Axess X Wireless Series User manual

Installation Manual

X-Series aXess 700-560-01E
Thank You For Choosing IDS to Protect You
Congratulations on your purchase of an IDS X-series alarm panel with aXess integration. IDS X-series panels are
powerful, versatile and highly configurable security systems, which should be installed by a professionally trained
installer.
This aXess Installation manual covers the aXess installation information and is not a complete X-Series guide. The
majority of panel features are programmable only by an IDS-accredited installer in possession of the INSTALLER CODE.
For information on programming the X-Series Alarm panel please refer to the appropriate manual. All user manuals can
be downloaded from www.idsprotect.com. Installer manuals can be downloaded if you are registered with IDS as a
company and have created an account on the website.
Features
Controls up to 8 doors
Arm/Disarm the X-Series alarm via an access control tag (Hold tag for 3 seconds on the reader)
Deny access if the alarm is armed
Forced door alarm
Fire doors
Access areas even if disconnected from the X-Series alarm panel
Readers can be configured to be Arm/Disarm only, Access Only or both
Transactions can be viewed from the keypad
Introduction
aXess is the perfect way to extend the functionality of an alarm panel by including access control for up to eight
doors. Each door has an interface that can be installed in two configurations:
1. Two readers: one on each side of the door for entry and exit.
2. One reader: one for entry and a push button for exit.
Access tags can be linked to alarm codes to be able to arm and disarm the alarm.
Clear Interface Memory
When powering up for the first time and the aXess readers do not show the correct LEDs short the “RESET” jumper (see
fig 3) for three seconds.
Installer Mode
Note: Only LCD keypads can be used to program aXess locations
Location 259 has been set aside for access control configuration.
Enter ‘Installer Mode’ and location
[9][9][9][9][*]
Enter location [2][5][9][*]
Enrolling Doors
This sub location is to identify each door to the alarm system and allocate each door with a number.
Use the scroll button to scroll to “Enrol Door”.
Enter [door number][*]
Swipe card (Any card, learnt or not, to identify the physical reader to the system)
Remove Door
Use the scroll button to scroll to “Remove Door”.
Enter [door number] [*]
Door Configuration
This sub location is to allocate each door to a partition, to set the lock strike time in milliseconds, and to set a zone
number if the door is to be monitored for forced/propped door and will operate as a normal alarm zone on the panel.
Use the scroll button to scroll to “Config Door”
Enter [door number][*]
Enter [partition number][*]
Enter strike time in milliseconds [ms] [*]
Enter [zone number] [*] - this is optional. If used, 'Door Switch enabled' must be 'Y' in the Advanced Door
Configuration.

X-Series aXess 700-560-01E
Advanced Door Configuration
Use “Advanced configuration”to enable or disable certain permissions, access types, and door settings.
Use the scroll button to scroll to “Config Door Adv”
Enter [door number][*]
Select the door’s options shown in the table below by scrolling and pressing [*] to enable ‘Y’ or disable ‘N’
Table 1: Door Configuration
Opt
Description
Default
1
Door Switch enabled
N
2
Silence the reader
N
3
Deny entry if armed
N
4
Enable as an Arm reader to arm/disarm the alarm
N
5
Enable as an Access reader
Y
6
Fire door
Y
7
Allow access if interface is disconnected from the system
N
8
Enable/Disable Door left Open Beep
Y
9
Enable/Disable forced door monitoring
Y
Door Switch Enabled –Enable this setting if a door contact is installed and you want to allocate a zone to the door to
monitor the door for forced open or held open situations.
Deny Entry if Armed –When enabled this option will disable the system from allowing anybody access through the
door if the door is allocated to the armed partition.
Arm/Disarm Reader –When enabled this option allows a tag allocated to an arm/disarm user code to arm or
disarm the system, depending on the state of the alarm, by holding the tag for three seconds in front of the
reader.
Access Reader –When disabled the reader will not function as an access reader. If the reader is an arm/disarm reader
and access is disabled it will allow the alarm to be armed or disarmed.
Note: The tag must have been allocated a valid alarm user code (defined below). The user code properties will define
the mode or type of arming.
Fire Door –If a door is enabled as a fire door and a fire alarm is triggered all fire doors will automatically unlock
Off Line Mode –if the interface loses communication with the panel due to a break in the communications bus
line, it will continue to operate as an access reader, but arm / disarm functionality will be disabled, and arm
status will not be shown.
Door Left Open Beep –If the door is monitored by a door magnet (Door Switch must be enabled) and left open for 30
seconds the reader will beep for 15 seconds to draw attention to the door being open. Disable if this feature is not
required
Forced Door Monitoring –This feature will raise an alarm if the door is opened without presenting an authorised tag
first. Door contact must be enabled and configured.
Master User Menu
Enter “Master User” menu:
Hold down [*] until beep
Enter Master user code [1] [2] [3] [4] [*]
aXess control menus are:
oMenu 32 “Add/Edit Card” by typing in the tag number
oMenu 33 “Add/Edit Card” by Swiping the tag
oMenu 34 “ Delete Card”
oMenu 35 “Delete Card by swipe”
oMenu 36 “View Transactions”
Option 32: Adding Access Tags
Menu option 32 allows the adding of access tags to the system or the editing of existing tags. The procedure to add a
tag is to enter the tag’s number, allocate it to a user code and any of the eight doors where the tag may be presented.
Enter [3] [2] [*]
oEnter the [card number] [*]
oSelect the doors by entering the [door number] [*] to enable ‘Y’ and by entering the [door number] [*] to disable ‘-’

X-Series aXess 700-560-01E
Door Selection
Table 2: Door Selection
Door
1
2
3
4
5
6
7
8
Default
Y
-
-
-
-
-
-
-
oTo select a door number press the number on the keypad followed by [*]
oOnce all selections are made press [*] to exit door/arm selection
oEnter [user code] then [*]. (If no user code press [*]
Option 33: Adding Access Tag by swiping the tag
Menu option 33 allows the adding of access tags to the system or the editing of existing tags by swiping the tag. The
procedure to add a tag is to swipe the tag on a reader, allocate it to a user code and any of the eight doors the system is
monitoring.
Enter [3] [3] [*]
oEnter the [Door No] [*] that will be used to swipe the tag
oSwipe card, if card number is correct, [*]
oSelect the doors by entering the [door number] [*] to enable ‘Y’ and by entering the [door number] [*] to disable ‘-
’. See Table 2 Door selection
oOnce all selections are made press [*] to exit door/arm selection
oEnter [User Code] then [*]. (If no user code press [*])
Option 34: Deleting Access Tags
This menu option allows the user to remove a card from the reader
Enter [3][4][*]
oEnter the [card number][*] to delete the tag
Option 35: Delete Access Tags via Swipe
This menu option allows the user to remove a card from the reader if the card is available
Enter [3][5][*]
oEnter the door number that the action will be carried out
oSwipe the card to be deleted
Option 36: View Transactions
This menu option allows the master user to view the log of transactions for a specific door. The most recent transaction
logged will be the first event displayed. To view older transactions the back scroll button can be used and once you
have scrolled back the forward scroll button can be used to go forward to the most recent entry. The keypad will give
an error beep if there are no transactions or the last recorded one has been reached.
Enter [3][6][*]
oEnter the door [number] of the transactions you want to view followed by [*]
Reader Feedback
Each access reader has three different colour LEDs, Red, Yellow, Green and a buzzer to communicate feedback to users
of the system depending on the type of reader
Figure 1: aXess Reader LEDS
Red
Yellow
Green

X-Series aXess 700-560-01E
Arming Only Reader
Table 3: Arming Only Reader LEDs
Action
Description....
ARMING ONLY READER
Red
Yellow
Green
Beeper
Factory Reset
All 3 LED's flashing in sync
None
Enrol Mode
Flashing in sync with
Green LED
Flashing out of sync
with Red/Green LED's
Flashing in sync with
Red LED
Single beep when any tag swiped
Idle
Following Partition's
ARM LED
ON if comms to panel
is good.
Following Partition's
READY LED
None
Learn Tag
Mode
Following Partition's
ARM LED
ON if comms to panel
is good.
Flashing
Single beep when tag swiped
Door Forced
Following Partition's
ARM LED
ON if comms to panel
is good.
Following Partition's
READY LED
Failed Beep (if door switch
connected and configured)
Door Left Open
Following Partition's
ARM LED
ON if comms to panel
is good.
Following Partition's
READY LED
Door Left Open Beep (if door
switch connected and
configured)
Tag held in field
(Arming Time)
Following Partition's
ARM LED
Slow Flash
Following Partition's
READY LED
None
Access Only Reader
Table 4: Access Only Reader
Action
Description....
ACCESS ONLY READER
Red
Yellow
Green
Beeper
Factory Reset
All 3 LED's flashing in sync
None
Enrol Mode
Flashing in sync with
Green LED
Flashing out of sync
with Red/Green LED's
Flashing in sync with
Red LED
Single beep when any tag swiped
Idle
Following Partition's
ARM LED
ON if comms to panel
is good.
Following Relay
None
Learn Tag
Mode
Following Partition's
ARM LED
ON if comms to panel
is good.
Flashing
Single beep when tag swiped
Access Granted
(Relay On)
Following Partition's
ARM LED
ON if comms to panel
is good.
Following Relay (On
whilst Relay is On -
Strike Time)
Single beep when valid tag
swiped
Access Denied
Solid On for 2s
ON if comms to panel
is good.
Off
Failed Beep
Door Forced
Solid On for 2s
ON if comms to panel
is good.
Off
Failed Beep (if door switch
connected and configured)
Door Left Open
Following Partition's
ARM LED
ON if comms to panel
is good.
Off
Door Left Open Beep (if door
switch connected and
configured)
Tag held in field
(Arming Time)
Not Available

X-Series aXess 700-560-01E
Access & Arming Reader
Table 5: Access & Arming Reader
Action
Description....
ACCESS & ARMING READER
Red
Yellow
Green
Beeper
Factory Reset
All 3 LED's flashing in sync
None
Enrol Mode
Flashing in sync with
Green LED
Flashing out of sync
with Red/Green LED's
Flashing in sync
with Red LED
Single beep when any tag swiped
Idle
Following Partition's
ARM LED
ON if comms to panel
is good.
Following Relay
None
Learn Tag Mode
Following Partition's
ARM LED
ON if comms to panel
is good.
Flashing
Single beep when tag swiped
Access Granted
(Relay On)
Following Partition's
ARM LED
ON if comms to panel
is good.
Following Relay (On
whilst Relay is On -
Strike Time)
Single beep when valid tag swiped
Access Denied
Solid On for 2s
ON if comms to panel
is good.
Off
Failed Beep
Door Forced
Solid On for 2s
ON if comms to panel
is good.
Off
Failed Beep (if door switch
connected and configured) and X-
Series will go into alarm
Door Left Open
Following Partition's
ARM LED
ON if comms to panel
is good.
Off
Door Left Open Beep (if door
switch connected and configured)
Tag held in field
(Arming Time)
Following Partition's
ARM LED
Slow Flash
Following Relay
None
Diagrams
Figure 2: Interface Inputs Wiring Diagram

X-Series aXess 700-560-01E
Figure 3: Tag Reader Wiring Diagram
Figure 4: Jumpers
Reset Jumper
Clears all memory
Term Jumpers
Do not short
Mode Jumper
Used if Wiegand device
attached

X-Series aXess 700-560-01E