from software version 1.0.
•All functions followed by the text option is not valid in a factory set-up
instrument. See calibration to be able to display these functions.
Note!
We have put down a lot of effort in order to make this manual correct and
complete. But since we continuously make our products better, some
information can differ from the products functions. If you need further
information contact your national distributor
4: OPERATION

12
3.2 How to use the 4 push-buttons
3.2.1 MODE
A press on MODE change the mode of the graphical display. It scrolls in
a circular pattern, one step for every press.
The MODE button is also used to move the cursor when in edit mode. A
press on MODE moves the cursor in a circular pattern, one step to the
right for every press.
A press on MODE and DOWN together, back steps cursor to the
preceding step.
When in editing mode a long press (>2sec) on MODE will escape from
that editing mode.
3.2.2 DOWN
A press on DOWN moves to the next sub-function.
In edit mode it decreases to previous digit.
3.2.3 UP
A press on UP moves to the previous sub-function.
In edit mode it increases to next digit.
3.2.4 KEY
A press on KEY unlocks a digit to access edit mode.
When unlocked, the digits are ”active” (flashes) and can be edited by
pressing DOWN, UP and MODE as required.
When finished editing, lock the digit by another press on KEY.
4: OPERATION
MODE DOWN UP KEY
APPARENT
WIND ANGLE
TRUE
WIND ANGLE
TRIM
FUNCTION
MAIN
FUNCTION
INFOTEXT
SUB-
FUNCTION

13
3.2.5 Clear
A press on DOWN and UP together, clear digits.
3.2.6 Calibration
To access calibration mode, press and hold KEY more than 2 seconds.
To return to main function mode, press KEY when the text return [RET] is
shown.
3.2.7 Lighting
The instrument uses red back lighting for the display and the 4 push-
buttons. The lighting can be set at 4 different levels.
To access the light control, press and hold MODE for more than 2
seconds. The flashing text [Lit OFF] will be displayed and the display will
be lit momentarily.
To select between the 4 light levels, press UP: [LOW], [MID], [MAX] and
[OFF]. To lock the selected level, press KEY.
The selected light level will be copied to all Nexus instruments connected
to the system. When the lighting is on, it is not possible to reduce or turn
off the lighting on an individual instrument.
4: OPERATION

14
3.3 Main function
Top data is relative Wind angle, [AWA] (Apparent Wind Angle). As an
alternative to [AWA] the following can be displayed:
[AWS] (Apparent Wind Speed).
[TWA] (True Wind Angle) if the log transducer is connected.
[TWS] (True Wind Speed) if the log transducer is connected.
To change between these functions, see C12, 5.1.2.
3.4 Analogue function
Change Wind scale between 180°° and 60°° with MODE . Selected scale
is shown with the LCD arrow pointing at scale.
The text [APP] displays selected main function as apparent Wind angle
or Wind speed.
MIX 180°° The text MIX 180° means that both APP and TRUE Wind
angle is displayed in scale 180°.
MIX 60°° The text MIX 60° means that both APP and TRUE is
displayed in scale 60.
The scale can be altered between 60° and 180° to get more accurate
readings. At scale 180° each sector represent 5° and at scale 60° each
sector represent 1 2/3°. See the example below .
4: OPERATION
WIND

15
3.5 Sub-functions
Select sub-function with UP or DOWN.
Information text for the sub-function is displayed. You may also ”park”
your favourite function so it will automatically be displayed after power
on.
Press both MODE and KEY to ”park” the displayed function. The display
will flash once to confirm that you have ”parked” the function.
3.5.1 Apparent Wind Speed [AWS]
The text [AWS] (Apparent Wind Speed) and its value is displayed below.
The text [AWS] is toggled with the text [KTS] (KnoTS), [M/S] (Metres/S)
or [BF] (Beaufort).
3.5.2 True Wind Speed [TWS]
The text [TWS] (True Wind Speed) and its value is displayed below.
The text [TWS] (True Wind Speed) is toggled with the text [KTS]
(KnoTS), [M/S] (Metres/s)or [BF] (BeauFort).
3.5.3 True maximum Wind speed
Press the KEY in the sub-function: [TWS] to display maximum true Wind
speed. After 5 seconds the display will go back to [TWS] again.
Re-set or clear the [MAX] Wind speed value by pressing UP and DOWN
together or switch off the power.
3.5.4 Velocity Made Good (VMG)
The text [VMG] (Velocity Made Good) is
displayed with the actual boat speed towards or
against the Wind.
The water speed information from the log
transducer is needed. The speed information
can be taken from the log transducer or from
Nexus Network. VMG = 0.0 knots when the true
Wind angle is perpendicular to the boat.
4: OPERATION
WIND

16
3.5.5 Battery voltage [BAT], option
The text [BAT] will display battery voltage. The voltage is measured
inside the instrument and will not compensate for any voltage drop
caused by installation.
3.5.6 Boat speed [BSP], option
The text [BSP] will display boat speed (water speed). The text [BSP] will
toggle with selected unit, i.e. (KTS), (KMH) or (MPH).
As an option, you may add or remove displaying boat speed [BSP],
trip log [TRP] and water temperature [TMP]. See further under
calibration.
3.5.7 Trip log [TRP], option
The text [TRP] is displayed and will show trip distance from 0.00 to 99.9
nautical miles, kilometre or miles. After 99.9, 0.00 is displayed. Clear trip
by pressing UP and DOWN together.
3.5.8 Water temperature [TMP], option
The text [TMP] is displayed with water temperature in Celsius or
Fahrenheit.
This function require a Nexus or Star log transducer.
3.5.9 Trim function for optimum Wind angle or speed, option
The text [TRM] and [OFF] is displayed when this function is off. The trim
function can be used as an aid to keep the correct tacking angle or to
discover speed changes caused by sail or rig trimming. Some of the
functions can only be used when the Wind Data is connected to Nexus
Network.
As the first example we will use [TRM AWA] (TRiMApparent Wind
Angle).
To trim on Wind angle deviation, select the text:
Press UPand DOWN together, the display will flash. Select [AWA] with
DOWN and confirm with KEY.
4: OPERATION

17
Select the level of dampening [d0-d9] and confirm with the KEY.
The default (or latest used) Wind angle is displayed. You may accept the
proposed angle by pressing the KEY or enter a new Wind angle with UP,
DOWN and MODE before confirming with KEY.
The entered Wind angle will be lost when power off. You may however
select a default Wind angle in set-up. See C64 5.4.7.
Every time you select this function, or after power up, the pre-set value is
proposed.
On the display you will see the text TRM and AWA toggling together with
your Wind angle. On the graphic part you will see your reference angle as
one straight horizontal segment when actual angle is equal to the pre-set
angle. At the same time you will see apparent and true Wind angle.
The deviation is displayed visible upwards or downwards from the
horizontal line to +/-15°. The maximum visible deviation is 15°. When the
deviation is between 15° and 30° the 15° sector is lit. When larger then
30° the segment sector is blanked out.
Trim on speed:
Select the trim function.
Press UPand DOWN together. Select text (BSP) by pressing UP and
confirm with KEY.
There is a number of different ”speeds” to be used for trimming. The
most common is [BSP] (Boat SpeeD) and [VMG] (Velocity Made Good).
The Wind Data instrument can also display deviation from optimum
calculated boat speed [TBS] or (Target Boat Speed).
The TBS is normally calculated by use of polar diagram on PC with
racing software. The value ”Target Boat Speed” is transmitted through
the Nexus Server on the NMEA 0183 input. The Server will then transmit
TBS on the Nexus Network.
On the Wind Data display you will see both the digital value in % and the
graphical value as a 2% variation for each segment.
You may select ”speeds” to TRIM, from this list:
BSP Boat speed Log transducer!
AWS Apparent Wind Speed
TWS True Wind Speed Log transducer!
SOG Speed Over Ground Navigator!
4: OPERATION
Each sector represents 2°

18
DRF Drift Log transducer + Compass +
Navigator!
WCV Speed towards a waypoint Navigator!
VMG Velocity Made Good Log transducer!
TBS Optimum speed based on polar diagram PC + NMEA 0183 through
Nexus Server!
OFF Function is OFF
When [BSP] (or other function) is selected, the dampening [d3] is
flashing. Select dampening level and confirm with KEY.
The text [% OFF] is then displayed to show that the function is selected,
but no reference is yet set.
Press KEY to set [BSP] reference.
The display will now show you the text [%] toggling with text [BSP] or
whatever trim you have selected.
The speed variation is expressed in % from set value.
Press the KEY every time you wish to set a new trim reference value.
There is an option to use an external trim button to set a new trim
reference. See more in the calibration.
3.6 More Wind Data functions Nexus Network
By adding (or using) the Wind Data instrument in the Nexus Network,
more functions will be added if the corresponding transducer is
connected.
The Wind Data functions may be added or removed by the user.
The Wind Data instrument can be used in a small Network together with
the Multi, Log or analogue instrument, without a Server.
In order to make the installation easy when using both log and Wind
transducer in a small Network we recommend you to install with
connection kit art.no. 21453. Only one cable will carry the signals to the
instrument, then there is one Network/power cable to the Multi or Log
instrument. (See 2.1.4).
When using the Wind Data in a bigger Network with more then 3
transducers, we recommend you to use the Nexus Server.
Only one cable will be used to connect all instruments. You will also have
the NMEA 0183 input/output.
If you need to be able to read the depth information on more then one
instrument, the Server is the only choice.
Network bonus function:
Each sector represents 2%
4: OPERATION