Autonics MP-XGT Installation instructions

© Copyright Reserved Autonics Co., Ltd. iii
MP-XGT(RS485)
Technical Support Manual

ii © Copyright Reserved Autonics Co., Ltd.

Preface
© Copyright Reserved Autonics Co., Ltd. 3
Preface
Thank you very much for selecting Autonics products.
Please familiarize yourself with the information contained in the Safety Precautions section
before using this product.
This user manual contains information about the product and its proper use, and should be kept
in a place where it will be easy to access.

Technical Support Manual Guide
4 © Copyright Reserved Autonics Co., Ltd.
Technical Support Manual Guide
Please familiarize yourself with the information in this manual before using the product.
This manual provides detailed information on the product's features. It does not offer any
guarantee concerning matters beyond the scope of this manual.
This manual may not be edited or reproduced in either part or whole without permission.
This manual is not provided as part of the product package. Please visit our home-page
(www.autonics.com) to download a copy.
The manual's content may vary depending on changes to the product's software and other
unforeseen developments within Autonics, and is subject to change without prior notice.
Upgrade notice is provided through our homepage.
We contrived to describe this manual more easily and correctly. However, if there are any
corrections or questions, please notify us these on our homepage.

Technical Support Manual Symbols
© Copyright Reserved Autonics Co., Ltd. 5
Technical Support Manual Symbols
Symbol Description
Supplementary information for a particular feature.
Failure to follow instructions can result in serious injury or death.
Failure to follow instructions can lead to a minor injury or product damage.
An example of the concerned feature's use.
※1 Annotation mark.

Safety Precautions
6 © Copyright Reserved Autonics Co., Ltd.
Safety Precautions
Following these safety precautions will ensure the safe and proper use of the product and
help prevent accidents, as well as minimizing possible hazards.
Safety precautions are categorized as Warnings and Cautions, as defined below:
Warning Failure to follow the instructions may lead to a serious injury
or accident.
Caution Failure to follow the instructions may lead to a minor injury or
accident.
In case of using this unit with machinery (E.g.: nuclear power control, medical equipment,
ship, vehicle, train, airplane, combustion apparatus, safety device, crime/disaster prevention
equipment, etc) which may cause damages to human life or property, it is required to install
fail-safe device.
It may cause a fire, human injury or property loss.
The unit must be installed on a device panel before use.
Failure to follow this instruction may result in electric shock.
Do not connect, repair, or inspect the unit while connected to a power source.
Failure to follow this instruction may result in electric shock.
Do not disassemble or modify the unit. Please contact us if necessary.
Failure to follow this instruction may result in electric shock or fire.
Check the terminal numbers before connecting the power source and measurement input.
Failure to follow this instruction may result in fire.
Do not use the unit outdoors.
Failure to follow this instruction may result in electric shock or shortening the life cycle of the
unit.
When connecting the power input or measuring input, make sure to tighten the terminal
screw bolt above 0.74N•m to 0.90N•m.
Contact failure may result in fire.
Use the unit within the rated specifications.
Failure to follow this instruction may result in electric shock or shortening the life cycle of the
unit.
Do not use loads beyond the rated switching capacity of the relay contact.
Failure to follow this instruction may result in insulation failure, contact failure, contact
bonding, relay damage, or fire.
Do not use water or oil-based detergent when cleaning the unit. Use dry cloth to clean the
unit.
Failure to follow these instructions may result in electric shock or fire.
Do not use the unit where flammable or explosive gas, humidity, direct sunlight, radiant heat,
vibration, and impact may be present.
Failure to follow this instruction may result in fire or explosion.

Safety Precautions
© Copyright Reserved Autonics Co., Ltd. 7
Keep dust and wire residue from flowing into the unit.
Failure may result in fire or product malfunction.
Check the polarity of the measurement input contact before wiring the unit.
Failure to follow this instruction may result in fire or explosion.

Safety Precautions
8 © Copyright Reserved Autonics Co., Ltd.

Table of Contents
© Copyright Reserved Autonics Co., Ltd. 9
Table of Contents
Preface ...........................................................................................................................3
Technical Support Manual Guide .....................................................................................4
Technical Support Manual Symbols.................................................................................5
Safety Precautions ...........................................................................................................6
Table of Contents .............................................................................................................9
1System ....................................................................................................... 11
1.1 Version ................................................................................................................ 11
1.2 Connections ........................................................................................................ 11
1.3 Communication cable connection....................................................................... 11
2Communication Setting............................................................................13
2.1 MP5W Setting .....................................................................................................13
2.2 XG5000 Setting...................................................................................................14
3Operation Check .......................................................................................23

Table of Contents
10 © Copyright Reserved Autonics Co., Ltd.

1 System
© Copyright Reserved Autonics Co., Ltd. 11
1System
1.1 Version
Software
Version
Note
Ms Windows Windows 7 —
XG 5000 V4.07 Release : 2016.03.29
1.2 Connections
RS-485 RS-485 RS-485 RS-485
XGK-CPUE MP5W MP5W MP5W MP5W
(XGl-CH2A)
1.3 Communication cable connection
MP5W Cable connection PLC (XGT-XGL-CH2A)
RS – 485 (-) RX -
RX +
RS – 485 (+) TX -
TX +

1 System
12 © Copyright Reserved Autonics Co., Ltd.

2 Communication Setting
© Copyright Reserved Autonics Co., Ltd. 13
2Communication Setting
2.1 MP5W Setting
1st Supply power to the MP5W unit. Press the MODE key to enter parameter setting group.
2nd Enter PARa3 and set the communication settings as below.
Parameter
Display
Setting
Note
Communication address ADDR 01 User setting
Communication speed BPS 38400 User setting
Communication parity bit PRTY NONE Fixed
Communication stop bit STP 2 Fixed
Communication response
waiting time
RSwT 20 User setting
Communication write COmW ENA Fixed
* Hold the MODE key over 3 sec while in setting mode to return to RUN mode.
* Hold the MODE key for 1.5 sec while in setting mode to move to other parameter group.
* Press the MODE key after the setting and it is saved.
* If there is no additional key operation within 60 sec after entering into setting mode, it will
be automatically returned to RUN mode and previous set value will be remained.
* Check that RS485 communication models are only available communication.

2 Communication Setting
14 © Copyright Reserved Autonics Co., Ltd.
2.2 XG5000 Setting
1st Run XG5000, and select [Project] –[New Project] on menu.
Enter project name and select CPU Series and type.

2 Communication Setting
© Copyright Reserved Autonics Co., Ltd. 15
2nd After executing, enter the below contents at XG5000.
* This communication program is only for test. Before using it at field, review and test the
program fully.

2 Communication Setting
16 © Copyright Reserved Autonics Co., Ltd.
3rd Select [Online] – [Connection Settings] to select connection method. This test is connected
via USB. After completing connection, select [Online] – [Mode Switch] – [Stop].
4th At [Online] – [Diagnose] – [I/O Information] , click ‘I/O Sync’. After I/O synchronize, the
settings are set as using module settings.
Connection settings
Settings
Type USB
Depth Local

2 Communication Setting
© Copyright Reserved Autonics Co., Ltd. 17
5th After I/O synchronize, you can check the added communication module below standard
network. Double-click the right communication module.
6th [Standard Settings-Cnet] dialog box appears. At standard settings, set as below.
Item
Setting
Note
Standard
Settings
Channel 2
Communication type RS-485 Fixed
Communication
speed 38400 User setting
Terminating resisters Disable User setting
Station No. 1 User setting
Operation
mode Channel 2 Use P2P

2 Communication Setting
18 © Copyright Reserved Autonics Co., Ltd.
7th At advanced settings, set as below.
Item
Channel 2
Advanced
settings
Data bit 8
Stop bit 2
Parity bit NONE
8th At Project window, select the communication module and [Add Item] – [P2P
Communication] and click ‘OK’.

2 Communication Setting
© Copyright Reserved Autonics Co., Ltd. 19
9th Double-click ‘P2P Channel’ and select ‘Modbus RTU client’ of ‘Use P2P’. Click ‘OK’.

2 Communication Setting
20 © Copyright Reserved Autonics Co., Ltd.
10thBelow P2P channel, double-click ‘P2P block’ and set as below.
CH
P2P
function
Conditional
flag
Command
type
Data type
Destination station
number
2 READ(PV)
M00000 to
M00003
2.
Continuous
WORD
(size: 2)
Enter destination station
(1 to 4)
* Refer to the below table for variable setting for PV and SV.
Click ‘Setting’ to set variable.
* Modbus Mapping Table
Address Type Setting range Factory default
301002(03E9)
PV Present
value -19999 to 99999
301003(03EA)
* Be sure that MP Series requires 2 addresses; 03E9, 03EA for reading present value.