Avantco Collecting broom 1100 User manual

Collecting broom 1100
2018 1
Operator's Manual for Attachment
Collecting broom 1100
Product number
Collecting Broom 1100 A36883
-with side brush A426229
-with side brush and watering system A426231
English
A430125 2018 1 EN 2018-
www.avanttecno.com

Collecting broom 1100 2018 1

Collecting broom 1100 2018 1
CONTENTS
1. FOREWORD ............................................................................................................................................4
Warning symbols used in this manual ............................................................................................................................... 5
2. DESIGNED PURPOSE OF USE.............................................................................................................6
3. SAFETY INSTRUCTIONS FOR USING THE ATTACHMENT........................................................7
3.1 Personal protective equipment........................................................................................................................... 9
4. TECHNICAL SPECIFICATIONS ..........................................................................................................10
4.1 Safety labels and main components of the attachment.................................................................................. 11
5. ATTACHING THE ATTACHMENT ....................................................................................................13
5.1 Connecting and disconnecting hydraulic hoses............................................................................................... 14
5.2 Electric connection................................................................................................................................................ 16
5.2.1 To connect the electric harness of the attachment to the loader ..................................................... 16
6. USING THE BROOM..............................................................................................................................18
6.1 Checks before use................................................................................................................................................. 19
6.2 Operator qualification .......................................................................................................................................... 19
6.3 Operating the broom ........................................................................................................................................... 20
6.3.1 OptiFloat®...................................................................................................................................................... 22
6.4 Emptying the collector ......................................................................................................................................... 22
6.5 Adjusting operating height................................................................................................................................... 23
6.6 Side brush................................................................................................................................................................ 24
6.7 Setting the side brush ........................................................................................................................................... 25
6.8 Water spraying system......................................................................................................................................... 26
6.8.1 Using the water spraying system................................................................................................................ 26
6.9 Transport position ................................................................................................................................................ 27
6.10 Storing the attachment......................................................................................................................................... 28
6.11 Working on uneven ground................................................................................................................................ 28
7. INSTALLING A SIDE BRUSH ...............................................................................................................29
7.1 Qualification requirements for installation work:........................................................................................... 29
7.2 Safety instructions for hydraulic assemblies..................................................................................................... 30
7.3 Tightening hydraulic fittings................................................................................................................................. 31
7.4 Fitting a side brush or changing the installation side...................................................................................... 32
8. MAINTENANCE AND SERVICE ..........................................................................................................35
8.1 Inspection of hydraulic components.................................................................................................................. 35
8.2 Inspection of metal structures............................................................................................................................ 36
8.3 Cleaning the attachment ...................................................................................................................................... 36
8.4 Brush ........................................................................................................................................................................ 36
8.4.1 Side brush........................................................................................................................................................ 36
8.4.2 Side bristle skirts and rubber edge plate.................................................................................................. 36
8.5 Lubrication .............................................................................................................................................................. 37
9. WARRANTY TERMS..............................................................................................................................38

4 (40)
1. Foreword
Avant Tecno Oy would like to thank you for your purchase of this attachment for your Avant loader. It has
been designed and manufactured based on years of experience on product development and manufacturing.
By familiarising yourself with this manual and following the instructions, you ascertain your safety and ensure
the reliable operation and long service life of the equipment. Read the instructions carefully before starting to
use the equipment or performing maintenance.
The purpose of this manual is to help you to:
operate the equipment in a safe and efficient manner
observe and prevent any hazardous situations
keep the equipment intact and ensure a long service life
With these instructions, even an inexperienced user can use the attachment and loader safely. The manual
includes important instructions for experienced AVANT operators as well. Ensure that all persons using the
loader have received proper guidance and familiarised themselves with the manual of the loader, each
attachment that are used, and all safety instructions before using the equipment. Using the equipment for
other purposes or use in any other way than described in this manual is prohibited. Keep this manual at hand
throughout the service life of the equipment. If you sell or transfer the equipment, be sure to hand over this
manual to the new owner. If the manual is lost or damaged, you can request a new one from your Avant
dealer or from the manufacturer.
In addition to the safety instructions included in this manual, you must observe all occupational safety
regulations, local laws, and other regulations concerning the use of the equipment. Particularly the regulations
concerning the use of the equipment on public road areas must be observed. Contact your Avant dealer for
more information about local requirements before you operate the loader on road areas.
Contact your local AVANT dealer for any questions, service, spare parts or about any problems that may
occur with the operation of your machine.
This manual contains the original instructions in English. Due to continuous product development some of the
details shown in this manual may differ from your equipment. Pictures may also depict optional equipment or
features that are not currently available. We reserve the right to change the contents of the manual without
notification. Copyright © 2018 Avant Tecno Oy. All rights reserved.

5 (40)
.
Warning symbols used in this manual
The following warning symbols are used throughout this manual. They indicate factors that must be taken into
account to reduce the risk of personal injury or damage to property:
WARNING: SAFETY ALERT SYMBOL
This symbol means: “Warning, be alert! Your safety is involved!”
Carefully read the message that follows, it warns of an immediate hazard
that could cause serious personal injury.
The safety alert symbol by itself and with related safety statement
indicates important safety messages throughout this Manual. It is used to
draw attention to instructions involving your personal safety or the safety
of others. When you see this symbol, be alert, your safety is involved,
carefully read the message that follows, and inform other operators.
DANGER:
This signal word indicates a hazardous situation which, if not avoided, will cause
death or serious injury.
WARNING:
This signal word indicates a potentially hazardous situation which, if not avoided,
could cause serious injury or death.
CAUTION:
This signal word is used when minor injury could result if the instructions are not
followed properly.
This signal word indic
ates information about the correct operation and maintenance
of the equipment.
Failure to observe the instructions accompanying the symbol can lead to equipment
breakdown or other property damage.

6 (40)
2. Designed purpose of use
The AVANT Collecting broom 1100 is an attachment that is designed and manufactured to be used with
AVANT multi-purpose loaders shown in Table 1. The collecting broom is intended for removing sand, sanding
gravel or other small trash from larger yards, streets, or other even and hard surfaces, and serves well also in
professional use. The powerful collector will remove small material from surfaces with a single pass, leaving
the surface completely clear. The collecting broom is not suitable for collecting larger trash, such as
disposable cups, boxes, or similar materials, where other broom types, such as the bucket broom, may be
more suitable.
The collecting broom is driven directly by a hydraulic motor. Also the collector box opening mechanism is
hydraulic and does not require any additional equipment on the loader to operate. With the side brush, the
cleaning of kerbs and operating near walls is easy. The side brush can be fitted on either side of the collecting
broom. To reduce dust formation during operation, a water spraying system is available as an option, which
includes nozzles for the side brush as well. The collecting broom is intended for outdoor use only and can be
used only as a collecting system from the driver’s seat of the loader, so that the collecting broom is firmly on
the ground supported by its own wheels.
This operator's manual also includes instructions regarding installation of additional components, involving
hydraulic assemblies. Safety instructions and safe working practices related to hydraulic assemblies must be
followed strictly. Installation work is intended only for persons with adequate training or experience about
hydraulic assemblies, and the system must be tested for safety before commissioning. Consult your nearest
Avant service point if necessary.
The collecting broom 1100 is not designed for any other use than specified and must not be used for any
other purposes than intended.
The attachment has been designed to require as little maintenance as possible. The operator can perform
regular maintenance tasks. All repair work can’t be performed by the operator, and demanding repair and
maintenance operations are to be left for professional maintenance. All maintenance work must be done using
proper safety equipment. Spare parts must be identical with original specifications, which can be ensured by
using only original spare parts. A separate spare parts catalogue may be available, consult your Avant dealer.
Familiarise yourself with the manual's instructions regarding service and maintenance. Please contact your
AVANT retailer if you have additional questions about the operation or maintenance of the equipment, or if
you require spare parts or maintenance services.
Table 1 - Collecting broom 1100 - Compatibility with Avant loaders
Avant
220 series 2
225
225LPG
313S
320S
419
420
423
523
520
R20
525LPG
R28
528
530
630
R35
635
640
745
750
755i
760i
e5
e6
A36883 •- •••(•) (•) (•)
A426229 •- •••(•) (•) (•)
A426231 •- •••(•) (•) (•)
The compatibility recommendations are based on the width of the loader, lifting capacity, and adequate
breakout force. Normally the width of the attachment should match roughly the width of the loader. When
using too wide attachment the actual breakout force (bucket tilting capacity) decreases and the overall
performance will decrease.
It is recommended to use the attachment only with loaders marked with •in Table 1. When using with models
marked with (•), full performance may not be achieved. Additional counterweights may also be required. For
compatibility with a model not shown in table, contact your Avant dealer.

7 (40)
3. Safety instructions for using the attachment
Please bear in mind that safety is the result of several factors. The loader-attachment combination is highly
powerful and improper or careless use or maintenance may cause serious personal injury or property
damage. Due to this, all operators must carefully familiarise themselves about correct use and the operator's
manuals of both the loader and the attachment before starting operation. Do not use the attachment if you
have not completely familiarised yourself with its operation and the related hazards.
DANGER
Misuse, careless use, or using an attachment that is in poor condition, may
cause risk of serious injuries.
Familiarise yourself with the controls of the loader,
correct coupling procedure, and the correct way to operate the attachment at a safe
area. S
tudy especially how to stop the equipment in a safe manner. Read all safety
precautions carefully.
Read all safety instructions carefully before handling the attachment
WARNING
When attaching an attachment to the loader, ensure that the locking pins of the
loader's quick attach plate are in the lower position and that they have locked
the attachment to the loader. Never lift or move an unlocked attachment.

The Collecting broom 1100 is designed to be used by one operator at a time. Do not
let others near the danger area of the equipment when it is in use.

Always transport the attachment as low as possible to keep the centre of gravity low,
and keep the telescopic boom retracted during driving.
Never leave the driver’s seat when the broom is running or when the auxiliary
hydraulics control lever of the loader is locked on and keep a safety distance of at
least two metres from activated broom. Keep hands and feet away from moving
parts.
Beware of entanglement and severing hazards and possible debris thrown by the
broom.
Lower the attachment firmly on the ground before leaving the driver’s seat. Make
sure that the attachment is properly supported during any maintenance or
inspections. Do not leave the driver’s seat when the loader boom is lifted. Going
under a raised attachment or loader boom is dangerous, as the boom may lower due
to loss of stability, mechanical fault or when other person operates the controls of the
loader.
Beware of the crushing hazard of the moving broom shaft, always lower the broom
completely, or use appropriate supports, if it is necessary to handle the broom while
lifted.
Be sure not to tilt the attachment too far up to prevent the broom from tilting over the
tipping point of the hinged quick attach plate.
Keep in mind that the broom may throw material or objects at high speed. Do not
operate the equipment, if the broom cover is not in place.
Shut down the loader and place the attachment to a safe position as shown in Safe
stopping procedure before any cleaning, maintenance, or adjustments.
Pay attention to the surroundings and any other persons and machines moving in the
vicinity. Pay attention to the contours of the terrain and other hazards, such as
branches and trees that can reach to the driver's area,
loose rocks, and slippery
surfaces.

8 (40)
WARNING
Make sure to use only an attachment that is in good condition. Check the attachment
thoroughly in regular intervals. Do not modify the attachment in a manner that would
affect its safety. It is prohibited to drill ho
les on the attachment, and welding or other
means of fixing hooks or other objects on the attachment is strictly prohibited.
Use the attachment only for its intended purpose. Other use may create unnecessary
safety risks, and the equipment may get damaged.
Make sure that the loader is equipped with necessary safety components, and that
they are in working condition. Seat belt must be used. If there are specific hazards
related to the operating area, use appropriate safety equipment.
Also read the safety instructions and correct use of the loader from the operator's
manual of the loader.
WARNING
Hazard of thrown objects - Keep bystanders away.
Note
that the attachment can throw stones, gravel, or other objects
found in the area at high speed. A
lways keep a safety
distance of at least 2 metres to other persons.
WARNING
Risk of tipping over - Avoid overload.
Loader can tip over
when handling too heavy loads, or because of dynamic
movements caused by driving with and handling of a heavy
l
oad. Do not extend the telescopic boom when the load
approaches the lifting capacity of the loader, or when the
loader boom is in horizontal position. When you notice that
the rear wheels of the loader are about to lift from the ground,
or if the load indicator of the loader (if fitted) signals:
Lower the load calmly and retract the telescopic boom
Avoid sudden changes in speed or direction whenever load is lifted
Use additional counterweights as needed
. ..
WARNING
Entanglement hazard - do not use loose clothing during operation.
Never wear
loose clothing, long scarves, jewellery, or other items that might become entangled with
rotating parts while operating the attachment. If needed, wear a hat to prevent long hair
from coming into contact with the rotating parts.

9 (40)
WARNING
Risk of crushing -
Never allow anyone to get under a
lifted attachment or loader boom.
Keep in mind that the
loader boom can be lowered or tilted even if the engine has
been shut down (crushing hazard). The loader is n
ot intended
to be left to keep a load elevated for longer periods. Always
lower the attachment to a safe position before leaving the
driver's seat.
. ..
Safe stopping of the attachment, before going near the attachment:
WARNING
Always stop the a
ttachment following safe stopping procedure before leaving
the driver's seat.
Safe stopping procedure prevents all unintentional movements of
the attachment. Note that the loader boom can move down even if the engine of the
loader is turned off. Safe stopping procedure:
Lower the boom and the attachment on the ground.
Shut down the loader engine and lock the parking brake.

Release residual pressure from the hydraulic system; move all hydraulic control
levers to their extreme positions a couple of times.
Prevent starting of the machine, remove ignition key.
. ..
3.1 Personal protective equipment
Remember to wear proper personal protective equipment:

The noise level at the driver's seat may exceed 85 dB(A) depending on loader
model and operating cycle. Ex
tended exposure to loud noise can cause
hearing impairment. Wear hearing protection while working with the loader.
Wear protective gloves.
Wear safety boots whenever working with the loader.
Wear safety glasses when handling hydraulic components.

10 (40)
4. Technical specifications
Table 2 – Collecting broom 1100 - Technical specifications
Product number A36883 A426229 A426231
Working width: 1100 mm 1350 mm 1350 mm
Total weight: 1374 mm 1577 mm 1577 mm
Side brush available Option
A35698 Standard Standard
Water spraying system: Option
A37431
Option
A37431 Standard
Weight, without water spraying system
and side brush: 315 kg 315 kg 315 kg
Weight, with side brush: 340 kg 340 kg 340 kg
Water spraying system: 60 l, empty weight 30 kg
Collector box: 80 l, hydraulic opening
Brush type: 500 mm, 33 individually replaceable nylon brush discs
side brush: diameter 350 mm, nylon & steel
Recommended hydraulic flow: 28 l/min
Maximum input of hydraulic energy: 35 l/min,
22,5 MPa (225 bar)
Compatible AVANT loaders: See Table 1, Designed purpose of use

11 (40)
.
4.1 Safety labels and main components of the attachment
Listed below are the labels and markings on the attachment. They must be visible and readable on the
equipment. Replace any unclear or missing label. New labels are available via your retailer or contact
information provided on the cover.
. ..
WARNING
Make sure all warning decals are readable.
The warning labels contain important
safety information and they help to identify and remember the hazards
related to the
equipment. Replace damaged or missing warning labels with new ones.
. ..
Attachment identification plate
A46771 A46772 A46799 A46803
. ..
To apply a new label: Clean the surface thoroughly to remove all grease. Allow it to dry completely. Peel off
the protective film of the label and press firmly to apply. Take care not to touch the glue of the label.

12 (40)
.
Table 3 - Decal locations and warning messages
Decal Warning message
1 A46771 Read instructions before use.
2 A46772 Do not go under a raised attachment
or loader boom; stay away from raised
equipment.
3 A46803 Crushing hazard, floating attachment
bracket and side turning. Keep clear
of moving components.
4 A46799 Beware of thrown objects; keep a safe
distance from the equipment. (2 m), 2
pcs.
5 A423101 Identification plate
. ..
Table 4 - Collecting broom 1100 - Main components
1 Frame, including collecting box
2 OptiFloat quick attach plate mechanism
3 Support wheel, 3 pcs
4 Support wheel adjustment on each wheel
5 Side cover plate on both sides
6 Side brush (Optional extra)
7 Hydraulic valve and safety valve
8 Broom protective cover
9 Collector box hatch
10 Main broom
11 Side bristle skirt
12 Rear bristle skirt
13 Water tank (Optional extra)

13 (40)
5. Attaching the attachment
Attaching the attachment to the loader is quick and easy, but it must be done carefully. The attachment is
mounted to the loader boom by using the quick attach plate on the loader boom and the counterpart on the
attachment.
If the attachment is not locked to the loader, it may detach from the loader and cause a hazardous situation.
The loader must not be driven and the boom must never be lifted when the attachment has not been locked.
To prevent hazardous situations, always follow the coupling procedure shown below. Also remember the
safety instructions shown in this manual. The attachment is mounted to the loader as follows:
WARNING
Crushing risk - Make sure that an unlocked attachment will not move or fall over.
Do not stay in the area between the attachment and the loader. Mount the attachment
only on level surface.
Never move or lift an attachment that has not been locked.
Avant quick coupling system:
Step 1:
Lift the quick attach plate locking
pins up and turn them backwards into the slot
so that they are locked in the upper position.

If your loader is equipped with a hydraulic attachment locking system, see
additional instructions about the use of the locking system from the relevant
manuals.
E
nsure that the hydraulic hoses and the electric harness are not in the way
during installation.
Step 2:
Turn the quick attach plate hydraulically to an obliquely forward position.
Drive the loader onto the attachment. If your loader is equipped with a
telescopic boom, you can utilise this.

Align the upper pins of the loader’s quick coupling plate so that they are under
the corresponding brackets of the attachment.
Step 3:
Lift the boom slightly – pull the boom control lever backward to raise the
attachment off the ground.

Turn the boom control lever left to turn the bottom section of the quick attach
plate onto the attachment.
Lock the locking pins manually or lock the hydraulic locking.
Always check the locking of both locking pins.

14 (40)
WARNING
Risk of crushing - Avoid tipping over the attachment.
Excessive tilting or lifting of an unlocked attachment increases the risk of tipping the
attachment over. Do not use the automatic locking of the locking pins when the
attachment is lifted more than
one meter from the ground. If the locking pins do not
return to the normal position when tilting, do not tilt or raise the attachment any more.
Lower the attachment on the ground and secure the locking manually.
WARNING
Risk of falling objects - Pre
vent dropping of
attachment.
An attachment that has not been completely locked to the
loader may fall on the boom or towards the operator, or
fall under the loader during driving, causing loss of
control of the loader. Never move or lift an attachment
that
has not been locked. Before moving or lifting the
attachment, make sure that the locking pins are in the
lower position and come through the fasteners on the
attachment on both sides.
WARNING
Make sure the loader is compatible with the attachment.
Stability of the loader,
possible overload of the attachment, and compatibility of loader control systems must be
ensured in addition to mechanical compatibility of the attachment. If you use the
attachment with a loader that is not fit to be used
with the attachment model you have,
risks include tipping over, damage to attachment due to overload, and risks related to
uncontrolled motion of attachment and its parts. If your loader is not listed in Table 1 on
page 6, ask your Avant dealer before using this attachment.
5.1 Connecting and disconnecting hydraulic hoses
On Avant loaders the hydraulic hoses are connected using the multi connector system. If you have an Avant
300-700 series loader with the conventional quick couplers and wish to change to the multi connector system,
contact your Avant dealer or service point for instructions or installation services.
WARNING
Risk of movement of the attachment and ejection of hydraulic oil -
Never connect
or disconnect quick coupli
ngs or other hydraulic components while the control
lever of the auxiliary hydraulics control lever is locked on or if the system is
pressurized.
Connecting or disconnecting the hydraulic couplings while the system is
pressurized may lead to unintended movements of the attachment, or ejection of high-
pressure fluid, which can cause serious injuries or burns. Follow safe stopping procedure
before disconnecting hydraulics.

15 (40)
Keep all fittings as clean as possible; use the protective caps on both the attachment and
the loader. Dirt, ice, etc. may make using the fittings significantly more difficult. Never
leave the hoses hanging on the ground; place the couplings onto the holder on the
attachment.
Connecting the multi connector system:
1.
Align the pins of the attachment connector with corresponding
holes of the loader connector. The multi connector will not
connect if the attachment connector is upside down.
2.
Connect and lock the multi connector by turning the lever towards
the loader.
The lever should move easily all the way to its locking position. If the lever does not slide smoothly, check the
alignment and position of the connector and clean the connectors. Also shut down the loader and release the
residual hydraulic pressure.
To disconnect the multi connector system:
Before disconnecting put the attachment down on a solid and even
surface.
1. Switch off the auxiliary hydraulics of the loader.
2.
While pushing unlock button, turn the lever to disconnect the
connector.
3. After ending operation put the
multi connector on its holder on the
attachment.
Disconnecting hydraulic hoses:
Before disconnecting the fittings, lower the attachment to safe position on solid and level surface. Turn the
control lever of the auxiliary hydraulics to its neutral position.
When uncoupling the attachment, always disconnect the hydraulic couplings before
unlocking the quick attach plate, to prevent hose damage and any oil spills. Reinstall the
protective caps on the fittings to prevent impurities from entering the hydraulic system.
Releasing residual hydraulic pressure:
In case residual pressure is left in the hydraulic system of the attachment, it is often possible to disconnect the
hydraulic couplings, but it may be difficult to connect them the next time. If the fittings will not connect, the
residual pressure must be released by turning the auxiliary hydraulics control lever of the loader, when the
engine is turned off. To make sure that there will not be residual pressure in the hydraulic system of the
attachment, shut down the loader engine and move the auxiliary hydraulics control lever of the loader back
and forth before disconnecting the couplings.

16 (40)
.
5.2 Electric connection
Electric functions of the attachment:
The pump of the optional Water spraying system is electric. The electric water pump of the Water spraying
system can be controlled with the standard electric harness that is supplied with the attachment, or with the
Attachment control switch pack of the loader.
5.2.1 To connect the electric harness of the attachment to the loader
Starting form year 2016, there is an integrated electric plug in the multiconnector of the attachment. However,
a separate electric harness is also supplied with the attachment, to make it possible to connect and use the
attachment with loaders that are not equipped with Attachment control switch pack.
There are three ways to connect the electric connector, depending on the equipment on the loader and the
attachment:
1. If your loader is not equipped with the
attachment control switch pack:
Use the separate cable kit with a switch that is
supplied with the attachment. Connect this cable to
the 12 V electric socket near the operator's seat of
the loader, and to the electric plug of the
attachment.
1. Electric plug, connects to the 12 V elec
tric
socket near the operator's seat of the loader.
More information about the power outlet of
the loader can be found in the operator’s
manual of the loader.
2. ON-OFF switch
Select the location of the switch in the cab so
that it is easily accessible but wi
ll not be used
inadvertently.
This cable with a switch can be used only to
control the rotation of the chute.
3.
Connect to the electric plug of the
attachment.
If the attachment is equipped with a electric
plug that is integrated to the multiconnector
of the
attachment, disconnect the electric
cable from the multiconnector.
Cable harness A34731

17 (40)
2. If your loader is

equipped with the attachment control switch
pack, and
the loader is manufactured after 2016:
If the loader is equipped with the attachment
control switch pack, and the the electric socket
integrated in the multiconnector, the electric
harness of the attachment is connected when the
multiconnector is coupled. Clean both
multiconnectors before connecting the
multiconnector.
The separate cable
harness A34731 is not needed
when the loader is equipped with the Attachment
control switch pack.
Attachment control switch pack, loader
manufactured in 2016 or later
3. If your loader is

equipped with the attachment control switch
pack, and
the loader is manufactured before 2016:
If the loader is equipped with the attachment
control switch pack, and there is an electric socket
near the multiconnector of the loader, connect the
electric plug of the attachment to the socket of the
loader.
The s
eparate cable harness A34731 is not needed
when the loader is equipped with the Attachment
control switch pack.
Attachment control switch pack, loader
manufactured in 2015 or before
. ..
Make sure that electric cables will not get stuck, squeezed, or stretched when the
equipment moves.
With the help of the attachment control switch pack available for the loader, the
attachment control switches are easily accessible at the end of the boom control lever.
More information about the power outlet of
the loader can be found in the operator’s
manual of the loader.

18 (40)
.
6. Using the broom
Check the attachment and the operating environment once more before starting to work, and that all obstacles
have been removed from the operating area. Quick inspection of the equipment and the operating area before
use are parts of ensuring safety and the best performance of the equipment. Practise the use of the
attachment and its controls in an open and safe area. If you are unfamiliar with the loader in use, it is
recommended to practise its use without any attachments.
WARNING
Entanglement hazard -
Never leave the driver’s seat
when the broom is in operation
. Keep a safe distance
between the broom and other persons and stop the broom
and lower it down completel
y whenever others are in
proximity with the broom. Never perform any maintenance or
adjustments if the broom can start by accident. Shut down
the loader engine, turn off auxiliary hydraulics and lower the
loader boom before going near the attachment.
WARNING
Hazard of thrown objects - Keep bystanders away.
Note
that the attachment can throw stones, gravel, or other objects
found in the area at high speed. Always keep a safety
distance of at least 2 metres to other persons.
WARNING
Risk of tipping over - Avoid overload.
Loader can tip over
when handling too heavy loads, or because of dynamic
movements caused by driving with and handling of a heavy
load. Do not extend the telescopic boom when the load
approaches the lifting capacity of the
loader, or when the
loader boom is in horizontal position. When you notice that
the rear wheels of the loader are about to lift from the ground,
or if the load indicator of the loader (if fitted) signals:
Lower the load calmly and retract the telescopic boom
Avoid sudden changes in speed or direction whenever load is lifted
Use additional counterweights as needed

19 (40)
.
6.1 Checks before use
Before starting work, remove large items that can’t be collected with the broom from the working area.
Drive carefully on uneven terrain and note the effect of heavy load at the front of the loader to the
stability and handling of the loader.
Before each use, check the operation of the broom and ensure that the brush can rotate freely. Check
that there is no string or other foreign material coiled around the broom. Check also the condition and
the setting of the side brush.
Ensure that bystanders are at a safe distance when operating the equipment. Do not let anyone to
enter danger area of the boom or to stay directly in front of the loader. Also make sure that it is safe to
reverse with the loader. Never assume that bystanders will remain where you last saw them;
especially children are often attracted to the moving equipment.
Check the general condition of the attachment and the loader, and check for possible hydraulic oil
leaks. The attachment must not be used, if there is a fault in the hydraulic system of the loader or the
attachment. Refer to Chapter 7 for maintenance instructions.
Operate the attachment and the controls of the loader only when seated on the driver’s seat. Ensure
that the loader and the attachment are used in a safe manner and as intended. Do not allow children
to operate the equipment.
Never operate the loader or attachments while under the influence of alcohol, drugs, medication that
may impair judgement or cause drowsiness, or if not otherwise medically fit to operate the equipment.
Remember correct working methods and avoid leaving the driver’s seat unnecessarily.
Regularly clean the loader oil cooler core; refer to the operator's manual of the loader for
more instructions. Overheating oil decreases the power and affects the service life of the
hydraulic components of both the attachment and the loader.
6.2 Operator qualification
Anyone who intends to use the collecting broom must:
Know the intended use of the attachment.
Know how to use the loader safely in different operating conditions.
Read and always follow the instructions concerning the use of the attachment in this operator's
manual.
Have this manual and the operator's manual of the loader available.
Ensure that the loader and the attachment are used in a safe manner and as intended.
Never allow children to operate the equipment.
Never operate the loader or attachments while under the influence of alcohol, drugs, medication that
may impair judgement or cause drowsiness, or if not otherwise medically fit to operate the equipment.
Complete any possible mandatory training required by the employer before use.

20 (40)
.
6.3 Operating the broom
The broom is operated with the auxiliary hydraulics of the loader. The broom has two operating modes:
Auxiliary hydraulics control
lever:
(or electric joystick buttons):
Broom on its support
wheels:
Broom lifted off the
ground:
Broom rotate Close collector box
- Open collector box
Check the position of the storage supports before using the attachment. See instructions
in this manual.