B9Creations Cure XL User manual

Instructions for Use

Dear Customer,
Thank you for choosing the B9 Model Cure XL.
A lot of research & developments have gone into the manufacturing of
this product. We sincerely hope that it will give you many years of trouble-
free use. Please read and understand all the instructions before using this
equipment.
Save these instructions for use for your reference.
The instructions for use are subject to change without further notice.
2828 Plant St., Ste. 2
Rapid City, SD 57702
[phone]
www.b9c.com
[email protected]

Table of Contents
1. Symbols Used 2
1.1 In these instructions for use 2
1.2 On the product / packaging 2
2. Safety Information 3
2.1 Installation and connection 3
2.2 Operation 4
2.3 Maintenance 5
3. Product Information 6
3.1 Indications for use 6
4. Package And Part Name 7
4.1 Main unit part name 7
4.2 Table of contents 7
5. Functions 8
5.1 Instruction for touch panel 8
5.2 IDT (Intensity Duty-Cycle Timer) setting 8
5.3 Basic operation 9
6. Troubleshooting 11
6.1 Instructions for fuse replacement 11
7. Maintenance And Cleaning 12
7.1 Cleaning inner chamber 12
7.2 Cleaning outer case 12
8. Product Specication 13
9. Warranty 14
10. Declaration Of Conformity 14
1

1. Symbols Used
Warning
Indicates a potentially hazardous situation that could result in serious injury
or death.
Caution
Indicates a potentially hazardous situation that may result in minor/moderate
injury or damage of property.
Hot SurfaceDanger Electricity
1.2 On the product / packaging
Serial number Catalogue number
Manufacturer Date of manufacture
Atmospheric
pressure for storage
Temperature limits
Storage humidity
range
CE marking Store in a dry place
95%
10%
106kPa
50kPa
10°C
40°C
1.1 In these instructions for use
Consult the
Instructions for use
2

Warning
2.1 Installation and connection
• Please install the product at least 5 cm away from the wall. In addtion,
do not place any objects above the product. Please keep the product
away from any heating appliances. Overheating the product may cause
re and/or electrocution.
• Do not block the ventilators on the left, right, and back side of the
product. Blockage may cause re and/or breakdown because of rises in
the inner temperature of the product.
• Keep the product at a location away from water.
• Keep the product at a location without excess humidity and temperature.
• Do not keep the product at a location for chemicals or a location where
gas is released.
• Do not keep the product at a sloping location. Do not shake or impact
the product.
• Use only AC100-240 V power-supply voltage. Using the wrong voltage
input may cause re and/or electrocution.
• Do not place heavy objects on the power cord. Damage to the cord may
cause re and/or electrocution.
• Do not disassemble this product. Unauthorized disassembly of this
product may cause electrocution and/or breakdown.
• Do not damage, bend, twist or pull the power cord. Doing so may cause
re and/or electrocution.
• Ensure earthing of terminal outlet and power socket. Electricity leak in
the main unit might cause electric shock and/or re.
• Pay attention to the frequency of the power supply/power voltage and
allowable current value (or consumed power.)
2. Safety Information
3

2.2 Operation
Warning
Caution
• Do not look inside the product during operation.
• Do not push the Start-Stop button while the door is opened.
• Do not operate the product when the door is opened, as it may cause
damage to your eyes.
• This product should be operated by qualied people only.
• If the product is in an unnormal state, such as emitting smoke and/or
making irregular noise, please switch off the power switch immediately.
Pull out the plug and contact the distributor.
• If water leaks inside the product, switch off the power switch
immediately. Pull out the plug and contact the distributor. Continuing to
operate this product may cause re and/ or electrocution.
• Never touch the power plug with wet hands to avoid electric shock.
• Never handle any liquid or metal power in the curing chamber to avoid
electric shock or re caused by internal circuit failure.
• Do not disassemble this product. Unauthorized disassembly of this
product may cause electrocution and/or breakdown.
4

2.3 Maintenance
Warning
• If this product is dropped, broken or damaged, switch off the power
switch. Then pull out the plug and contact the distributor. Continuing to
operate the product may cause re and/or electrocution.
• Be sure to pull out the plug when maintaining the product.
• When moving the product, please switch off the power switch and pull
out the plug.
• When pulling out the plug, do not pull out the power cord.
• When checking, wiping or replacing fuses, always turn off and unplug
the unit. Leave the unit off for at least 10 minutes to ensure that the unit
has cooled off completely.
Caution
• Remember to have regular inspections of the equipment and parts.
• If the product will not be used for a long time, please pull out the plug for
safety.
5

This product is a light curing machine for laboratory and professional use only.
3.1 Indications for use
• Save time
Fast-curing High-power LED, broadband LED, save fabricating time.
• Save money
Stable and high power LED with constant current circuit, avoid the cost and
hastle of replacing UV uorescent light tube.
• Multiple functions
Users can set up the curing details easily to gain process efficiencies by
Intensity Duty-Cycle Timer (IDT) settings.
• Post-curing for 3D printing
High-power Ultra Violet A (UVA) LEDs is included, which results in a quick
and uniform curing cycle.
3. Product Information
6

4. Package And Part Name
4.2 Components
Description
B9 Model Cure XL
Power cord
Instructions for use
Quantity
1
1
1
1Operation Panel
2Handle
3 Door
4Power Button
14
3
2
5 Cooling fan
6 Power Switch
7 Fuse
8 Outlet
6
5
7
USE ONLYWITH A 250V FUSE
8
4.1 Part name
7

5.1 Instruction for touch panel
5. Functions
1 432 5
5.2 IDT (Intensity Duty-Cycle Timer) settings
• Intensity Setting
Depending on the strength, thickness, and shape of the material, operator
can set the light intensity from Level 1(lowest) to Level 16(strongest). Intensity
range: 7018 –112295 mW/cm2when LED current at 43.8-700mA.
Suggestion: When curing flat and/or thin material, lower the intensity level
with longer timer to optimize the overall strength of the material.
Adjust the light intensity from Level 1 to Level 16.
Adjust the duty cycle (See chapter 5.2) from Level 1 to Level 10
(consistent brightness)
Adjust the working time between 5 seconds - 30 minutes.
Display: Indicate numerical value and remaining seconds.
+ : Increase the level of intensity, duty cycle and working time. Hold and
press the button to fast-forward.
- : Decrease the level of intensity, duty cycle and working time. Hold and
press the button to rewind.
: Start and stop curing
1
1
1
2
3
4
5
8

2. Press to power on.
3. Press to set up IDT.
4. Press START to cure.
5.3 Basic Operation
• Duty Cycle
Duty cycle is the ratio between pulse duration and the period (the picture
below shows the difference between each cycle). Depending on the
shrinking rate of the material, operator can set the duty cycle from level1
(10%) to level 10 (100%).
Suggestion: When curing small and/or thin material, lower the duty cycle
level to reduce the shrinkage and deformation rate.
• Curing Time
Set the time between 5 seconds – 9:55 minutes with 5-second intervals, and
set the time between 10 minutes – 30 minutes with 1-minute intervals.
1. Turn on the Power Switch.
9

Press to pause curing.
The button will start ashing when
paused.
Note, curing will be paused once the
door is opened. The button will start
ashing as well.
5.3.1 Pause curing during the operation
5.3.2 Increase/decrease curing time when pausing curing
Press + to increase or press − to decrease
curing time.
After adjusting the curing time, press
to restart.
5.3.3 Reset IDT when pausing curing
Press the buttons to reset IDT setting.
After resetting, press to restart it
1. Make sure the power is on
2. Press to set up the terms of curing.
3. Hold and press the button . After hearing 2 beeps, the system will
memorize the IDT setting and save it as the new default.
5.3.4 Memory mode
10

6. Troubleshooting
6.1 Instructions for fuse replacement
Use flat head screw
driver to unclench the
cover shown above.
1
4
32
5
Take the fuse out.
Take out spare fuse
at the bottom.
Change the fuse. Put the fuse
cover back.
Before replacing
the fuse, turn off the
power switch and pull
out the plug.
6
* Please replace the fuse if the panel indicator does not work. Be sure to pull the
power cord before replacement. After replacement, if there's still a problem with
the panel indicator, please contact customer service for repair.
USE ONLY WITH A250V FUSE
USE ONLY WITHA 250V FUSE
Trouble Possible Cause Measures
Time display does not light
up even if the power switch is
turned on.
Blowout of fuse. Replace with new fuse.
Contact our customer
service if the problem
persists.
LED does not light up even if
the is pressed.
Door is not
closed correctly.
Ensure the door is closed
properly.
Er1 Overheat Immediately turn off the
unit.
Contact our customer
service and mention
the error number on the
display.
11

7. Maintenance And Cleaning
• Remember to have regular inspections of the equipment and parts.
• In case of malfunction, do not attempt to repair the product by yourself.
Contact customer service for repair.
• Before maintenance, switch off the power swtich and pull out the plug.
7.1 Cleaning inner chamber
1- When the inner chamber gets dirty, clean it with soft cloth with alcohol or
cleaner.
2- If resin adheres to any part of the curing chamber, please remove it prior
to next curing.
7.2 Cleaning outer case
1- Do not use organic solvent including benzene and thinner to clean.
2- Gently wipe the unit with a soft cloth with alcohol or cleaner.
12

Type of Information Specications
Device name LED Light Curing Machine
Model name B9 Model Cure XL
Power input AC 100-240 V / 50-60 Hz
Power consumption 70 W
Fuse 2 A
Quantity of LEDs 25
Wavelength of LEDs 375~470 nm
Curing time 5 seconds - 30 minutes
Dimensions L200 x W220 x H160 mm (max)
Weight 3 Kg
Operating environment
Indoor use only.
Ambient temperature:
Relative humidity:
Atmospheric pressure:
Storage and transport
environment
Ambient temperature:
Relative humidity:
Atmospheric pressure:
8. Product Specication
75%
30%
1.0-atm
0.5-atm
10°C
40°C
50°F
104°F
106kPa
50kPa
95%
10%
1.0-atm
0.5-atm
10°C
40°C
50°F
104°F
106kPa
50kPa
13

9. Warranty
B9Creations, LLC. warrants the product to be free of manufacturing defects
for a period of one year from the date of purchase; this is deemed as the
date of the invoice. In the case the machine malfunctions under normal use,
contact B9Creations for the return process. Repairs must be only carried out by
B9Creations. If repairs or disassembly during warranty period are not carried out
by B9Creations, warranty will expire immediately. The following are expressly
excluded from the warranty:
1. Damage and/or failure of the equipment caused by falling and/or jolting
during transportation after purchase and/or during the normal use.
2. Damage and/or failure of the equipment caused by natural disasters, such
as earthquakes, oods, lightning, pollution, incorrect electrical voltage and
voltage spikes.
3. Any attempts to change or re-model the product will invalidate the warranty.
10. Declaration Of Conformity
Manufacture Made inTaiwan
Safety IEC / EN 61010-1 3rd : 2010
EMC EN 61326-1:2013
11. Document History
Edition Date Comments
A2020-05-21 Released
B2020-08-31 Update the "Power Switch"
icon
14