Aybey Elektronik ALYA User manual

APPENDIX-3 LANDING OPERATION PANEL INSTALLATION
ALYA
SERIAL COMMUNICATION DUPLEX LOP
INSTALLATION MANUAL
Document Name : Duplex ALYA User and Installation Manual
Display Type : Dot Matrix Led
Document Code : --
Document Version : 1.0

1
ALYA LOP Contents
•ALYA Serial Communication Duplex LOP
•Mounting Dowels and Screws
•User Manual and Installation Manual
•Terminating Resistor for systems without a shaft pit board with CAN interface.
1- Mechanical Installation
1.1 Open the front cover by pressing the spring mechanism at the bottom center of
the ALYA LOP with a screwdriver.
1.2 Mark the holes of screws and cable by placing the rear plate onto wall you want
to install.
1.3 Drill the holes (shown on Figure 2 by X) for M7 dowels.
1.4 Open a hole in the wall through which the rectangular socket of the panel with
sizes 50x50mm can pass (shown as E in Figure 2)
1.5 Insert the four dowels into the drilled holes (X).
1.6 Attach the backplate on the wall by using 4 M4x35 screws to complete
mechanical installation.
Figure 1
Figure 2

2
2- Electrical Connections
2.1 Connect the CANBUS cable terminals to the LOP interface in the control panels (100-
1000-CL1-CH1). The indicator of the side that is not connected to the control panel does
not light.
2.2 If your system includes a shaft pit control box with CAN interface as shown in Figure
3, then connect all LOPs with CANBUS cables with two white rectangular sockets.
2.3 If no electronic shaft pit boards with serial interface are present, then insert 2
terminating resistors into the lower sockets of the LOP at the bottom floor as shown
in Figure 4.
Figure 4
Figure 5

3
3- Operation and Adjustment Operations
There are 4 programming buttons on the board: UP, DOWN and ENT-R/L. You can
increase the value of a parameter by pressing UP and decrease it by pressing DOWN
button. The ENT-L button allows making changes to the left display, and the ENT-R
button to the right display. After setting it to the desired value, press ENT button shortly
to confirm.
Press the ENT button for 3 seconds to enter the setting menu of the right or left indicator,
whichever is to be adjusted.
You will see the floor number of the LOP (which is called as its ID) and the characters “ıd”
flashing sequentially. Here “ıd” represents the parameter name and the number is its
value. You can increase the floor number by pressing UP button and decrease it by pressing
DOWN button. Only the floor number is displayed while one is pressing UP or DOWN
buttons. When no button is being pressed then again “ıd” and floor number will be flashed
sequentially.
When you have adjusted all parameters then press the same ENT button 3 secs to save
the parameters and exit from menu.
Parameter
Code
Range
Definition
ıd
0…63
Floor Number of LOP
bL
0…9
Buzzer Level.
Increasing value makes the buzzer volume to decrease, where 1
is the loudest value.
Zero value disables buzzer.
SM
0,1
0-Lift Operation Mode
1-Simulation Mode where LOP stops communication and
displays numbers in the range of 0 to Simulation Floor.
SF
0…63
Maximum displayed Floor Number in simulation mode.

4
Parameter
Code
Range
Definition
SL
0,1
Slide Mode
0-Floor Number does not slide when floor changes.
1-Floor Number slides when floor changes.
Ar
1…5
Arrow Type
One of the five Arrow styles can be selected.
GM
0,1
Arrow-Character Location
0-Arrow is above, Floor Number below
1-Floor Number is above and Arrow is below.
DS
0,1
Door Select
0-A
1-B
ES
0,1
Energy Saving Mode. (Energy saving mode must be activated on
the control board in order to use this feature).
0-Passive
1-Active
ND
0,1,2
Next Direction
0-Arrow operates in normal mode.
1- Arrow operates in next direction mode.
2-Arrow is not available (In next direction mode)
4-Caution
4.1 Use only special stainless steel cleaners to clean the panels.
4.2 Do not use any detergent or acids to clean panels.
4.3 Avoid to contact any liquid to the LOP.
4.4 In case of an electrical failure, switched off the LOP and contact with Aybey
Elektronik Technical Service.