Automatic Technology NeoSlider NES-24V2 User manual

NES-24V2 NeoSliderTM
Sliding Gate Opener
Ne Slider™
Doc # 160023_03
Part # 13333
Released 27/10/14

2NeoSliderTM - Sliding Gate Opener NES-24V2 Owner Installation Instructions
WARNING! • The gate may operate unexpectedly, therefore do not allow anything to stay in the
path of the gate.
• Do not disengage the gate opener to manual operation with children/persons or
any objects including motor vehicles within the gateway.
• Remove or disengage all gate locks and mechanisms prior to installation of the
opener.
• Make sure the gate is fully open before driving into or out of the driveway.
• When using auto close mode, a Photo Electric beam must be fitted correctly and
tested for operation at regular intervals. Extreme caution is recommended when
using auto close mode. All safety rules must be followed.
ELECTROCUTION! • Do not immerse in or spray the NeoSlider with water .
• Disconnect the power cord from mains power before making any repairs or
removing covers. Only experienced service personnel should remove covers from
the gate opener.
• If the power supply cord is damaged, it must be replaced by an Automatic
Technology service agent or suitably qualified person.
• Connect the gate opener to a properly earthed general purpose 240V mains
power outlet installed by a qualified electrical contractor.
CAUTION:
Entrapment from
operating gate • DO NOT operate the gate opener unless the gate is in full view and free from
objects such as cars and children/people. Make sure that the gate has finished
moving before entering or leaving the driveway.
• Do not allow children to play with gate controls or transmitters.
• In order for the NeoSliderTM to sense an object obstructing the gateway, some force
must be exerted on the object. As a result the object, gate and/or person may suffer
damage or injury.
• Regularly check to make sure that the Safety Obstruction Force is working
correctly, and is tested and set as per Section 12 of this manual. Failure to follow
these instructions could result in serious personal injury and/or property damage.
This test must be repeated at regular intervals and the necessary adjustments
made as required.
• If using a key switch, keypad or any device that can operate the gate opener, make
sure it is in a location where the gateway is visible, but out of the reach of children
at a height of at least 1.5m.
• For ADDITIONAL SAFETY protection we STRONGLY recommend the fitting of a
Photo Electric (Safety) Beam. In most countries Safety Beams are mandatory on all
gates fitted with automatic openers.
Installation • Ensure the gate(s) is in good working order . Faulty gates must be repaired by a
qualified technician prior to NeoSliderTM installation.
Security • Make sure that the gate is fully closed before leaving the driveway.
Entanglement in
or laceration from
moving gate
• Keep hands and loose clothing clear of gate at all times
• Keep clear of gate during operation as severe lacerations can occur on sharp edges
of gate.
Important Safety Instructions
The safety alert symbols below indicate a personal safety or property
damage instruction exists. READ THESE INSTRUCTIONS CAREFULLY.
This NeoSliderTM NES-24V2 Sliding Gate Opener is designed and tested to offer safe
service provided it is installed and operated in strict accordance with the following
safety rules. Failure to comply with the following instructions may result in death,
serious personal injury or property damage.

Owner Installation Instructions NeoSliderTM - Sliding Gate Opener NES-24V2 3
Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, statutory
or otherwise which may be implied by laws as conditions or warranties of purchase of an Automatic Technology Australia Pty Ltd Garage Door Opener.
Automatic Technology Australia Pty Ltd hereby further expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever
suffered by any person as a result whether directly or indirectly from failure to install the Automatic Technology Australia Pty Ltd Garage Door Opener in
accordance with these installation instructions.
NeoSliderTM
Sliding Gate Opener NES-24V2
Contents
1. Features 4
2. Control Board Layout 6
3. Set Up Requirements 7
3.1 Kit Contents 7
3.2 Choosing your Set up 7
4. Drive Unit Installation 8
4.1 Initial Checking 8
4.2 Mounting the Drive Unit 8
4.3 Installing antenna 8
5. Rack & Limit Actuator Installation 9
5.1 Mounting rack to gate 9
5.2 Fixing limit actuator to rack 9
6. Programming The NeoSliderTM 10
6.1 Common Programs 10
6.2 Powering up the NeoSliderTM 10
7. Safety Beams 11
7.1 Installation of Safety Beams to the NeoSliderTM 11
7.2 Safety Beam Failure Emergency Close (SBFEC) 11
8. Setting Limits 12
8.1 Setting Travel Limits 12
8.2 Setting the left/right installation side settings 12
8.3 Setting close travel limit 12
8.4 Setting open travel limit 12
8.5 Automatic limit adjustment and load profile 12
8.6 Pedestrian access position 12
8.7 Errors during setting of travel limit 12
9. Safety Obstruction Force Test 13
9.1 Testing Close Cycle 13
9.2 Testing Open Cycle 13
9.3 Force Pressure For Close and Open Cycle. 13
9.4 Reprofiling Travel 13
10. Coding Transmitter 14
10.1 Coding Transmitter Button 14
10.2 Selecting Function Of The Button 14
10.3 Returning To Main Screen 14
11. Remotely Coding Transmitters 15
11.1 Selecting The Function To Be Coded 15
11.2 Activate Remote Code Set Mode 15
11.3 Removing the Battery From the Transmitter 15
12. Setting Pedestrian Position 16
12.1 Setting pedestrian position 16
12.2 Pedestrian Position Set 16
12.3 Error Displays 16
13. Auto-Close Mode 17
13.1 Setting Up Standard Auto-Close 17
13.2 Safety Beam Triggered Auto Close 17
13.3 Pedestrian Auto-Close 17
13.4 Auto-Close After Obstruction 17
14. Accessories Installation 18
14.1 Fitting Solenoid Or Magnetic Locks 18
14.2 Fitting Courtesy Lights 18
15. Specifications 19
16. Troubleshooting 20
17. Appendix 21
A - Console Menu Structure 21
B - Viewing and Editing Parameters 23
C - Wiring Dual NeoSlider Kit 24
D - Control Board Adjustments 25
E - Diagnostic Tools 27
F - Memory Tools 28
G - Transmitter Editing 29
H - Transmitter Managment 30
18. Warranty and Exclusion of Liability 31

4NeoSliderTM - Sliding Gate Opener NES-24V2 Owner Installation Instructions
Operation
To activate the gate simply press a button on the TrioCodeTM128 transmitter,
keypad or other optional control devices. During an open or close cycle, the gate
can be stopped by pressing the button whilst it is in motion. The next actuation
will move the gate in the opposite direction.
Operator Console
The NeoSlider™ features a LCD display operator console which simplifies
installation, adjustments and status indication. Features include editing transmitter
storage and names, setting parameters, selecting specialised operating modes
and performing system diagnostics.
TrioCode™128 Technology
Only transmitters with the TrioCode™128 Technology can operate with the latest
Openers, reducing the chance of intereference from other radio frequency sources.
Every time a TrioCode™128 transmitter is used a new security code is randomly
generated from over 100 billion possibilities. This greatly enhances the security of the
system and makes “code grabbing” a thing of the past. TrioCode™128 transmitters have
the ability to code into earlier model openers.
Security Code Store
The NeoSlider™ Sliding Gate Opener uses revolutionary technology to securely store up to thirty
(30) transmitters in its memory with the ability to assign an 11 character name to each.
Installation
The display console on the NeoSlider™ “holds your hand” through the installation and setup process. Also,
during installation a handheld transmitter can be used to set gate travel limits, allowing the installer to closely
monitor the gate’s position and stop points instead of having to be within arms reach of the console.
Iss (Intelligent Safety System)
Should the gate hit an obstacle while it is performing a close cycle, or be restricted in some manner, it
will automatically reverse. The amount of force the gate should encounter before reversing is automatically
adjusted by the control system during the initialisation of the automatic opener. The gate will also stop
if restricted whilst opening. The Safety Obstruction Force should be checked at least once a month. See
installation manual for instructions.
1. Features
Thank you for purchasing the NES-24V2 NeoSliderTM
from Automatic Technology. Designed for residential
sliding gates by our world renowned team of
engineers, this unit will give years of smart,
simple and secure operation. Listed below
are some of the many features.

Owner Installation Instructions NeoSliderTM - Sliding Gate Opener NES-24V2 5
Status Indicator
The LCD console display screen indicates through text the status of the NeoSlider™.
When the MAIN SCREEN is displayed, the current position of the gate or the result
of the last movement can be viewed. The display also shows the countdown timer
for Auto-Close operations. Any active input will also be displayed along with the
state of various features such as periodic service, battery backup operation and
vacation mode.
Control of Lock and Lights
The incorporated controller has dedicated outputs for operating an electric lock
and warning or courtesy lights. The timing of these outputs can be adjusted to suit
your needs. In addition a button on a remote transmitter can be coded to operate
the light output.
Extensive Operating Modes Via Control Inputs And Remote Control
The integrated controller can be configured to operate in many different ways via the
seven (7) control and safety inputs which include SB, OPEN, STOP, CLOSE, OSC, SWIPE
and PEDESTRIAN.
Operation is provided with each transmitter’s button being able to be configured to operate
one of OSC, PEDESTRIAN, SWIPE, CLOSE, OPEN, STOP, LIGHT or VACATION functions.
The functionality of the transmitter is further enhanced by four (4) Auto-Close modes, three (3) PE
Beam response modes and two (2) pedestrian response modes.
SmartSolar™ and Battery Backup Compatibility (optional)
The gate opener can be fitted with a SmartSolar™ or Battery Backup kit for operation in the event of a power
outage, or where mains power access is not available.
Manual Operation
The gate opener is equipped with a unique manual disengaging device. If the power to the gate opener is
disrupted for any reason, the gate can be disengaged via a keylock located on the operator, allowing you to
manually open or close the gate.

6NeoSliderTM - Sliding Gate Opener NES-24V2 Owner Installation Instructions
2. Control Board Layout
26
V+
0V
SB2(SafetyBeam(2),two,threewireor
wireless)
SB1(SafetyBeam(1),two,threewireor
wireless)
0V
OPN Programmable N/O or N/C
input terminal
STP Programmable N/O or N/C
input terminal
CLS N/O input terminal
OSC N/O input terminal
SWP N/O input terminal
28
29
13
30
30
01
02
03
04
05
06
07
08
09
10
11
12
Fig 2.1
PED N/O input terminal
0V
V+
OUT 2 (optional relay
module coil drive)
V+
OUT 1 N/C relay contact
Engage sensor microswitch input
Console Previous button
Console Up/Open button
Console Next button
13
Console Exit button
Console Down/Close button
Console SET button
Antenna connector
Console display
PG3 programmer connector
Motor connector
24VAC input connector
10 AMP slow blow fuse
Standby battery charger/solar
connector
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
01
02
03
04
05
06
07
08
09
10
11
12
27
15
17
20
22
18
25
14
16
19
21 23
24
26

Owner Installation Instructions NeoSliderTM - Sliding Gate Opener NES-24V2 7
3. Set Up Requirements
Fig 3.1
3.1 Kit Contents
3.2 Choosing your Set up
The NeoSlider™ can be set up in various ways and therefore may require
additional items. Common Set ups are as follows;
ITEM DESCRIPTION QTY ORDER
CODE
1 DRIVE UNIT NES-24V2 1 60109
2 TRIO-CODE 4B PTX-5V2 TRANSMITTER 2 61160
3 ACCESSORY ACTUATOR PACK 2 61463
4 RESISTOR 5K6 2 65882
1
2
3
4
Set Up Items Required
Automated Set Up Drive Unit and transmitter
Automated Set Up with
Safety Beams
Drive Unit, transmitter and safety beams (optional)
CAUTION: Cables which have a green/yellow coloured
insulation are for earthing purposes only. Never use these
cables for any other purpose.
IMPORTANT WARNING!
A qualified electrician must perform
the installation where 240V AC
power is used.

8NeoSliderTM - Sliding Gate Opener NES-24V2 Owner Installation Instructions
The Automatic Technology NeoSlider™ sliding gate opener is
designed to operate most residential sliding gates. The gates must
be in good working condition and should operate freely by hand.
4.1 Initial Checking
Before commencing installation of the NeoSlider™, check the
following:
a. The gate moves freely and easily by hand for the full opening
and closing travel.
b. The mounting point must be solidy constructed, e.g concrete,
brick or steel, and must be capable of withstanding the full force
applied to the gate.
c. Select a suitable location for mounting the drive unit. This
position is usually established by fully opening the gate and
mounting the drive unit within a suitable distance of the gate
edge.
d. A weather-proof 240v 10 amp power outlet must be located
within one (1) metre of the NeoSlider™ mounting point.
e. If Safety Beams are to be installed, provision for underground
cabling should be made from one side of the gateway to the
other.
4.2 Mounting the Drive Unit
The NeoSlider™ mounting holes are slotted for fine adjustment of
pinion gear and gate rack alignment. Follow the procedure below
to ensure final adjustments can be made later.
We recommend that four 8mm (5 /
16”) or 10mm (3
/
8”) loxins and
bolts are used to secure the Drive Unit into position. These loxins
usually require a 16mm (5 /
8”) masonry drill bit (if drilling concrete).
a. Prior to mounting the NeoSlider™, determine the distance from
the gate to the outer edge of the rack (i.e. the rack width) and to
the datum line (see Fig. 4.2 and Fig. 5.1). If using an Automatic
Technology plastic rack, the width is 40mm. If using a different
brand of rack, please ensure it is Module 4 and then confirm the
width, as this will vary.
b. Mark a line parallel to the face of the gate for the mounting holes.
The distance from the gate is determined by the formula (38mm
+ Rack Width). Therefore, if using an Automatic Technology
rack, the distance is 78mm. Otherwise, if using a non-Automatic
Technology rack, add your rack width (and spacers if required)
to the 38mm (see Fig. 4.2).
c. Another 100mm back, mark another line parallel to that
described in point 2 for fixing. (see Fig. 4.2).
d. Open the gate to the desired open position. Mark a line at a
right angle to the gate 120-150mm from the open edge of the
gate for the mounting holes.
e. Then mark another line 268mm parallel to this line (see Fig. 4.2).
f. Place the Drive Unit in position where the lines intersect to check
the mounting position. If satisfied with the position, remove the
Drive Unit.
g. Drill the four mounting holes where the lines intersect.
h. Hammer the loxins into position, place the NeoSlider™ and fix
with the four bolts. Remember when tightening the bolts to
allow fine adjustement of the NeoSlider™ later on.
4. Drive Unit Installation
IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION
Warning: Incorrect installation can lead to severe injury.
Follow ALL installation instructions.
Fig 4.1
Cover
release
screw
Disengage lever
Cover
release
screw
Fig 4.2
4.3 Installing antenna
Mount the antenna at or above the height of the gate or fence
(whichever is higher) for optimal reception. Do not cut the coaxial
cable.

Owner Installation Instructions NeoSliderTM - Sliding Gate Opener NES-24V2 9
5. Rack & Limit Actuator Installation
5.1 Mounting rack to gate
A strong base on the gate is required for mounting the rack.
a. Manually open the gate and place a rack section to mesh with
the pinion gear on the Drive Unit. Mark the top of the rack.
Move the gate and mark the rack for the entire length of the
gate.
b. Position the top edge of the rack on this line and mark the
centres of the rack’s mounting slots. The first section of rack
should start 20mm from the edge of the gate.
c. Drill and tap for 6mm (¼”) screws.
d. Once the first section of the rack is mounted, check that it
meshes with the NeoSlider™ pinion gear.
e. When joining subsequent sections of rack, check the mesh by
placing a spare section upside down (teeth facing upwards) and
putting it into mesh with the racks being joined (Fig. 05).
f. Tighten the racks. This will ensure that the NeoSlider™ pinion
can run along the racks without obstruction.
Rack
width
Gate
Rack
Drive
gear
Datum line
To top of pinion
To bottom of
rack tooth
Maximum height of rack
Fig 5.1 Fig 5.2
Mounting
holes
M4 x 10 screws
and washers
Actuator mounting
block
M4 x 30 screws
Fig 5.3
5.2 Fixing limit actuator to rack
a. Manually open the gate to the open position and mark this on
the gate rack under the actuating arm.
b. Manually close the gate to the closed position and mark this on
the gate rack under the actuating arm.
c. Place start of limit actuator at marked position and move it 5 to
10mm towards the centre of the gate. Align the face of the limit
actuator with the side of the rack and screw the limit actuator
to the rack (Fig. 06).
d. Re-check limit positions by manually opening and closing the
gate, checking to see that the limit is activated at the desired
open and close position. If neccessary, make adjustments by
sliding the actuator in the required direction. When the final
settings are established, tighten the limit actuator screws - each
actuator must be secured with two (2) screws.

10 NeoSliderTM - Sliding Gate Opener NES-24V2 Owner Installation Instructions
6. Programming The NeoSliderTM
6.1 Common Programs
The two most common programs are;
Program Menu’s required Function Section
Automated Set Up Menu 10.1 Setting the Limits 8.1
Safety Obstruction Force 9.1 and 9.2
Menu 1 Coding the Transmitter 10.1
Automated Set Up with
Safety Beams
Menu 10.1 Setting the Limits 8.1
Safety Obstruction Force 9.1 and 9.2
Menu 1 Coding the Transmitter 10.1
Menu 3 Auto Close Times 13.2, 13.3 and 13.4
NOTE: Fitting Safety Beams enables the Auto-Close feature to become active.
CAUTION: Before plugging the gate control system
in, check the power cord for damage and ensure it
cannot become entangled in any moving parts
6.2 Powering up the NeoSliderTM
a. After checking the initial wiring, apply power to the NeoSlider™.
The controller will go through a startup sequence displaying
the STARTUP SCREEN which indicates the controller type and
firmware version (Fig. 6.2). After a short delay the MAIN SCREEN
will be displayed.
b. If this is the first time the NeoSlider™ has been used, the MAIN
SCREEN should indicate that the limits are not set (Fig. 6.3). If the
display shows that some input is active then rectify the situation
before proceeding. If a default setting is to be changed it should
be done now before setting the travel limits.
Fig 6.2
Fig 6.3
Fig 6.1
A.T.A NES-24V2
Firmware #.##
Limits not Set!
Press <> to access MENUS
Start up screen
Main screen

Owner Installation Instructions NeoSliderTM - Sliding Gate Opener NES-24V2 11
Fig 6.2
Fig 6.3
Fig 6.1
WARNING: When using Safety Beams, the gateway must be clear of all obstructions and persons at all times. The
location of the beams and manner in which it is installed might not give safety protection at all times. Check to
make sure that the height of the beam and type used give maximum protection possible
WARNING: Tampering with Safety Beams could result in serious personal injury and/or property damage and will
void the warranty.
7.1 Installation of Safety Beams to the NeoSliderTM
a. Follow the Installation Manual provided with the Safety Beam to correctly
install the Safety Beam.
b. By default the NeoSlider™ will take two wire safety beams.
c. Ensure you program the NeoSlider™ to idenitfy what type of Safety
Beam or combination of Safety Beams you have installed.
i. Press NEXT to Navigate to Menu 7
ii. Press SET to display Menu 7.1 (for SB1).
iii. Ensure the Safety Beam type is set to two wires.
iv. Press SET to accept the selection.
v. Repeat the same process for Menu 7.2 (SB2) if installed.
NOTE: Wireless Safety Beam functionality is equivalent to 2 WIRE Safety
Beams
NOTE: The Power control for one or both three wire beams is controlled via
OUT 1 or OUT 2. To use the OUT 1, connect black wire from SB to OUT 1.
To enable power control from OUT 1, go to Menu 7.13 and change OUT1
mode to 3 wire SB 0V.
NOTE: In the case that OUT 1 is used for some other function, OUT 2 can
be used to control 3 wire beams power. Connect the black wire from SB to
OUT 2, then change the OUT 2 mode in Menu 7.14 to 3 wire SB 0V.
7. Safety Beams
7.2 Safety Beam Failure Emergency Close (SBFEC)
When the user finds that they are unable to move the gate and suspect that it is due to a faulty SAFETY BEAM they
can attempt to enter Safety Beam Failure Emergency Close mode by pressing and holding a pre-coded button on
the remote control or OPEN/CLOSE button on the console for more than five seconds. the gate will start closing.
See Appendix C Menu 7.16.

12 NeoSliderTM - Sliding Gate Opener NES-24V2 Owner Installation Instructions
8. Setting Limits
The NeoSliderTM has the alternate ability to set travel limits using
a TrioCodeTM128 transmitter, allowing free movement around the
gate to better assess the desired limit positions. In order to use a
transmitter, it must first have at least one of its buttons coded to the
gate controller. The function assigned to the transmitter’s buttons
is of no concern here as the buttons are temporally assigned to
OPEN, CLOSE and SET (Fig. 8.1).
NOTE: Gate should be moved manually to fully open position.
When re-engaging opener, nudge gate until click is heard to
confirm pinion gear has engaged fully.
8.1 Setting Travel Limits
Navigating to “code transmitter” menu
a. Press NEXT to navigate to Menu 1.
b. Press SET to enter the code set procedure (Fig. 8.2).
Storing Transmitter Code
c. Controller will prompt to press one of the transmitter’s Button.
d. Press the transmitter button you wish to use to operate the
gate opener (e.g. button 1) .
e. Press the same transmitter button again as prompted by
display.
f. Press the SET button to store the transmitter.
Navigating To “Set Gate Travel Menu”
g. Press PREV to navigate to Menu 10.
h. Press SET to display MENU 10.1.
i. Press SET two times to enter the limit setting procedure. Follow
LCD prompts.
8.2 Setting the left/right installation side settings
a. Select left or right installation side by pressing open button for the
correct side (Fig. 8.2).
b. Press SET to confirm.
8.3 Setting close travel limit
a. Press and hold Button 4 on the transmitter to close the gate
i. If the gate is closed too far, press Button 1 to “inch” the
gate towards open.
ii. When happy with the close limit position, press Button 2 to
store this in the memory.
NOTE: Limit will not be accepted unless the gate is driven in the
close direction.
8.4 Setting open travel limit
a. Press Button 1 to open the gate.
b. If the gate is opened too far, press Button 4 to “inch” the gate
towards close
c. When happy with the open limit position, press Button 2 on the
transmitter to store into memory..
NOTE: Limit will not be accepted unless the gate is driven in the
open direction.
WARNING: The gate will automatically close and
open once next step is performed. Ensure that no
persons or objects are in the gates path
d. The gate will now automatically close and open to calculate the
safety obstruction settings.
Fig 8.1
Fig 8.2
Button 1
(Inch Open)
Button 4
(Inch Close)
Button 2
(Set)
Menu 1
Code Transmitter
PRESS
8.5 Automatic limit adjustment and load profile
After a brief pause, the controller will automatically close and open
the gate several times. This adjusts the speed at which the limits are
approached and helps to learn the normal load profile of the gate.
When the setup is complete, the MAIN SCREEN will be displayed
with the gate shown to be OPEN. The Gate can now be used.
NOTE: Do not press transmitter during limit adjustment process.
8.6 Pedestrian access position
After completing the above procedure, the Pedestrian access
position is automatically set to a position which is five (5) seconds
from the fully closed position of the gate. The position can be
manually set by following the SETTING PEDESTRIAN POSITION
procedure (See Section 12).
8.7 Errors during setting of travel limit
During the above procedure, many error checks are preformed. If an
error is detected, a message will be displayed indicating the error.
8.8 Recalculate Force Margins
a. Reprofiling is a simplified way of re-learning the travel
characteristic of a previously setup Limit Switch travel installation.
Re-profiling can be used when the travel characteristics of the
gate change due to mechanical adjustments etc.
b. To initiate a re-profile simply locate “MENU 10.2 Reprofile Travel”
WARNING: The gate(s) will automatically close and
open. Ensure that no persons or objects are in the
gates path.
c. Press SET then follow the prompts. The gate will start to move
and re-calculate force margins. The gate can move between the
open and close limit positions up to two (2) times (depending on
the position of the gate and the power up condition).
d. A single beep will be heard once the process is complete and
setup complete message will be displayed
IMPORTANT NOTE:
Only TrioCodeTM128 Technology
Transmitters are compatible with
this product.

Owner Installation Instructions NeoSliderTM - Sliding Gate Opener NES-24V2 13
9. Safety Obstruction Force Test
WARNING! Take care when testing or adjusting the Safety
Obstruction Force. Excessive force may cause SERIOUS
PERSONAL INJURY and/or PROPERTY DAMAGE.
9.1 Testing Close Cycle
a. Press the OPEN button to open the gate.
b. Place a piece of timber approximately 40mm wide on the ground
directly next to the closing pilon / fence (Fig. 9.1).
c. Press the CLOSE button to close the gate. The gate should strike the
object and start to re-open.
9.2 Testing Open Cycle
a. Press the CLOSE button to close the gate.
b. Press the OPEN button to open the gate. When the gate reaches
the half open point, grab the side rail of the gate firmly and the gate
should stop.
c. If the gate does not reverse readily when closing, or stop when
opening, the force may be excessive and need adjusting.
WARNING! If the gate fails these tests, put the opener
into manual mode, only operate the gate by hand and call
for service.
Fig 9.1
40mm Block of wood
Safety Obstruction Force
The Safety Obstruction Force is calculated automatically during setup.
Adjusting this is normally only necessitated by environmental conditions
such as windy or dusty areas, and areas with extreme temperature
changes.
9.3 Force Pressure For Close and Open Cycle.
Navigating To “Current Trips”
a. Press NEXT or PREV to navigate to Menu 2 Current Trips.
b. Press SET (Fig.9.2)
c. MENU 2.1: CLOSE Margin is displayed (Fig. 9.3).
d. Press UP arrow to increase or DOWN arrow to decrease the value.
e. Press SET to save the new value.
f. Test the force again as per “Safety Obstruction Force Test” in Section
9.1.
9.4 Reprofiling Travel
a. Reprofiling is a simplified way of re-learning the travel characteristic
of a previously setup Limit Switch travel installation. Re-profiling can
be used when the travel characteristics of the gate changes due to
mechanical adjustments etc. To initiate a re-profile, simply locate
“MENU 10.2 Reprofile Travel”, press SET and follow the prompts.
The gate will start to move and re-calculate force margins. The gate
can move between the open and close limit positions up to two
(2) times (depending on the position of the gate and the power up
condition).
b. A single beep will be heard once the process is complete.
c. Test the force again as per “Safety Obstruction Force Test” (Section
9.1 and 9.2).
Menu 2
Current Trips
PRESS
Close Margin
(Amps) 0.7
PRESS
Fig 9.2
Fig 9.3

14 NeoSliderTM - Sliding Gate Opener NES-24V2 Owner Installation Instructions
10. Coding Transmitter
NeoSliderTM can store up to thirty (30) transmitters in its memory.
Each transmitter can be allocated an alpha-numeric ID label up to
eleven (11) characters in length and each button can be assigned
to one of several control functions. The settings for a transmitter
are represented in (Fig. 10.1). It shows the transmitter’s store
number, ID label or serial number and the functions assigned to
each of its four buttons. To toggle between ID/SN display, press
UP/DOWN with the cursor on the ID/SN indicator. The procedures
below code, delete, replace, edit and copy transmitter records.
10.1 Coding Transmitter Button
Navigating To Menu 1 “Code Transmitter”
a. Press NEXT to navigate to Menu 1 (Fig. 13.2).
b. Press SET to enter the code set procedure.
Storing Transmitter Code
c. The controller will prompt to press one of the transmitter’s
buttons.
d. Press the transmitter button you wish to use to operate the
Gate Opener (e.g. button 1) (Fig. 10.3) .
e. Press the same transmitter button again as prompted by the
display (Fig. 10.4).
10.2 Selecting Function Of The Button
The controller will now show the transmitter’s record, with a
cursor on the field for the button being coded (Fig. 10.5).
Use UP/DOWN arrows to select the function for the button.
Available functions:
VAC (Vacation Mode) LGT (Courtesy Light)
STP (Stop) OPN (Open)
CLS (Close) SWP (Swipe)
PED (Pedestrian access) OSC (Open/Stop/Close)
OFF (No action)
Press SET to save the settings or EXIT to abort without saving
(Fig. 10.6).
10.3 Returning To Main Screen
The “Code Transmitter” menu will now be shown. Press EXIT to
return to the MAIN SCREEN and test the transmitter.
Fig 10.1
Fig 10.2
Fig 10.3
Fig 10.4
Fig 10.5
Fig 10.6
12
3
ID
Name/SN
OSC PED LGT VAC
I.D label/Serial number
Button 4 function
Button 3 functionButton 2 function
Button 1 function
Store number
ID/SN display indicator
Menu 1
Code Transmitter
PRESS
Press Tx’er
Button LIST> PRESS
Press Tx’er
Again! VIEW> PRESS
# 1 [ No Name ]
OSC OFF OFF OFF
PRESS
PRESS
# 1 [ No Name ]
OSC OFF OFF OFF
PRESS
IMPORTANT NOTE:
Only TrioCodeTM128 Technology Transmitters
are compatible with this product.

Owner Installation Instructions NeoSliderTM - Sliding Gate Opener NES-24V2 15
10. Coding Transmitter
Fig 10.1
Fig 10.2
Fig 10.3
Fig 10.4
Fig 10.5
Fig 10.6
11. Remotely Coding Transmitters
PRESS
If a TrioCodeTM128 transmitter is already coded into the opener, additional
TrioCodeTM 128 transmitters can be coded without being in direct contact
with the NeoSliderTM.
NOTE: Only the function of the existing TrioCodeTM128 Transmitter
button can be assigned to new transmitter. Please read instructions prior
to proceeding - there is a time-out facility for security reasons.
11.1 Selecting The Function To Be Coded
a. Using the existing transmitter, operate the gate with the transmitter
button which has the function to be coded (Fig. 11.1) (e.g. Button 1
has been coded with the OSC function assigned).
b. If the button’s function activates the gate (PED, SWP, OSC, CLS, STP or
OPN) wait for the gate to complete its cycle.
11.2 Activate Remote Code Set Mode
a. Use a small pin to press and hold through the Coding Hole of the existing
transmitter for 2 seconds (Fig. 11.2).
b. Within 10 seconds, press the button on the new transmitter you wish to
code for 2 seconds (Fig. 11.3).
c. Press the same button again (within 10 seconds) for confirmation.
d. Test Operation. The new transmitter button should now function as the
existing transmitter.
PRESS
Existing
transmitter
New
transmitter
Existing
transmitter
Fig 11.1
Fig 11.2
Fig 11.3
NOTE: When a transmitter is remotely coded, its ID label is set to that
of the existing transmitter. If the existing transmitter does not have an ID
label assigned, then the ID label of the new transmitter is set to: R/C Tx
###, where ### is the existing transmitters store number. This ensures that
the originator of any remotely coded transmitter can be identified.
11.3 Removing the Battery From the Transmitter
(Battery Type: 3V Lithium Battery CR2032).
Use a non-metallic object (e.g. pen) to remove the battery. (Fig. 11.4).
To test the battery is working, press and hold a transmitter button;
(Fig.11.5).
Light Status Battery Status
Solid OK
Flashing Requires replacement
No light Requires replacement
REPLACE BATTERY WITH CR2032 ONLY
Fig 11.4 Fig 11.5
Use a pen
to push the
battery down
through the
side opening
to release
battery

16 NeoSliderTM - Sliding Gate Opener NES-24V2 Owner Installation Instructions
NeoSliderTM can be instructed, via its pedestrian control feature,
to partly open and provide pedestrian access but prevent vehicle
access.
NOTE: Before setting the pedestrian access position the gate
must be in the fully closed position. As with the Setting Travel
Limit procedure, a transmitter can be used to complete the
pedestrian position setting procedure.
NOTE: The pedestrian default position is set at five (5) seconds
from fully closed position and can be changed as follows:.
12.1 Setting pedestrian position
Navigating to “Menu 10.3 Set Pedestrian”
a. Press PREV to navigate to Menu 10.
b. Press SET - MENU 10.1 is displayed.
c. Press NEXT to go to MENU 10.3.
d. Press SET to enter Set Pedestrian procedure (Fig. 12.1).
To Set pedestrian position
a. Press OPEN to change the pedestrian access position time
(Fig. 12.2).
b. Press SET to record new time.
c. Press transmitter coded for pedestrian function to test.
12.2 Pedestrian Position Set
The controller will return to the MAIN SCREEN with the gate
status shown as being in pedestrian access mode (Fig. 12.3).
12.3 Error Displays
During the above procedure many error checks are performed. If
an error is detected, a message will be displayed indicating the
error.
12. Setting Pedestrian Position
Fig 12.1
Fig 12.2
MENU 10.3
Set Pedestrian
PRESS
Ped’n Opening
Time 5
PRESS
PRESS
Ped’n Access
Press <> to Access MENU
Fig 12.3

Owner Installation Instructions NeoSliderTM - Sliding Gate Opener NES-24V2 17
Fig 12.1
Fig 12.2
Fig 12.3
WARNING! The Auto-Close function is not available
unless Safety Beam is installed.
13.1 Setting Up Standard Auto-Close
Menu 3. Auto-Close Times
Auto-Close mode is a function that automatically closes the gate a
preset time after the Safety Beam recognise that a vehicle has left the
gateway. The Auto-Close timer only starts after the Safety Beam path
is broken and the Auto-Close timer has been set. If the Safety Beam
path is not broken, the gate will remain open until the path is broken.
If the opener incurs a physical obstruction (i.e. not from the Safety
Beam) while closing, the gate will re-open and not Auto-Close until
the Safety Beam path is broken again.
Menu 3.1 Auto-Close
This mode is selected by entering a non-zero time for the STD Auto-
Close parameter. When selected, the gate will Auto-Close after being
fully opened (except when the gate has reversed to the open position
after a motor obstruction or overload unless A/C after open and/or
close Obstruction are selected). Countdown is suspended by: S.B.,
OPN or SWP input being active. The countdown is aborted if the STP
input is activated. If the gate is already open and the OPN or the SWP
input is activated, then the countdown will start.
13.2 Safety Beam Triggered Auto Close
Menu 3.2 (SB AC Trig)
This mode is selected by entering a non-zero time for the “Safety
Beam Auto-Close” parameter. This mode is used to Auto-Close the
gate but only after an object has passed through the gateway and has
triggered the Safety Beam input. Any Safety Beam or combination of
Safety Beams can be configured to activate Safety Beam Auto-Close
mode and combinations are:
One Beam only
i. Safety Beam 1
ii. Safety Beam 2
Either Beam
i. Safety Beam 1 or Safety Beam 2
Combination
ii. Safety Beam 1 and Safety Beam 2
iii. Safety Beam 2 then Safety Beam 1
NOTE: The swipe input can be used to clear the Safety Beam triggered
status so that the Safety Beam input must be activated again before
the countdown will start. As with the other Safety Beam modes, the
STP input will abort countdown and the OPN and SWP inputs will
restart the countdown if the gate is OPEN.
13. Auto-Close Mode
13.3 Pedestrian Auto-Close
Menu 3.3 Safety Beam Auto-Close
This mode is selected by entering a non-zero time for the “Safety
Beam Auto-Close” parameter. This mode is used to Auto-Close the
gate but only after an object has passed through the gateway and
has triggered the Safety Beam input
Menu 3.4 Pedestrian Auto-Close
This mode is selected by entering a non-zero time for the “Ped’n
A/C” parameter. When selected, the gate will Auto-Close after being
opened for pedestrian access unless it was following a reverse from
an obstruction.
Menu 3.5 (Safety Beam) Pedestrian Triggered Auto-Close
This mode is selected by entering a non-zero time for the “Safety
Beam Pedestrian Auto-Close” parameter. Any Safety Beam or
combination of Safety Beams can be configured to activate Safety
Beam Auto-Close mode and combinations are:
One Beam only
iv. Safety Beam 1
v. Safety Beam 2
Either Beam
i. Safety Beam 1 or Safety Beam 2
Combination
ii. Safety Beam 1 and Safety Beam 2
iii. Safety Beam 2 then Safety Beam 1
Menu 3.6 (Safety Beam) Pedestrian Auto-Close
This mode is selected by entering a non-zero time for the “Ped’n
A/C” parameter. When selected, the gate will Auto-Close after being
opened for pedestrian access but only after an object has passed
through the gateway and has triggered the Safety Beam input.
13.4 Auto-Close After Obstruction
Two parameters are provided to enable the Auto-Close feature to be
activated after obstructions and power up. Normally the Auto-Close
feature is not enabled after obstructions for safety reasons. Safety
Beams must be used for these features to be activated.
Menu 3.7
This mode enables the Auto-Close feature to be activated when a
close obstruction occurs (requires Safety Beams).
Menu 3.8
This mode enables the Auto-Close feature to be activated when an
open obstruction occurs.
Menu 3.9
This mode enables Auto-Close feature after power up.

18 NeoSliderTM - Sliding Gate Opener NES-24V2 Owner Installation Instructions
14. Accessories Installation
LIGHT RELAY MODULE
POWER SUPPLY
V+
0V
SAFETY B2
SAFETY B1
OV
OPEN
STOP
CLOSE
OSC
SWIPE
PEDESTRIAN
OV
V+
OUT2
V+
OUT1
Wiring Output1 And Output2
Outputs 1 and 2 are used to control a lock, Light or Safety Beam
power. Which output is to control which function and the way it
is controlled is programmable. If using these outputs make sure
that the functions are configured for correct operation prior to
setting the travel limits. OUTPUT1 or OUTPUT2 is used to activate
an optional external relay module (RO-1) which in turn is used to
switch the load.
14.1 Fitting Solenoid Or Magnetic Locks
Install the lock mechanism on the gate as per the manufacturers
instructions. See Fig. 14.1 for the wiring diagram.
Menu 4. Lock Times
Lock output can be programmed for both hold and pulse mode.
The operation of the lock can be programmed to activate prior to
the gate and behave differently on open cycles to that on close
cycles.
a. Press NEXT or PREV on the wall control unit to navigate to
Menu 4 Lock Times.
b. Press SET to select the sub menu.
c. Press NEXT or PREV to navigate through the sub menu.
d. Press OPEN to increase or CLOSE to decrease the time.
e. Press SET to save the new time.
f. Press the EXIT button two times to exit and test the locks
operation.
Pulse Lock
LOCK RELAY MODULE
POWER SUPPLY
V+
0V
SAFETY B2
SAFETY B1
OV
OPEN
STOP
CLOSE
OSC
SWIPE
PEDESTRIAN
OV
V+
OUT2
V+
OUT1
Fig 14.1
Fig 14.2
14.2 Fitting Courtesy Lights
An AC or DC courtesy light can be activated via an output on the
gate opener control board. Connect the light as per the diagram.
(Fig. 14.2)
WARNING: A qualified electrician must perform the
installation where 240V AC power is used.
Menu 5. Light Times
a. Press NEXT or PREV on the wall control unit to navigate to Menu
5 Light/Lock Times.
b. Press SET to select the sub menu.
c. Press NEXT or PREV to navigate through the sub menu.
d. Press OPEN to increase or CLOSE to decrease the time.
e. Press SET to save the new time.
f. Press the EXIT button two times to exit.
g. Test the light operation.

Owner Installation Instructions NeoSliderTM - Sliding Gate Opener NES-24V2 19
Fig 14.1
Fig 14.2
Technical Specifications
Protection rating: IP33
Input voltage: 230V - 240V AC 50Hz
Transformer primary voltage: 230V/240VAC
Secondary voltage: 24V AC 150 VA
Controller voltage: 24V DC
Motor type: Permanent Magnet Direct Current
Motor voltage: 24V DC
Maximum pulling force: 200N
Maximum gate opening: 1, Width:
Weight:
10m
250kg
Opener maximum
Opening/closing run time:
30 seconds
Receiver type: TrioCode™128
Receiver code storage capacity: 30 x 4 Button Transmitter Codes
Transmitter frequency: 433.47, 433.92, 434.37 MHz
Coding type: Hopping Code
No. of code combinations: Over 100 billion random codes
Code generation: Non-linear encryption algorithm
Transmitter battery: CR2032
NOTE:
1. The maximum gate size that the NeoSlider™ can be installed on is 10m wide and 250kg. The gate must be well balanced.
A person should be able to move the gate manually with very little effort (15kg force max.) in case of an emergency.
2. Intermittent operations may occur in areas which experience very strong wind gusts. A strong wind puts extra pressure
on the gate and tracks which may in turn trigger the safety obstruction detection system intermittently.
NOTE:Specifications are subject to change without notice.
15. Specifications

20 NeoSliderTM - Sliding Gate Opener NES-24V2 Owner Installation Instructions
Symptom Possible cause Remedy
Gate will not operate Mains power not switched on. Switch on mains power.
Opener motor is disengaged Check that the motor is engaged for automatic
operation
Gate is obstructed. Remove obstruction.
The opener is in “Vacation Mode” Turn off “Vacation Mode”(Appendix DMenu 7.4).
Gate starts to close but
automatically reverses to open
position
Adverse weather conditions (wind
or cold) causing gate to stiffen and
become tight in the tracks.
Increase force margin setting (Section 9.4)
Possible obstruction in the gateway
triggering Safety Beams.
Remove obstruction
Gate operates from opener but
not from transmitter
Transmitter code not stored in
memory.
Code transmitter in to openers memory.
(Section 10.1)
Transmitter does not contain
TrioCode™ 128 Technology
Check the transmitter. It should have grey buttons
and the model number should display V2. Contact
dealer for support if otherwise.
Flat battery in transmitter Replace battery (Section 11.3)
Antenna behind structure (gate or
fence) or not in line of sight
Ensure Antenna is in line of sight (Section 4.2)
Gate does not close with
transmitter
Safety Beam not working properly. Make sure Safety Beams are operational. and no dirt
is on the lens.
Gate will not close fully. Gate limit positions need to be
reset.
Reset limits positions.
Gate obstructed and reverses Clear obstruction or adjust force margin
(Section 9.3)
Gate will not open fully. Gate limit positions need to be
reset.
Reset limits positions. (Section 8)
Gate obstructed. Clear obstruction or adjust force margin
(Section 9.3)
Auto-Close not working Safety Beam not installed. Install Safety Beam. (Section 6)
Safety Beam or wiring faulty. Repair Safety Beam or replace wiring.
Safety Beam not aligned correctly. Re-align optics.
Safety Beam is obstructed. Remove obstruction from path of Safety Beams.
Gate obstructed when closing. Remove obstruction.
Auto-Close time not set. Set Auto-Close times (Section 13.3).
Auto-Close mode not set Set Auto-Close mode. (Section 13.2)
16. Troubleshooting