TPS30
TPS20
KT-302H
PTF30
Pressure Transmitter
F-2
A. Recorders
B. Indicators
C. Converters
D. Controllers
E. Thyristor
Power
Controllers
F. Pressure
Transmitters
G. Temperature
Transmitters
H. Accessories
※1: The sensor is sealed structure. It is based on atmospheric pressure 101.3kPa (1.013bar).
※2: The weight includes packaging. The weight in parenthesis is for unit only.
※Environment resistance is rated at no freezing or condensation.
Series TPS30
Pressure type Gauge pressure,
absolute pressure Sealed gauge pressure※1Gauge pressure
Rated pressure
range (MPa)
0 to
0.1
0 to
0.2
0 to
0.7
0 to
1
0 to
2
-0.1 to
0
-0.1 to
0.1
-0.1 to
0.7
-0.1 to
1
-0.1 to
2
0 to
3.5
0 to
5
0 to
10
0 to
20
0 to
40
0 to
50
0 to
60
Expanded analog
output range (MPa)
0 to
0.11
0 to
0.22
0 to
0.77
0 to
1.1
0 to
2.2
-0.1 to
0.01
-0.1 to
0.12
-0.1 to
0.78
-0.1 to
1.11
-0.1 to
2.21
0 to
3.85
0 to
5.5
0 to
11
0 to
22
0 to
44
0 to
55
0 to
66
Max. pressure
range (MPa)
0.6 0.6 3330.6 0.6 33310 20 50 80 120 120 120
Burst pressure
(MPa) 0.6 0.6 3330.6 0.6 33315 30 75 120 160 160 160
Measured
materials Liquid, gas, oil (inappropriate to corrosion environment for stainless steel 316L)
Power supply Voltage output type: 8-36VDCᜡ(ripple P-P: max. 10%) Current output type: 11-36VDCᜡ(ripple P-P: max. 10%)
Permissible
voltage range 90 to 110% of rated voltage
Current
consumption Voltage output type: max. 20mA Current output type: max. 30mA
Response time Max. 1ms
Protection circuit Reverse polarity protection circuit
Output type Voltage output type: 1-5VDCᜡCurrent output type: DC4-20mA
Compensation
temperature -10 to 80℃0 to 80℃
Accuracy Max. ±0.5% F.S. (including linearity, hysteresis, reproducibility)
Linearity Max. ±0.2% F.S.
Hysteresis Max. ±0.2% F.S.
Temp. Zero Shift Max. ±0.1% F.S./10℃(standard), max. ±0.25% F.S./10℃(max.)
Temp. Span Shift Max. ±0.1% F.S./10℃(standard), max. ±0.25% F.S./10℃(max.)
Temperature
characteristics
-
-25 to 100℃: max. ±1.5% F.S.
-40 to 125℃: max. ±2.5% F.S.
Load resistance Current output type: max. 700Ω (supplying 24VDC)
Dielectric strength 500VAC 50/60Hz for 1 minute
Insulation
resistance Over 100MΩ (at 500VDC megger)
Environment
Ambient
temp.
Voltage
output
Head type, DIN43650-A connector type, M12 connector type, DT04-3P connector type: -40 to 125℃, storage: -40 to 125℃
Cable type: -40 to 80℃, storage: -40 to 80℃
Current
output
Head type, DIN43650-A connector type, M12 connector type, DT04-3P connector type: -40 to 85℃, storage: -40 to 125℃
Cable type: -40 to 80℃, storage: -40 to 80℃
Ambient humidity
35 to 85%RH
Fluid temp. -40 to 125℃
Vibration 10g, 20 to 2,000Hz 20g, 20 to 2,000Hz
Shock 100g/6ms 500g/1ms
Tightening torque Max. 10N.m
Protection
structure
Head type, M12 connector type, DT04-3P connector type, cable type: IP67 (IEC standard)
DIN43650-A connector type: IP65 (IEC standard)
Material Stainless steel 316L (head part of head type: aluminium diecasting), connector: polybutylene terephthalate G30,
water-proof rubber: silicon
Connection Voltage output type: +, -, Vout Current output type: +, -
Approval ᜢ
Weight※2
Head type: approx. 330g (approx. 250g)
DIN43650-A connector type, M12 connector type, DT04-3P connector type: approx. 130g (approx. 50g)
Cable type: approx. 200g (approx. 120g)
Specications
