AZ Patio Heaters HLDS01-GTSS Parts list manual

Quartz Tube Patio Heater
Read these instructions before using this
appliance. The appliance must be installed in
accordance with the instructions and local
regulations. The use of this appliance in enclosed
areas can be dangerous and is PROHIBITED.
Do the leak test after each changing of LPG
cylinder.
Never check for leaks with a match or open flame.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this appliance.
•
•
•
•
Close the valve of the gas cylinder or regulator.
Extinguish all naked flames; do not operate any
electrical appliances.
Check for leaks as detailed in these instructions.
If odor persists, contact AZ Patio Heaters at
1-888-775-1330.
•
•
•
•
DO NOT RETURN THIS ITEM TO STORE WHERE PURCHASED. PLEASE CALL 1-888-775-1330 (ENGLISH ONLY)
WITH QUESTIONS OR WARRANTY ISSUES MONDAY TO FRIDAY 8:00 a.m. - 4:30 p.m. SATURDAY/SUNDAY
8:00 a.m - 2:00 p.m PST OR VISIT OUR WEBSITE WWW.AZPATIOHEATERS.COM.
3177588
5/22/2012 MADE IN CHINA

1-888-775-1330.
36 in /91.4cm and
sides 24 in /60.9 cm.
24 in/60.9cm
36 in /91.4cm

TWO SIDED BOLTS
WITH WING NUTS
Please call us at 1-888-775-1330 (English only) for missing parts.
STABILITY RING ATTACH TO BASE H1

Please call us at 1-888-775-1330 (English
only) for missing parts.
GG

STEP 5: Install 4 pieces of connected tube on
the top of the pre-assembled base(PART GG).
Screw the bolts at the bottom tightly.
(PART B 16PCS)
STEP 6: Open the flame screen carton, take out the flame
screen (PART AA) to the top of the aluminium tubes using
hardware provided (PART B 8PCS)
STEP 7:
Take out 3 two sided bolts (Part A) out of
screw pack, and connect to flame screen(Part AA). Attach
reflector(Part G) through the 3 bolts. Then tighten the
shield with the 3 wing nuts.
STEP 3: Mount the stabilty ring(PART H) to the
base of the heater.
STEP 8:Open the glass tube box and take out the glass tube
(PART EE). Squeeze the stainless steel ring together(PART DD),
and carefully slide the ring inside one end of the
glass tube( PART EE).
STEP 4: Open the aluminium tube carton, take out
all of the aluminium tubes (PART CC) Connect two
tubes together. Screw the bolts in the middle position
tightly using the hardware provided (PART B 8PCS).

STEP 8.2: Insert the assembled glass tubes into the heater
by holding the base in one hand, top in the other, and
insert the tube underneath the flame screen (PART AA).
STEP 8.3: After inserting one side into the flame
screen (PARTAA), place the lower end on the rubber
ring (PART DD) on top of the ceramic burner.
CAUTION
Make sure two glass tubes are tightly connected.
After assembling, the total length should be 49.5 in/125.7cm.
Avoid scratching the interior surfaces of tubes with the
stainless steel ring while joining the tubes.
STEP 8.4: Before inserting the assembled tube, please
make sure the tubes are fully connected. A bad
connection may cause damage to the glass tubes.
STEP 8.1: Slide the other side of stainless steel
ring (PART DD) into the second glass tube(PART EE)
by squeezing the stainless steel ring
together( PART DD).
5

1. Check and ensure a AA battery (included) is inside
the ignition chamber and has power. Ensure the anode(+)
faces outside.
2. Ensure the control knob is OFF,slowly open the gas
cylinder valve.
3. Press and turn the
control knob to PILOT
position and hold in for
1 full minutes.
4.Push the igniter to
generate spark while
keeping control knob
in depressed position.
5. Check for pilot
D
C
6
B-4PCS
STEP 9: Open the mesh guard carton, take out
mesh guard(Part BB). Hang the screens on the
four sides of aluminium tubes(Part U) and connect
top parts and bottom parts with small steel connector
tubes(Part E) from glass tube box.
Installation process
is complete.
Please remove protective
membrane off stainless
steel before you use.
OPERATION
10
11

7
DO NOT store in a location that will exceed120
degrees F/48.8 Celsius.

Any repairs to the patio heater must be carred out by a qualified person. For futher assistance, contact
AZ Patio Heaters at 1-888-775-1330 (English only).
MADE IN CHINA
ITM. / ART.639564
PH08-SSB / HLDS01-GTSS
Input rate: 40000BTU/HR
Gas: Propane
Gas supply pressure: 25 to 250PSI / 3.5-10.5Kg/cm²
Manifold pressure: 11"WC-2.74KPA
INJECTOR SIZE: 1.95mm-0.07 in
8
3177588
-11.7KW/HR
Distributed by
AZ Patio Heaters LLC
8550 N. 91st Ave
Suite C-25 Peoria, AZ 85345
1-888-775-1330
WWW.AZPATIOHEATERS.COM
W[email protected]