Avalon A6BLWTRCLRWHT User manual

单色印刷
曾平2017-3-31
YL1660S
105克铜版纸
说明书
145*210m m
16163000A12421

Model: A6BLWTRCLRWHT
Self Cle an

DIRECTORY
SAFETY PRECAUTIONS
GETTING STARTED
TROUBLE SHOOTING
MACHINE INSTALLATION
WATER PURIFIER
8
6
2
1
7
9

Self Clean
PART NAME
Please use the product in a place with temperature of 39-100 F and
relative humidity level.
NOTE:
NO. PART NAME NO. PART NAME
Cooling Pilot Lamp
Heating Pilot Lamp
1
2
3
4
5
6
7
Water Collector
Cooling Switch
Heating Switch
Tap of Hot Water
Outlet of Hot Water
1
6
7
9
11
12
14
15
Tap of Cold Water
8
9
10
11
13
Power Cord
Condenser
Top Cover
10
14
16
Self-Cleaning Switch
LED Night Light
8
15
13
12
LED Night Light Switch
2
3
4
16
5
Power/Ozone Pilot Lamp
Water Shortage Pilot Lamp

SAFETY PRECAUTIONS

GETTING STARTED
1. Open the top of the packing case, take out the top foam and its accessories.
2. Put the accessories aside.
This appliance can be used by children aged from 8 years and above if they
have been given supervision or instrucon concerning use of the appliance
in a safe way and if they understand the hazards involved. Cleaning and user
maintenance shall not be made by children unless they are older than 8 and
supervised. Keep the appliance and its cord out of reach of children aged
less than 8 years.
Appliances can be used by persons with reduced physical, sensory, or mental
cappsbilies or lack of experience and knowledge if they have been given
supervision or instrucon concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance.
This appliance is intended to be used in household and similar applicaons
such as: kitchen areas in shops, offices, and other working environments,
hotels, motels, and other residenal type environments, bed and breakfast
type environments, catering, and similar non-retail applicaons.
Do not store explosive substances such as aerosol cans with a flammable
propellant in this appliance.
If the supply cord is damaged, it must be replaced by a special cord assembly
avaiable from the manufacturer or its service agent.
Never turn the machine upside down or lean it more than 45 .
Thermostat has been adjusted. No need to adjust it by yourself. When the
machine is below the freezing point and blocked by ice, the cooling switch be
turned off for 4 hours before turning it on again to connue its operaon.
This machine should not be turned on unl 3 minutes aer turning off the
power switch.

5 Gallon Bole
Powering On Dispenser
Install water bole
1. Open cabinet door.
2. Place probe assembly on probe hanger.
3. Place fresh bole outside of cabinet.
4. Remove enre plasc cap from top of bole.
5. Clean outside of new bole with a cloth.
6. Place probe into bole.
7. Slide collar down unl it clicks in place.
8. Push head down unl tube hits boom of
bole.
9. Slide bole into cabinet and close door.
Plug cord into a properly grounded wall outlet.
At this me the pump will begin to move water
from the bole to the hot and cold tanks. It will
take up to 12 minutes to fill the tanks for the first
me. During this period the pump will run
connuously. This is normal.
Acvate Heang & Cooling
Noce: This unit will not dispense hot or cold water unl the switches
are acvated.
To acvate, push top side of power switches in to start heang and cooling
water.
- If you do not want to heat water, push boom side of red switch in.
- If you do not want to cool water, push boom side of green switch in.
Acvate Self-Cleaning Switch
- Located on back of machine. Press black switch in, hold for 5 seconds and
release to acvate the cleaning cycle.
3 Gallon Bole

5
DISPENSING WATER
This unit has been tested and sanized prior to packing and shipping. During
transit, dust and odors can accumulate in the tank and lines. Dispense and
dispose at least 1 L of water prior to drinking any water.
Dispensing Cold Water
Aer setup, it will take up to 1 hour to get water to maximum cold
temperature. During this me the compressor could run connuously.
This is normal.
1. Posion bole, glass, pitcher or cooking pot below spout.
2. Depress cold water control downward to start cold water flow.
3. Release control once desired fill level is achieved.
Dispensing Room Temperature Water
1. Posion bole, glass, pitcher or cooking pot below spout.
2. Depress normal water control downward to start normal water flow.
3. Release control once desired fill level is achieved.
Dispensing Hot Water
Aer setup, hot water will be available in 15-20 minutes.
1. Posion bole, glass, pitcher or cooking pot below spout.
2. Slide red buon away from you and depress hot water control downward
to start hot water flow.
3. Release control once desired fill level is achieved.
Changing Boles
A flashing red light alerts you when your bole is empty. Replace the bole
as soon as possible.
Noce: Do not dispense hot, cool or cold water if the red light is flashing as
you could empty the tanks and cause the dispenser to overheat.
1. Open cabinet door.
2. Slide empty bole out of cabinet.
3. Remove probe assembly from empty bole. Place probe assembly on
probe hanger.
4. Set empty bole aside.
5. Place fresh bole outside of cabinet. Remove enre plasc cap from top
of bole. Clean outside of new bole with a cloth.
6. Place probe into bole. slide collar down unl it clicks in place. Push
head down unl tubes hit boom of bole.
7. Slide bole into cabinet and close door.
Note: If any error occurs in the heating or cooling process, the indicator light will blink.

6
1. The machine was disinfected before being shipped from the factory. Clean
the dispenser prior to installing a full bole of water for the fist me.
2. Cleaning and draining instrucon:
1)Make sure the power switch in the O(off) posion and unplug the water
dispenser before cleaning.
2)Twist out the two screws, the take down top cover, cold tank cover,
and separator
3)Fill 2.2 L of pure water into cold tank to clean it.
4)Place a large water bucket beneath the drain outlet which is in the back of
the water dispenser, then remove the drain cover and drain the water.
5)Reposion the drain cover, separator, cold tank cover, and top cover aer
draining. Ensure the pipe and wires are connected properly, then you
can use the machine normally.
CLEANING
To avoid accidents, cut off the power supply before operaon according
to the following instrucons.
TROUBLE SHOOTING
Water is leaking.
Unplug dispenser, remove bole and replace it.
No water is coming from the spout.
Make sure the bole is not empty. If empty, replace it.
Make sure to completely depress the push buon controls.
Cold water is not cold.
It takes up to one hour aer setup to dispense cold water.
Make sure the power cord is properly connected to a working outlet.
Make sure the back of the dispenser is at least 20 cm from a wall and
there is free airflow on all 20 cm sides of the dispenser.
Make sure green power switch on back of dispenser is ON.
If water sll isn’t cold, contact an authorized service agent.
Hot water is not hot.
Dispenser is noisy.
It takes 15-20 minutes aer setup to dispense hot water.
Make sure the power cord is properly connected to a working outlet.
Make suer red power switch on back of dispenser is ON.
Make sure the dispenser is posioned on a level surface.

7
Aenon:
1) Cleaning must be performed by someone with experience or an
authorized service agent.
2) The dispenser heats water to a temperature of approximately 185 F.
It can cause severe burns. Please operate it carefully.
3. Sanizing
Mix 4 L of water with 200 g of citric acid crystals, pung the mixture into the
machine making sure the water can flow out of the hot water tap. Switch on
for about 10 minutes. 30 minutes later, drain the liquid,
the power and heat it
o Never disassemble by yourself to
or three mes.
then clean it with water tw
machine. Generally this should be done every six months.
avoid damaging
4. To Remove Mineral Deposits:
MACHINE INSTALLATION
WARNING! To avoid a hazard due to instability of the appliance, it must be
fixed in accordance with the instrucons.
This machine should be sanized with a disinfectant and then cleaned with
water every three months. (See cleaning and draining instrucons.)
1-2. Loosen the screw of the le or right boom angle
as in the picture below.
3. Use the screw to fix the bracket on the le or right
boom angle of the water dispenser.
4. Make a hole on the floor's surface where the water
dispenser will be installed.
5. Fix the bracket on the floor by screwing ghtly.
6. Tighten the screw.
To prevent the machine from swaying or falling, we have
included an oponal bracket. Please install the bracket
accordingly.

If you encounter any issues or have any concerns,
please email us at [e-mail]
or call 1800-256-0695 .
www.avalonproducts.com
Please see our website to learn more about our products