Axel MC726 Series User manual

AXE 6 Digit Microprocess Counter (72x72mm) MC726 Series
■Features
◎Accept more type sensors(switch,encoder,proximity.etc) ◎Quadrature sensing up to 4 times resolution
◎Accept input rates up to 10KHz ◎Alarm output can programmable per-warn mode
◎Readout range from -199999~999999 ◎N,R,C alarm control mode
◎Four counting modes Up,Down,Up/Down,Quadrature ◎Alarm output action times 0.1~99.9 sec. Can be modified
◎Power down saving ◎0.36”highlight display
◎Decimal point can be modified ◎Man-machine interface,easy to operate
◎Input scaling multiplied 0.00001~9.99999 can be modified ◎EEPROM Saving,data safekeeping about 10 years
◎Reset by panel or connect terminal ◎Modified inside parameter,must have pass code
■Name of parts
■Connect diagram
◎Contact input(PNP) ◎CMOS input(12V or 15V) ◎Sensor input(PNP 12V)
◎Contact input(NPN) ◎TTL input(5V) ◎Sensor input(NPN 12V)
■Alarm output control mode description
◎N(MANUAL): When count value equal setting value the relay ON & continue coun
t until reset by panel or connect terminal
then relay OFF & count value return to RST setting value
◎
R(RETURN): When count value equal setting value the relay ON & continue count until relay action time out then relay
OFF & count value return to RST setting value
◎C(CONTINUE): When count value equal setting value the relay ON & count value return to RST setting value then continue
count & relay action time out the relay OFF
◎N/R/C control mode is according to AL1 setting value
◎WARN: When count to [AL1 value(digit 1~4) -warn value(digit 5~6)]RELAY 2 ON , count to AL1 value RELAY 1 ON
COM
IN
12V Inside jumper
1234
OFF
ON
ON
OFF
COM
IN
12V Inside jumper
1234
OFF
ON
OFF
OFF
COM
IN
12V Inside jumper
1234
OFF
ON
OFF
OFF
COM
IN
12V Inside jumper
1234
ON
OFF
OFF
OFF
COM
IN
12V Inside jumper
1234
OFF
ON
OFF
ON
COM
IN
12V Inside jumper
1234
ON
OFF
ON
OFF
GND
GND
Sensor
Sensor
126543
RST
ENT
AL
SEL
OUT1 OUT2 OUT3
AL1
AL2
PV
SV
Count value display
Setting value display
Per digit setting keys
Function keys

Key introduce Operation Manual
Key Function 1.In normal display,The key function is call out setting page
2.In parameter setting page,The key function is data Enter , and goto next page
RSTKey Function 1.The key function is count value retuen to RST value & relay OFF
AL SEL Key Function 1.In normal display,The key function is change alarm value & alarm indicate display
Per digit /Key
Function 1.In normal display,according to alarm indicate press per digit /key setting per alarm value 2.Into parameter setting page,If need modify data can press per digit /key into setting
procedure ,The parameter data will increment /decrement. (Key Response about 0.2 sec)
Digit 1 &Key
Function In setting page press digit 1 &key return normal display,
but if in setting page the modify data
will be lost
No Key in anything In setting page no key in anything about 2 minutes,return normal display,but if in setting page the
modify data will be lost
Step Parameter Mark Description Parameter Mark Operation Manual
1Normal display
Press /FUNC key into P.COD setting page
2P.COD(Pass code input page)
1.Key in 6 digit pass code with per digit or key
2.Press key,the pass code is right into setting page , otherwise
return normal display
3TYPE(Input Type setting
page) Default=1U2D
1.Decide input type with digit 1 or key (1U2D/1P2D/1A2B)
2.Press key enter data and into WARN setting page
4WARN(Pre-Warn)
Default = NO
1.Decide pre-warn mode with digit 1 or key(NO,YES)
2.Press key enter data and into RST setting page
5RST(Reset Value)
Default=0
1.Decide reset value with per digit &key(-199999~999999)
2.Press key enter data and into DP setting page
6DP(Decimal Point)
Default=0
1.Decide decimal point with digit 1 &key(0~5)
2.Press key enter data and into SCALE setting page
7SCALE(Display Scale)
Default=1
1.Decide display scale with per digit &key(0.00001~9.99999)
2.Press key enter data and into OP.MODE setting page
8OP.MODE(Output Mode)
Default=N
1.Decide output mode with digit 1 &key(N,R,C)
2.Press key enter data and into ACT.T setting page
9ACT.T(Active Time )
Default=0.1
1.Decide active time with digit 1~3 &key(0.1~99.9 sec.)
2.Press key enter data and into CODE setting page
10 CODE(Pass Code)
Default=0
1.Decide pass code with per digit &key(0~999999)
2.Press key enter data and into LOCK setting page
11 LOCK(Panel Lock)
Default=NO
1.Decide panel lock with digit 1 &key(NO,YES)
2.Press key enter data and return TYPE setting page
Step Parameter Mark Description Parameter Mark Operation Manual
1Setting alarm 1 value
Default=0
1.Press AL/SEL key,until AL1 indicate is light
2.Decide alarm 1 value with per digit &key(-199999~999999)
,no key in any key 5 sec. Auto save data
2Setting alarm 2 value
Default=0
1.Press AL/SEL key,until AL2 indicate is light
2.Decide alarm 2 value with per digit &key(-199999~999999)
,no key in any key 5 sec. Auto save data