
11 12
ASSEMBLY MONTAJE ASSEMBLY MONTAJE
Copyright © 2022, Baby Trend Inc., All Rights Reserved. Todos los derechos reservados. Copyright © 2022, Baby Trend Inc., All Rights Reserved. Todos los derechos reservados.
FENDER
GUARDABARROS
To secure the fender to the frame, use the
4 screws provided.
Para sujetar el guardabarros al armazón, use los 4
tornillos provistos.
7) • Examine the boom of the front fender. You
will noce four 1/4 inch diameter plasc tubes
protruding from the boom (Fig. 7a).
• These tubes must be lined up with the holes in
the front frame assembly (Fig. 7b).
• Line up the front fender and press onto the
front frame assembly (Fig. 7c).
• Insert the 4 screws through the underside
of the front frame assembly into the front
fender's plasc tubes. Tighten the screws only
unl snug (Fig. 7d). DO NOT OVER TIGHTEN.
• Examine la parte inferior del guardabarros
delantero. Notará cuatro tubos pláscos de
¼ pulgada de diámetro que sobresalen de la
parte inferior (Fig. 7a).
• Estos tubos deben estar alineados con los
agujeros del armazón delantero (Fig. 7b).
•
Alinee el guardabarros delantero y presiónelo
en el armazón delantero (Fig. 7c).
• Introduzca los 4 tornillos por debajo del
armazón delantero en los tubos pláscos
del guardabarros delantero. Ajuste bien los
tornillos sin forzarlos (Fig. 7d). NO AJUSTE
DE MÁS.
Fig. 7a
Fig. 7b
Fig. 7c
Fig. 7d
REAR WHEEL
RUEDA TRASERA
8) • Lean the stroller forward to rest on the front
wheel. To aach the rear wheels, push each
wheel’s axle into the plasc corner ng as
shown in (Fig. 8). Depress the metal lever on
the inside of the corner ng as you push the
axle into corner ng. When the wheel will
not go on any farther, release the lever. Check
that the wheel has locked into the corner
ng by pulling on the wheel. If not locked, li
upward on the lever, push the wheel on farther
and release lever.
• Ensure that the wheels are rmly locked into
place. NEVER use the stroller if the wheels are
not locked into place, contact our customer
service department immediately at 1-800-
328-7363, between the hours of 8:00am and
4:30pm PST, for assistance.
• Incline el carrito hacia delante de modo que se
apoye en la rueda delantera. Para colocar las
ruedas traseras, empuje el eje de cada rueda
dentro del accesorio plásco de la esquina
como se indica en la Fig. 8. Baje la palanca
metálica que está dentro del accesorio de
la esquina mientras empuja el eje hacia el
interior del mismo. Cuando no pueda empujar
más la rueda, suelte la palanca. Tire de la
rueda para vericar que se haya trabado en el
accesorio de la esquina. Si no se trabó, levante
la palanca, empuje la rueda aún más y suelte
la palanca.
• Asegúrese de que las ruedas estén rmemente
trabadas. NUNCA use el carrito si las ruedas
no están bien trabadas, y llame a nuestro
departamento de servicio al cliente de
inmediato al 1-800-328-7363 en el horario
de 8:00 a.m. a 4:30 p.m., Hora Estándar del
Pacíco para recibir ayuda.
Fig. 8
Underside
Parte inferior