Automatic Technology Axess Pro Series User manual

Doc # 160027_01
Part # 13383
Released 05/03/14
Axess®Pro Series 3000
Industrial Roller Shutter Opener

2Axess Pro Series 3000 Owner Installation Instructions
Automatic Technology (Australia) Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all
conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of an
Automatic Technology (Australia) Pty Ltd industrial roller shutter opener. Automatic Technology (Australia) Pty Ltd hereby
further expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any
person as a result whether directly or indirectly from failure to install the Automatic Technology (Australia) industrial roller
shutter opener in accordance with these installation instructions.
WARNING: Electrical wiring must be in compliance with
your local building and electrical codes.
WARNING: It is vital for the safety of persons to follow
all instructions. Failure to comply with the installation
instructions and the safety warnings may result in serious
personal injury and/or property and remote control opener
damage. Please save these instructions for future reference.
NOTE: For full automatic operation a Safety Beam (Photo
Electric Beam Sensor) must be fitted to the logic console
with this opener. Failure to comply will void the warranty and
may cause serious personal injury and/or property damage.

Owner Installation Instructions Axess Pro Series 3000 3
1. Axess®Pro Series 3000 Contents
1-Phase 240Vac and 3-Phase 415Vac Industrial Roller Shutter Opener
1. Axess®Pro Series 3000 Contents 3
2. Important Safety Instructions 4
3. Controller Input And Outputs 6
4. Operating Controls 7
5. Set up Requirements 8
5.1 Kit Contents 8
5.2 Choosing your Set up 8
6. Pre-Installation Requirements 9
6.1 Initial Check 9
6.2 Selecting the installation location 9
6.3 Drive Unit Pre-assembly 9
7. Installation 10
7.1 Mounting The Drive Unit 10
7.2 Installing The Logic Or Manual Console 10
8. Programming The Opener 11
9. Safety Beam Installation 12
9.1 Fitting the Safety Beam 12
9.2 Wiring the Safety Beam to V1 Logic Console 12
9.3 Wiring the Safety Beam to V2 Logic Console 13
9.4 Alignment 13
10. Setting Limits via Console 14
10.1 Setting Travel Limits With Manual Console 14
10.2 Clearing Travel Limits With Manual Console 14
10.3 Setting Travel Limits with Logic Console 14
11. Setting Limits via Transmitter 15
11.1 Code A Transmitter For Limit Setting 15
11.2 Storing Transmitter Code 15
11.3 Navigating To “Set Door Travel Menu” 15
11.4 Setting Limits Via Transmitter 15
11.5 To Recalculate Travel Times 15
12. Coding Transmitter 16
12.1 Coding Transmitter Button 16
12.2 Selecting Function Of The Button 16
12.3 Returning To Main Screen 16
13. Remotely Coding Transmitters 16
13.1 Selecting The Function To Be Coded 16
13.2 Activate Remote Code Set Mode 17
14. Setting Pedestrian Position 17
14.1 Setting Pedestrian Position 17
14.2 Checking Pedestrian Position 17
14.3 Error Displays 17
13.3 Removing the Battery From the Transmitter 17
15. Auto-Close Mode for V1 Console 18
15.1 Safety Close Mode 18
15.2 Setting Up Satndard Auto-Close Mode 18
15.3 Safety Beam Triggered Auto Close 18
15.4 Pedestrian Auto-Close 18
15.5 Auto-Close After Obstruction: 18
16. Auto-Close Mode for V2 Console 19
16.1 Safety Close Mode 19
16.2 Setting Up Satndard Auto-Close Mode 19
16.3 Safety Beam Triggered Auto Close 19
16.4 Pedestrian Auto-Close 19
16.5 Auto-Close After Obstruction: 19
17. Time Clock 20
17.1 Time Clock Operation 20
17.2 Time Clock Settings 20
17.3 Day Light Saving Time Adjustment 21
18. Accessories Installation 21
19. Specifications 22
20. Troubleshooting 23
21. Maintenance 24
21.1 Shutter Maintenance 24
21.2 Lubrication (every 3 - 6 months) 24
21.3 Shutter Service and Repair 24
21.4 Opener Maintenance 24
21.5 Service Indicator 24
22. Appendix 25
A - Console Menu Structure 25
B - Viewing & Editing Logic Console Parameters 28
C - Control Board Adjustments 29
D - Diagnostic Tools 31
E - Memory Tools 32
F - Transmitter Editing 33
G - Transmitter Management 35
Warranty and Exclusion of Liability 36

4Axess Pro Series 3000 Owner Installation Instructions
WARNING! • The shutter may operate unexpectedly, therefore do not allow
anything to stay in the path of the door.
• For Safety protection, a Safety Beam must be fitted with logic
console. Failure to comply will void the warranty and may result in
serious personal injury and/or property damage .
• The drive must not be used with a shutter incorporating a wicket door,
unless the drive cannot be operated with the wicket door open.
• The drive is intended to be installed at least 2.5m above the floor.
• DO NOT allow children to operate the opener. Any device that can
operate the opener, make sure it is out of reach of children and that
the doorway is in full view at all times. Serious personal injury and/or
property damage can result from failure to follow this warning.
• When using auto close mode, a Safety (Photo Electric) Beam must
be fitted correctly and tested for operation at regular intervals.
Extreme caution is recommended when using auto close mode.
All safety rules must be followed.
ELECTROCUTION! • Place opener in protected area so that it does not get wet.
• Do not spray with water .
• Disconnect the power cord from mains power before making any
repairs or removing covers. Only experienced service personnel
should remove covers from the opener.
• If the power supply cord is damaged, it must be replaced by an
Automatic Technology service agent or suitably qualified person.
• Electrical wiring must be compliance with the local building an
electrical codes.
The safety alert symbols below indicate a personal
safety or property damage instruction exists.
READ THESE INSTRUCTIONS CAREFULLY.
This automatic shutter opener is designed and tested to
offer safe service provided it is installed and operated in
strict accordance with the following safety rules. Failure
to comply with the following instructions may result in
death, serious personal injury or property damage.
2. Important Safety Instructions

Owner Installation Instructions Axess Pro Series 3000 5
2. Important Safety Instructions
CAUTION:
Emergency access • If your facility has no pedestrian entrance door, an emergency access device
should be installed.
Entrapment under
operating door • DO NOT operate the opener unless the shutter is in full view and free from objects
such as cars and children/people. Make sure that the shutter has finished moving
before entering or leaving the premises.
• Do not allow children to play with shutter controls or transmitters.
• Ensure the shutter is in good working order by undertaking regular servicing.
• For ADDITIONAL SAFETY protection we STRONGLY recommend the fitting of a
Safety (Photo Electric) Beam.
• Safety beams must be installed if the closing force at the bottom edge of the door
exceeds 400N (40kg)
Installation • Frequently examine the installation, in particular, springs and mountings for signs
of wear, damage or imbalance. DO NOT use if repair or adjustment is needed
since a fault in the installation or an incorrectly balanced shutter may cause injury.
DO NOT attempt to repair the shutter yourself as hardware is under extreme
tension.
•The shutter must be well balanced and in good working order. Shutter springs,
brackets and their hardware are under extreme tension and can cause serious
personal injury. Do not attempt to adjust them. A faulty shutter must be repaired
by a industrial roller shutter professional prior to opener installation.
• Remove or disengage all shutter locks and mechanisms prior to installation of the
opener.
• Ensure no parts of the shutter or installation extend over public paths or roads.
• After installation a full function test of the system and safety devices must be
done.
Security • Make sure the shutter is fully closed before leaving the driveway. .
Entanglement in
moving door • Keep hands and loose clothing clear of shutter and opener at all times.

6Axess Pro Series 3000 Owner Installation Instructions
3. Controller Input And Outputs
Motor identification harness connector
Clutch interlock microswitch connector
Serial interface connector
Position sensor connector
10 Amps slow blow mains fuse
03
04
02
01
05
01
02
03
04
05
Fig 3.1
Fig 3.2 - AX3105 & AX3110
03
04
02
01
05
L1 L2 L3 EARTH
07
06
Fig 3.3 - AX3305, AX3310 & AX3315
Motor identification harness connector
Clutch interlock microswitch connector
Serial interface connector
Position sensor connector
FLQ10 - 500Vac time delayed fuse x 3
TDC11- 250mA 1000Vac slow blow fuse
3-phase 415Vac mains input terminal
01
02
03
04
05
06
07

Owner Installation Instructions Axess Pro Series 3000 7
11
10
15
09
08 16
14
13 12
Terminal Block ( From Left To Right )
V1 Console:
V+ Three WireSafety Beams “ + “ Supply
IN3 Three Wire Safety Beams Trigger Input
V- Common For Two Wire Safety Beam and
Three Wire Safety Beams
IN2 Two Wire Safety Beam Input
AUX OUT Receiver’s Auxiliary Output
FIRE Input Terminal (N/O or N/C)
GPI N/O Input Terminal (N/O)
OPN Input Terminal (N/O or N/C)
STP Input Terminal (N/O or N/C)
CLS Input Terminal (N/O)
SWP Input Terminal (N/O)
COM Terminal For Inputs
V2 Console:
AUX OUT Receiver’s Auxiliary Output
V+ Accessory Supply
SB3 Third Safety Beam Input
SB2 Second Safety Beam Input
SB1 First Safety Beam Input
0V Common For Safety Beams
0V Common Terminal For Control Inputs
FIRE N/O , N/C Input Terminal
GPI N/O Input Terminal
OPN N/O , N/C Input Terminal
STP N/O , N/C Input Terminal
CLS N/O Input Terminal
Programmer PG-3 Input
Console Previous Button
Liquid Crystal Display
Console Next Button
Console Open Button
Console Stop Button
Console Set Button
Console Close Button
RJ45 Connector
08 09
10
11
12
13
14
15
16
4. Operating Controls
09
13
14 15
16
17 17
17
Fig 4.1 - Logic Console Fig 4.2 - Manual Console

8Axess Pro Series 3000 Owner Installation Instructions
5. Set up Requirements
Fig 5.1
1
2
3
4
5
6
7
8
9
10
11
12
ITEM DESCRIPTION QTY ORDER
CODE
2 COMMUNICATION CABLE 1 61909
3 TIMING ASSEMBLY 1 61868
4 MOUNTING FLANGE 1 18026
5 OUTPUT DRIVE SHAFT ASSEMBLY 1 64536
6 SPROCKET 14T (0.625”) 1 64703
7 CHAIN 10B (0.625’) 1 63026
AX30 FASTENER PACK (61703)
8 HEX BOLT DW M8 X 20 AND WASHERS 4 10116
9 HEX HEAD SCREW M8 X 38 AND WASHER 4 10105
10 HEX HEAD SCREW ZP (M12 X 35) AND WASHERS 4 10068
11 LOCK NUT KM6 1 10935
12 LOCKING WASHER MB6 1 10985
AUTOMATED FULL LOGIC SET UP
13 LOGIC CONSOLE 1 18050
14 TRICODETM128 KEYRING TRANSMITTERS 2 61160
15 SAFETY BEAMS WITH WIRES AND BRACKETS 1 61903
DEAD MAN SET UP
16 MANUAL CONSOLE 1 18051 13 14
15
16
5.2 Choosing your Set up
The Axess Pro 3000 can be set up in two ways and therefore may require additional
items. Set ups are as follows;
Set Up Items Required
Dead Man Set Up Drive Unit, Manual Console
Automated Full Logic Set Up with
Safety Beams
Drive Unit, Logic Console, transmitter
and safety beams.
5.1 Kit Contents
ITEM DESCRIPTION MODEL
1
AXESS 3100 POWER DRIVE UNIT
(Single Phase Power)
AX3105
AX3110
AXESS 3300 POWER DRIVE UNIT
(Three Phase Power)
AX3305
AX3310
AX3315

Owner Installation Instructions Axess Pro Series 3000 9
6. Pre-Installation Requirements
The Axess®Pro Series 3000 is designed to operate most
industrial heavy duty roller shutters. The shutter must be in good
working condition and travel freely in the guides.
6.1 Initial Check
Before commencing installation, check the following:
a. The shutter moves freely for the full travel in both directions.
b. The mounting must be a solid construction (concrete, brick
or steel) and must be able to withstand the full driving force
applied to the shutter.
c. For full automatic operation a Safety Beam must be fitted to
the logic console. The Safety Beam should be positioned as
close to the shutter as practicable.
SINGLE PHASE (3105 & 3110 models): Require a 240V 10 Amp
power point located within one metre of the drive unit.
6.2 Selecting the installation location
Overall dimensions of the opener are shown in Fig. 6.1 - 6.3.
When selecting the installation location, consider the following:
•Minimum distance between the shutter drum and mounting
plate needs to be more than 15mm and less than 100mm.
•Minimum distance between the drive unit and the imposing
structure is 10mm.
•The overhead clearance needs to be at least 150mm.
6.3 Drive Unit Pre-assembly
The opener can be installed on either the right- or left hand side
of the shutter (when viewed from inside the building). The timing
assembly, mounting flange and drive shaft needs to be assembled
according to the installation side. Assembling the opener for RIGHT-
HAND installation is listed below and shown in Fig 6.4. For LEFT-
HAND side installation, assemble the parts from the other end.
a. Assemble the mounting flange 4 with four M8x38 screws 9
to the drive unit 1.
b. Insert the output drive shaft 5into the gearbox, thread side
first.
c. Secure the output drive shaft with the lock washer 11 and
lock nut 12 .
d. Finger tighten the lock nut* 12 then lock it by securing the
position of the lock nut by bending one tooth of the lock
washer 11 into the slot on the lock nut. (Fig 6.4 insert)
e. Line up the shaft of the timing assembly 3with the keyway
on the back of the drive shaft. Push and secure the timing
assembly with four M8x20 bolts 8 ensuring the cable gland
is facing the motor.
NOTE: The drive unit is not designed to be mounted upside
down. Gearbox damage will result.
* Finger tighten the lock nut, this will remove any movement
in the output shaft. Excessive tightening to lock nut may cause
damage to output shaft bearing.
















   




















 

















 
 
 




 

 

 
 





495mm
85mm
200mm
260mm
IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION
Warning: Incorrect installation can lead to severe injury.
Follow ALL installation instructions.
Fig 6.1
Fig 6.2
Fig 6.3
Fig 6.4
9
5
4
1
8
3
10
11

10 Axess Pro Series 3000 Owner Installation Instructions
NOTE: 5 metres of
communication cable is
supplied with the opener.
WARNING! Do not turn the power on
to the opener before connecting either
console.
Floor
1.5 metre from floor
7.1 Mounting The Drive Unit
Open the shutter about one metre from the floor.
Raise the drive unit to the required height by using a suitable lifter
or use chain block connected to a secure beam above the shutter
axle.
a. Position opener and secure with four M12x35 screws 10 .
b. Mount drive sprocket 6 on shaft 5in line with shutter drive
gear. Tighten the grub screw on the sprocket 6 with M4 hex
key.
c. Shorten drive chain 7 as required and fit around drive gears.
d. Feed manual chain (not supplied) through guide and over the
clutch pulley.
e. Shorten the manual chain as required and fix ends to make a
loop.
NOTE: Ensure that hand chain is not twisted when making a loop.
WARNING! Do not turn the power on to the opener
before connecting either console.
7.2 Installing The Logic Or Manual Console
1. Remove the main cover.
2. Affix the logic or manual console at a height of 1.5 metres
within sight of the shutter. Make sure that the position of
the logic or manual console is out of reach of children and
convenient to the customer (Fig. 7.1).
3. Connect the communication cable 2from the opener to the
logic or manual console unit.
WARNING! For full automatic operation a Photo Electric
Beam Sensor (Safety Beam) must be fitted with logic
console. Failure to comply will void the warranty and may
cause serious personal injury and/or property damage.
WARNING! Ensure that network cable is affixed properly
and away from the moving parts of the shutter and
opener.
7. Installation
Fig 7.1

Owner Installation Instructions Axess Pro Series 3000 11
Fig 7.1
The most common programs are;
Program Menu’s required Function Section
Dead Man Set Up Manual Console Setting the Limits 10.1
Automated Full Logic Set
Up with Safety Beams
Menu 10.1 Setting the Limits 11.1 or 12.4
Menu 1 Coding the Transmitter 13.1
Menu 6.1 Safety Close Mode 16.1
Menu 3 Auto Close Times 16.2 to 16.5
For the Dead Man Set Up the shutter can not be closed by Auto-Close or by
transmitters. When Safety Beams are not installed, the controller will display the
following message;
ATTENTION! No Safety Beams have been detected. “Safety
Close’ mode has been turned on. See Manual for details.
Press SET to continue.
NOTE: Fitting Safety Beams enables the Auto-Close feature to become active.
8. Programming The Opener

12 Axess Pro Series 3000 Owner Installation Instructions
9. Safety Beam Installation
Safety Beams
Safety Beams extend across the doorway opening. The Safety Beam is
designed to detect an obstruction while the shutter is closing and to send
a signal to the opener to reverse or stop the shutter movement.
9.1 Fitting the Safety Beam
a. Attach the mounting bracket 4to the adjustment bracket 3with the
pan head screw 6. (Fig. 6.1)
b. Attach the bracket 2to the Safety Beam transmitter with four taptite
screws (m3x5) 7and attach the other side to the adjustment bracket
3with the pan head screw 6.
c. Repeat steps a and b to assemble the Safety Beam receiver.
CAUTION: Locate the Safety Beam in a strategic location in the
doorway. Automatic Technology recommend that the sensor is
placed 100mm above the floor level and as close as possible to
the door opening.
9.2 Wiring the Safety Beam to V1 Logic Console
a. Connect the wires from the Safety Beams wiring harness to terminal
block.
i. By default the Axess®Pro Series 3000 will take two wire safety
beams (connect one wire to IN2 input and the second wire to V-,
next to the IN2 terminal (Fig. 6.2) ).
ii. The V1 Console will only take 2 wire safety beams or 3 wire beams
not a combination of both.
b. For three wire beams connect the Resistor 5k6 ohms (Green Blue
Red Gold) 5to number 2 (two) and 4 (four) terminal on the Safety-2
receiver (Fig. 6.3). Make sure to align the beams correctly. Follow the
manual supplied with the Safety Beams.
c. Ensure you program the Axess®Pro Series 3000 to idenitfy what type
of Safety Beam or combination of Safety Beams you have installed.
i. Press NEXT to Navigate to Menu 6
ii. Press SET to display Menu 6.4 (for IN3).
iii. Use the UP and DOWN arrows to change the Safety Beam type
from two to three wires.
iv. Press SET to accept the selection.
V+
IN3
V−
RED
BLUE
GREEN
GOLD
BLACK BLACK BLACK BLACK
YELLOW
RED
YELLOW
RED
++-
-
RED
P.E BEAM
Fig 9.1
Fig 6.3
12
3
4
7
6
6
5
IN2
V -
RED
BLACK
RED
BLACK
RED
BLACK
BLACK
Fig 6.2
WARNING: When using Safety Beams, the doorway must be
clear of all obstructions and persons at all times. The location
of the beams and manner in which it is installed might not
give safety protection at all times. Check to make sure
that the height of the beam and type used give maximum
protection possible
WARNING: Tampering with Safety Beams could result in
serious personal injury and/or property damage and will void
the warranty.
V+
IN3
V−
RED
BLUE
GREEN
GOLD
BLACK BLACK BLACK BLACK
YELLOW
RED
YELLOW
RED
++-
-
RED
P.E BEAM
IN2
V -
RED
BLACK
RED
BLACK
RED
BLACK
BLACK

Owner Installation Instructions Axess Pro Series 3000 13
9. Safety Beam Installation
Fig 6.3
WARNING: When using Safety Beams, the doorway must be
clear of all obstructions and persons at all times. The location
of the beams and manner in which it is installed might not
give safety protection at all times. Check to make sure
that the height of the beam and type used give maximum
protection possible
WARNING: Tampering with Safety Beams could result in
serious personal injury and/or property damage and will void
the warranty.
V+
IN3
V−
RED
BLUE
GREEN
GOLD
BLACK BLACK BLACK BLACK
YELLOW
RED
YELLOW
RED
++-
-
RED
P.E BEAM
9.3 Wiring the Safety Beam to V2 Logic Console
a. Connect the wires from the Safety Beams wiring harness to
terminal block.
i. By default the Axess®Pro Series 3000 will only take two wire
safety beams (connect one wire to SB3, SB2 or SB1 input and
the second wire to 0V, next to the SB1 terminal (Fig. 9.4) ).
ii. The V2 Console can take up to three (3) two wire safety beams
but is NOT compatible with three wire safety beams.
b. Make sure to align the beams correctly. Follow the manual supplied
with the Safety Beams.
WARNING: When using Safety Beams, the doorway must be
clear of all obstructions and persons at all times. The location
of the beams and manner in which it is installed might not
give safety protection at all times. Check to make sure
that the height of the beam and type used give maximum
protection possible
WARNING: Tampering with Safety Beams could result in
serious personal injury and/or property damage and will void
the warranty.
9.4 Alignment
a. Power up the Axess®Pro Series 3000 with the Safety Beam
connected. The green LED on the transmitter should turn ON to
indicate power is present.
b. If the receiver is connected to power and the red LED is flashing
while the green LED on the transmitter is on, the transmitter and
receiver are not aligned.
c. Make horizontal and/or vertical adjustment on the transmitter and/
or receiver until the red LED on the receiver turns on, indicating
alignment. Approaching to the alignment is indicated by fast
flashes on the red receiver LED.
SB1
OV
RED
BLACK
RED
BLACK
RED
BLACK
BLACK
Fig 9.4
SB1
OV
RED
BLACK
RED
BLACK
RED
BLACK
BLACK

14 Axess Pro Series 3000 Owner Installation Instructions
To Desired
CLOSE Limit,
SET
To Desired
OPEN Limit, SET
10. Setting Limits via Console
10.3 Setting Travel Limits with Logic Console
a. Turn on the power to the opener. The controller will go through a start up
sequence.
b. After a short delay the MAIN SCREEN (Fig. 11.1) will be displayed. If this is
the first time the Axess®Pro Series 3000 is being used, the MAIN SCREEN
should enter into limit set mode and the blue close LED will be flashing. If
the display shows that an input is active, then rectify the situation before
continuing with the procedure for setting the travel limits. Press and hold
the CLOSE button - the shutter should start closing.
i. If the shutter opens, release the CLOSE button and press the STOP
button once to change the motor’s direction. Press and hold the
CLOSE button until close position of the shutter is reached.
ii. If the shutter overshoots, press the OPEN button to move the shutter in
the open direction.
c. When the shutter is at the desired close position, press the SET button to
record the close limit position. The display will change and the green open
LED will start to flash (Fig. 11.2).
d. Press and hold the OPEN button to open the shutter. When the shutter is
at the desired open position, release the OPEN button
i. If the shutter overshoots, press the CLOSE button to move the shutter
in the CLOSE direction.
WARNING! Once the next step is performed, the shutter will
automatically close and open to calculate travel time settings.
Keep persons and objects clear of the shutter.
e. Press the SET button to store the open limit. The shutter will now automatically
close and open to calculate the travel time settings. After this, If PE Beams are
installed, the opener can be operated with the OPEN or CLOSE button on the
logic console or from the transmitter. Otherwise, the controller will be loaded
with “Safety Close Mode”. (Section 16.1)
Fig 10.3
Fig 10.4
PRESS
PRESS
10.1 Setting Travel Limits With Manual Console
a. Turn on the power to the opener. After a short delay blue close LED will
start to flash.
b. Press and hold the CLOSE button (Fig. 10.1) - the shutter should start closing.
i. If the shutter opens, release the CLOSE button and press the STOP
button once to change the motor’s direction. Press and hold the
CLOSE button until close position of the shutter is reached.
ii. If the shutter overshoots, press the OPEN button to move the shutter in
the open direction.
c. When the shutter is at the desired close position, press the SET button to
record the close limit position. The green open LED will start to flash.
d. Press and hold the OPEN button (Fig. 10.2) to open the shutter. When the
shutter is at the desired open position, release the OPEN button
i. If the shutter overshoots, press the CLOSE button to move the shutter
in the CLOSE direction.
WARNING! Once the next step is performed, the shutter will
automatically close and open to calculate travel time settings.
Keep persons and objects clear of the shutter.
e. Press the SET button to store the open limit. The shutter will now automatically
close and open to calculate the travel time settings.
f. Replace the main cover. The opener can now be operated with the OPEN or
CLOSE buttons on the manual console.
10.2 Clearing Travel Limits With Manual Console
a. Turn power to the opener off.
b. Press and hold the SET Button.
c. Turn power on while holding the SET button. Continue to hold until all
LED’s are off.
d. Repeat 10.1 to set travel limit positions.
Fig 10.1
Fig 10.2
The manual console has open, close, stop and set push buttons. The status of the door is indicated by the LED lights. The manual console only
supports Safety Close mode. In this mode, the user must press and hold the close button to close the door. The door can be opened by pressing
the open button once.
NOTE: Safety (Photo Electric) Beams, transmitters
or any other device to control the operation of the
shutter is not supported by the manual console.

Owner Installation Instructions Axess Pro Series 3000 15
Fig 10.3
Fig 10.4
In order to use a transmitter to set the limits, it must first have at least
one of its buttons coded to the logic console. The function assigned
to the transmitter’s buttons is of no concern here as the buttons are
temporally assigned to OPEN, CLOSE and SET (Fig. 11.2).
11.1 Code A Transmitter For Limit Setting
a. Press NEXT to navigate to Menu 1.
b. Press SET to enter the code set procedure (Fig. 11.1).
11.2 Storing Transmitter Code
a. The logic console will prompt to press one of the transmitter’s
button.
b. Press the transmitter button you wish to use to operate the opener
(e.g. button 1) .
c. Press the same transmitter button again as prompted by the display.
d. Press the SET button to store the transmitter.
11.3 Navigating To “Set Door Travel Menu”
a. Press PREV to navigate to Menu 10.
b. Press SET to display MENU 10.1.
c. Press SET two times to enter the limit setting procedure. The close
blue LED will start to flash.
11.4 Setting Limits Via Transmitter
a. Press and hold Button 4 on the transmitter to close the shutter.
i. If the shutter opens, release button 4 and press the STOP
button once on the logic console to change the direction of
the motor. Then press and hold Button 4 on the transmitter to
close the shutter.
ii. If the shutter is closed too far, press Button 1 to “inch” the
shutter towards open.
b. When happy with the close limit position, press Button 2 to store
this in the memory. The open green LED will starts to flash. Press
Button 1 to open the shutter.
i. If the shutter is opened too far, press Button 4 to “inch” the
shutter closed.
WARNING: The shutter will automatically close and open
once the next step is performed. Ensure that no persons or
objects are in the path of the shutter.
c. When you are happy with the open limit position, press Button 2 on
the transmitter to store into memory. Theshutterwill now automatically
close and open to calculate the travel times and other settings.
d. After this, if PE Beams are installed, then the opener can be
operated with the OPEN or CLOSE button on the logic console or
from the transmitter. Otherwise, the controller will be loaded with
“Safety Close Mode”. (Section 16.1)
11.5 To Recalculate Travel Times
Reprofiling is a simplified way of re-learning the travel characteristic
of a previously setup Limit Switch travel installation. Re-profiling can
be used when the travel characteristics of the shutter change due to
mechanical adjustments etc.
1. To initiate a re-profile, locate “MENU 10.2 Reprofile Travel”
2. Press SET and follow the prompts.
The shutter will start to move and re-calculate force margins. The
shutter can move between the open and close limit positions up
to two (2) times (depending on the position of the shutter and the
power up condition). A single beep will be heard once the process is
complete.
11. Setting Limits via Transmitter
Button 1
(Inch Open)
Button 4
(Inch Close)
Button 2
(Set)
MENU 1
Code Transmitter
PR E S S
Coding Button
Fig 11.1
Fig 11.2
IMPORTANT NOTE:
Only TrioCodeTM128 Technology Transmitters
are compatible with the Axess® Pro Series 3000
products.
Fig 10.1
Fig 10.2

16 Axess Pro Series 3000 Owner Installation Instructions
12. Coding Transmitter
The Axess®Pro Series 3000 can store 511 transmitters in its memory.
Each transmitter can be allocated an alpha-numeric ID label up
to eleven characters in length and each button can be assigned to
one of several control functions. The settings for a transmitter are
represented in Fig. 12.1. It shows the transmitter’s store number, ID
label or serial number and the functions assigned to each of the four
buttons. To toggle between ID/SN display, press UP/DOWN with the
cursor on the ID/SN indicator. The procedures below code, delete,
replace, edit and copy transmitter records.
12.1 Coding Transmitter Button
Navigating To Menu 1 “Code Transmitter”
a. Press NEXT to navigate to Menu 1 (Fig. 12.2).
b. Press SET to enter the code set procedure.
Storing Transmitter Code
a. The logic console will prompt to press one of the transmitter’s
buttons.
b. Press the transmitter button you wish to use to operate the opener
(e.g. button 1) (Fig. 12.3) .
c. Press the same transmitter button again as prompted by the
display.
12.2 Selecting Function Of The Button
The logic console will now show the transmitter’s record, with
a cursor on the field for the button being coded (Fig. 12.4). Use
OPEN/CLOSE to select the function for the button.
Available functions:
OSC (Open/Stop/Close) PED (Pedestrian access)
SWP (Swipe) CLS (Close)
OPN (Open) STP (Stop)
LGT (Courtesy Light) VAC (Vacation Mode)
AUX (Auxiliary ) OFF (No action)
NOTE: OSC can change to OS and CLS (Close) function, but is not
available in the case where PE Beams are not installed.
Press SET to save the settings or STOP to abort without saving.
12.3 Returning To Main Screen
Press STOP to return to the MAIN SCREEN and test the transmitter.
NOTE: To edit the other settings, refer to transmitter edit procedure
in Appendix F.
If a transmitter is already coded into the opener, additional
transmitters can be coded without being in direct contact with the
opener’s wall console unit.
NOTE: Only the function of the existing transmitter button can
be assigned to new transmitter. Please read instructions prior to
proceeding - there is a time-out facility for security reasons.
13.1 Selecting The Function To Be Coded
a. Using the existing transmitter, operate the shutter with the
transmitter button which has the function to be coded (Fig. 13.1)
(e.g. Button 1 has been coded with the OSC function assigned).
b. If the button’s function activates the shutter (PED, SWP, OSC, CLS,
STP or OPN) wait for the shutter to complete its cycle.
123ID Name/SN
OSC PED LGT VAC
MENU 1
Code Transmitter
PR E S S
# 1 [No Name]
OSC OFF OFF OFF
PRESS
PRESS
Press Tx’er
Button! List
PR E S S
I.D label/Serial number
Button 4 function
Button 3 functionButton 2 function
Button 1 function
Store number
ID/SN display indicator
Fig 12.1
Fig 12.2
Fig 12.3
Fig 12.4
PRESS
Existing
transmitter
Fig 13.1
IMPORTANT NOTE:
Only TrioCodeTM128 Technology Transmitters are compatible
with the Axess® Pro Series 3000 products.
13. Remotely Coding Transmitters

Owner Installation Instructions Axess Pro Series 3000 17
13.2 Activate Remote Code Set Mode
c. Use a small pin to press and hold through the Coding Hole of the existing
transmitter for 2 seconds (Fig. 13.2).
d. Within 10 seconds, press the button on the new transmitter you wish to
code for 2 seconds (Fig. 13.3).
e. Press the same button again (within 10 seconds)
for confirmation.
f. Test Operation. The new transmitter button should now function as the
existing transmitter.
PRESS
New
transmitter
Existing
transmitter
Fig 13.2
Fig 13.3
NOTE: When a transmitter is remotely coded, its ID label is set to that
of the existing transmitter. If the existing transmitter does not have an ID
label assigned, then the ID label of the new transmitter is set to: R/C Tx
###, where ### is the existing transmitters store number. This ensures that
the originator of any remotely coded transmitter can be identified.
NOTE: To Manage your Transmitters, refer to Transmitter Management
in Appendix G.
13.3 Removing the Battery From the Transmitter
(Battery Type: 3V Lithium Battery CR2032).
Use a non-metallic object (e.g. pen) to remove the battery. (Fig. 13.4).
To test the battery is working, press and hold a transmitter button;
(Fig. 13.5).
Light Status Battery Status
Solid OK
Flashing Requires replacement
No light Requires replacement
REPLACE BATTERY WITH CR2032 ONLY
Fig 13.4
Fig 13.5
Use a pen
to push the
battery down
through the
side opening
to release
battery
14. Setting Pedestrian Position
After completing the limit setup procedure the Pedestrian Access
position is automatically set to a position which is approximately in
the middle of the door travel. The position can be manually set by
following the Setting Pedestrian Position procedure.
14.1 Setting Pedestrian Position
a. Drive and stop the door at the desired Pedestrian Access
position by using a transmitter or wall control unit.
b. Press PREV to navigate to Menu 10.
c. Press SET. MENU 10.1 will be displayed.
d. Press NEXT to go to MENU 10.3
e. Press SET on the wall control unit to save the Pedestrian Access
position (Fig. 14.1).
f. Press the STOP button to exit to the main screen.
14.2 Checking Pedestrian Position
When activated by a transmitter button which is coded as Ped
mode, the opener drives the door to the preset position from
either above or below. Ped Mode’s active status is indicated on the
display (Fig. 14.2).If a Ped Mode button is pressed while the door
is moving, the door will stop. If a Ped Mode button is pressed when
the door is in the Ped position, then the door will close.
14.3 Error Displays
During the above procedure many error checks are performed. If
an error is detected, a message will be displayed indicating the
error.
MENU 10.3
Set Pedestrian
PR E S S
Ped’n Access
FRI 11:06:44 STD
Fig 14.1
Fig 14.2

18 Axess Pro Series 3000 Owner Installation Instructions
15.1 Safety Close Mode
The controller has a built in Safety Beam detection. If Safety
Beams are not installed, the controller will automatically turn on
the Safety Close Mode. By enabling this parameter, the shutter
can only be closed by holding the close button on the wall control
unit (Dead Man Set Up).
In order to facilitate an Automated Set Up and enable to shutter
to be closed by a transmitter proceed by;
Navigate to “Safety Close Mode (Menu 6.1)”
a. Press the OPEN button.
b. Warning will display.
DANGER! Read Manual before turning off Safety
Close Mode. Press SET to continue.
c. Press SET to accept the warning.
d. Press either the OPEN or CLOSE arrows to change to OFF.
e. Press SET to Save the change.
WARNING! The Auto-Close function is not
available unless Safety Beam is installed.
15.2 Setting Up Satndard Auto-Close Mode
Menu 3. Auto-Close Times
The Auto-Close modes automatically close the shutter after it has
been operated. To implement this the controller starts a timer
once the shutter has reached its desired open position. The
timer then counts down and when it expires the controller starts
to close the shutter. Details about the four Auto-Close modes
follow. Automatic Technology strongly recommend using a Safety
Beam for added safety.
Menu 3.1 Standard Auto Close
This mode is selected by entering a non-zero time for the STD
Auto-Close parameter. When selected, the shutter will Auto-Close
after being fully opened (except when the shutter has reversed
to the open position after a motor obstruction or overload.
Countdown is suspended by: S.B., OPN or SWP input being
active. The countdown is aborted if the STP input is activated.
If the shutter is already open and the OPN or the SWP input is
activated, then the countdown will start.
15.3 Safety Beam Triggered Auto Close
Menu 3.2 Directional Auto-Close (SB Auto Close)
This mode is selected by entering a non-zero time for the “Safety
Beam Auto-Close” parameter. Second Safety beam must be
installed and connected to OPN input. Sub menu 5 : OPN I/P
2nd P.E in menu 7 Operating modes must be selected “ON” and
also sub menu 4: OPN I/P N/C operation in menu 7 Operating
modes must be selected “ON”.
This mode is used to auto-close the door only after a vehicle
have passed through the doorway to exit the premises . The 2nd
Safety Beam (OPN) input must be active when the Safety Beam
input is activated in order for Safety Beam triggered auto-close
to be activated .
This mode is usefull for fire brigade ,ambulance stations etc.
15. Auto-Close Mode for V1 Console
15.4 Pedestrian Auto-Close
Menu 3.3 Pedestrian Auto-Close
This mode is selected by entering a non-zero time for the “Ped’n
A/C” parameter. When selected, the door will Auto-Close after being
opened for pedestrian access unless it was following a reverse from
an obstruction.
Menu 3.4 (Safety Beam) Pedestrian Auto-Close
This mode is selected by entering a non-zero time for the “Ped’n
A/C” parameter. When selected, the door will Auto-Close after being
opened for pedestrian access unless it was following a reverse from
an obstruction.
15.5 Auto-Close After Obstruction:
Three parameters are provided to enable the Auto-Close feature to
be activated after obstructions and power up. Normally the Auto-
Close feature is not enabled after obstructions for safety reasons.
Safety Beams must be used for these features to be activated. The
three parameters are:
Menu 3.5 (Auto-Close after close overload)
This mode enables the Auto-Close feature to be activated when a
close overload occurs (requires Safety Beams).
Menu 3.6 (Auto-Close after open overload)
This mode enables the Auto-Close feature to be activated when an
open overload occurs.
Menu 3.7 (Auto-Close after power up)
This mode enables Auto-Close feature after power up.

Owner Installation Instructions Axess Pro Series 3000 19
16.1 Safety Close Mode
The controller has a built in Safety Beam detection. If Safety
Beams are not installed, the controller will automatically turn on
the Safety Close Mode. By enabling this parameter, the shutter
can only be closed by holding the close button on the wall control
unit (Dead Man Set Up).
In order to facilitate an Automated Set Up and enable to shutter
to be closed by a transmitter proceed by;
Navigate to “Safety Close Mode (Menu 6.1)”
a. Press the OPEN button.
b. Warning will display.
DANGER! Read Manual before turning off Safety
Close Mode. Press SET to continue.
c. Press SET to accept the warning.
d. Press either the OPEN or CLOSE arrows to change to OFF.
e. Press SET to Save the change.
WARNING! The Auto-Close function is not
available unless Safety Beam is installed.
16.2 Setting Up Satndard Auto-Close Mode
Menu 3. Auto-Close Times
The Auto-Close modes automatically close the shutter after it has
been operated. To implement this the controller starts a timer
once the shutter has reached its desired open position. The
timer then counts down and when it expires the controller starts
to close the shutter. Details about the four Auto-Close modes
follow. Automatic Technology strongly recommend using a Safety
Beam for added safety.
Menu 3.1 Standard Auto Close
This mode is selected by entering a non-zero time for the STD
Auto-Close parameter. When selected, the shutter will Auto-Close
after being fully opened (except when the shutter has reversed
to the open position after a motor obstruction or overload.
Countdown is suspended by: S.B., OPN or SWP input being
active. The countdown is aborted if the STP input is activated.
If the shutter is already open and the OPN or the SWP input is
activated, then the countdown will start.
16.3 Safety Beam Triggered Auto Close
Menu 3.2 (SB AC Trig)
This mode is selected by entering a non-zero time for the “Safety
Beam Auto-Close” parameter. This mode is used to Auto-Close
the shutter but only after an object has passed through the
doorway and has triggered the Safety Beam input. Any Safety
Beam or combination of Safety Beams can be configured to
activate Safety Beam Auto-Close mode and combinations are:
One Beam only
i. Safety Beam 1
ii. Safety Beam 2
iii. Safety Beam 3
Either Beam
iv. Safety Beam 1 or Safety Beam 2
v. Safety Beam 1 or Safety Beam 3
vi. Safety Beam 2 or Safety Beam 3
vii. Safety Beam 1 or Safety Beam 2 or Safety Beam 3
Combination
viii. Safety Beam 1 and Safety Beam 2
ix. Safety Beam 1 and Safety Beam 3
x. Safety Beam 2 and Safety Beam 3
xi. Safety Beam 1, Safety Beam 2 and Safety Beam 3
16. Auto-Close Mode for V2 Console
NOTE: The swipe input can be used to clear the Safety Beam
triggered status so that the Safety Beam input must be activated
again before the countdown will start. As with the other Safety Beam
modes, the STP input will abort countdown and the OPN and SWP
inputs will restart the countdown if the shutter is OPEN.
Menu 3.3 Directional Auto-Close (SB Auto Close)
This mode is selected by entering a non-zero time for the “S.B. Auto-
Close” parameter. S.B 3 Beam must be installed and configured to
EXIT WITH SB1. Sub in menu 6.5. This mode is used to Auto-Close
the shutter only after a vehicle has passed through the Safety Beam
3 and then through Safety Beam 1 to exit the premises . This mode is
useful for fire brigade, ambulance stations etc.
16.4 Pedestrian Auto-Close
Menu 3.4 Pedestrian Auto-Close
This mode is selected by entering a non-zero time for the “Ped’n
A/C” parameter. When selected, the door will Auto-Close after being
opened for pedestrian access unless it was following a reverse from
an obstruction.
Menu 3.5 (Safety Beam) Pedestrian Triggered Auto-Close
Any Safety Beam or combination of Safety Beams can be configured
to activate Safety Beam Auto-Close mode.
Menu 3.6 (Safety Beam) Pedestrian Auto-Close
This mode is selected by entering a non-zero time for the “Ped’n
A/C” parameter. When selected, the door will Auto-Close after being
opened for pedestrian access unless it was following a reverse from
an obstruction.
16.5 Auto-Close After Obstruction:
Three parameters are provided to enable the Auto-Close feature to
be activated after obstructions and power up. Normally the Auto-
Close feature is not enabled after obstructions for safety reasons.
Safety Beams must be used for these features to be activated. The
three parameters are:
Menu 3.7 (Auto-Close after close overload)
This mode enables the Auto-Close feature to be activated when a
close overload occurs (requires Safety Beams).
Menu 3.8 (Auto-Close after open overload)
This mode enables the Auto-Close feature to be activated when an
open overload occurs.
Menu 3.9 (Auto-Close after power up)
This mode enables Auto-Close feature after power up.

20 Axess Pro Series 3000 Owner Installation Instructions
17. Time Clock
NOTE: The most recent program that applies to an output remains
active until a new program takes effect.
NOTE: If a Time Clock program does not have a day selected then
it can not be executed. If a Time Clock program is taking control
of the opener, then this status is displayed on the LCD. The MAIN
SCREEN and clock status screen flashes alternatively.
The opener provides a programmable time clock which can be
used to control the Axess®Pro Series 3000 on a timed basis at
various times of the week. This section details the time clock
operation and configuration.
17.1 Time Clock Operation
The time clock consists of a 7 day clock and storage for 32
programs. The clock is powered by its own battery and therefore
does not lose time when the Axess®Pro Series 3000 is turned off.
Each time clock program defines the time of the day and the days
of the week it is to run and the output function to be executed. Any
combination of the days of the week can be selected.
17.2 Time Clock Settings
The Time Clock settings are accessed by selecting the Time Clock
menu (MENU 7). Press SET (Fig. 17.1) to enter the menu and then
PREV or NEXT to navigate through the options.
Menu 7.1 Set Time/date
This is where the current time, date and day are displayed and set
(Fig. 17.2).
NOTE: The time is in a 24 hour format and the Day of the week is
not automatically set with the date. To change the settings simply
press UP or DOWN to display the cursor and then move to the
field to be changed using the NEXT / PREV buttons. Then press
OPEN/CLOSE to change the setting and then the SET or STOP
buttons to save.
Menu 7.2 View Programs
Select this menu to display or edit the Time Clock programs
(Fig. 17.3). When selected, program number 1 is displayed and
the cursor is shown on the program number field. The other fields
shown include the function, time and days of operation. The
example
Fig. 17.4 shows that the DOOR will OPEN at 7 am on Mondays,
Tuesdays, Wednesdays, Thursdays and Fridays. Use the OPEN /
CLOSE buttons to scroll though the other programs (Fig 17.5).
To edit a program, simply press the NEXT / PREV buttons to move
the cursor onto the required field and press the OPEN/CLOSE
button to change the value. To save the program settings, press
SET or to exit without saving press STOP.
MENU 7.1
Set Time/Date
PRESS
00:00:80 STD
--- 00/00/2000
MENU 7.2
View Programs
PRESS
P#01 OPEN DOOR
07:00:00 MTWTF--
Fig 17.1
Fig 17.2
Fig 17.3
Fig 17.4
The selectable functions available are:
Function Operation
RX = Off From the time when the program with RX = OFF is activated, all the transmitters will be disabled.
RX = On From the time when program with RX = ON is activated, all the transmitters will be enabled.
Open Door From the time when the program with OPEN DOOR is activated, the door will open and stay open.
Stop Door This feature will let the user activate the stop function until the next program starts. The door will not
open or close while stop is activated.
Free Door Release the controls from the timer.
Off This will temporarily disable the program.
.
Fig 17.5