BaByliss PRO BAB2638U User manual

Model BAB2638U
Model BAB2639U
IONIC AIRSTYLER

IONIC AIRSTYLER
A powerful 800W styler that is designed to shape, smooth and add
volume as you dry. Instant ionic conditioning releases a stream of ions
that surround and condition each strand of hair to neutralise static,
smooth the outer layer of the hair cuticle and deliver a frizz-free, shiny
nish.
BAB2638U 34mm brush
BAB2639U 50mm brush
Features:
• Powerful 800W
• Fixed thermal brush with epoxy tips
• Ceramic coated barrel
• Instant ionic conditioning system
• 3 heat/speed settings, including a cool setting
• Safety cool tip
• Salon length 2.7m swivel cord
SAFETY CAUTIONS
• This appliance should only be used as described within
this instruction booklet. Please retain for reference.
WARNING! Polythene bags over a product may be
dangerous. To avoid danger of suffocation, keep this
wrapper away from babies and children. This bag is not a
toy.
• UK Only: This appliance must not be used in the
bathroom. If using the appliance in a bathroom, unplug
after use as the proximity of water can be dangerous even

if the appliance is switched off. For additional protection
the installation of a residual current device RCD) with a
rated residual operating current not exceeding 30mA is
advisable in the electrical circuit supplying the bathroom.
Ask your installer for advice.
WARNING! Do not use this appliance near water
contained in basins, bathtubs or other vessels.
• Do not use this appliance in the bathroom.
• Do not immerse the appliance into water or other liquids.
• Never look directly into the barrel of the hairdryer when it
is switched on.
• Always inspect the appliance before use for noticeable
signs of damage. Do not use if damaged, or if the
appliance has been dropped. In the event of damage,
contact the Conair Customer Care Line (refer to ‘UK After
Sales Service’ section for further information).
• Do not use the appliance if the lead is damaged. In the
event of damage, discontinue use immediately. Return
the appliance to the Conair Service Centre (refer to ‘UK
After Sales Service’ section for further information).
• Do not leave the appliance unattended when switched on or
plugged in.
• This appliance is equipped with a safety thermostat. In
the event of overheating, the appliance will run hot and
cold intermittently. In the event of this happening, turn
the dryer off, unplug from the mains and allow to cool
for 15 minutes. Before using again, ensure the rear lter
is clear of hair and other debris. Plug in and switch on.
If the appliance continues to overheat (i.e. element glows
red intermittently), discontinue use immediately, switch off
and unplug. Contact the Conair Customer Care Line (refer
to UK After Sales Service section for further information).
• Take care that the air vents do not become blocked when
in use. Ensure the rear lter is clear of hair and other

debris before use.
• Do not place the appliance on any surface whilst in
operation.
• Take care to avoid the hot surfaces of the appliance
coming into direct contact with the skin, in particular the
ears, eyes, face and neck.
• This appliance should not be used by adults whose
reduced physical, sensory or mental capabilities, or
whose lack of experience and knowledge, might cause
a hazard, unless they have been correctly instructed to
understand the safe use and hazards involved and are
adequately supervised.
• Careful adult supervision is required when this appliance
is used on or near children. Do not use on very young
children.
• This appliance should not be used, cleaned or maintained
by children. Keep out of the reach of children.
• Allow appliance to cool before storing away.
• After use, do not coil the lead around the appliance as
this may cause damage to the lead. Instead, coil the lead
loosely by the side of the appliance.
• This appliance complies with the requirements of Directives
2004/108/CEE (Electromagnetic Compatibility) and
2006/95/CE (Electrical Safety of Domestic Appliances).
amended by Directive 93/68/EEC (CE Marking).

IONIC TECHNOLOGY
Many aspects of modern living, including air conditioning, contact with
man-made bres and air pollution, even brushing and towel drying hair
contributes to a build-up of static charge in the hair leading to the
scales on the cuticles to push each other apart. As a result the surface
of the cuticle itself becomes rough and causes hair to appear dull and
is difcult to style.
Ionic technology emits a stream of Ions, which act to neutralise static
charge, smoothing the scales on the hair cuticle for shiny, conditioned
and manageable hair.
OPERATING INSTUCTIONS
•For optimum results, rough dry hair to remove the excess moisture
until it is around 80% dry.
•Ensure the hair is combed through to remove tangles prior to styling.
•Select the required heat/speed setting using the slide switch. Select
setting ‘I’ for a lower heat, ideal for shorter, ner hair. Select setting
‘II’ for a higher heat which is more suitable for longer or thicker hair.
•ALWAYS ensure to keep hair away from the rear lter to prevent it
being sucked into the fan as this may cause the styler to overheat.
•Separate hair into manageable sections.
•To create volume at the roots, take a section of hair and use the brush
to lift the hair at the roots, moving the styler slowly down through the
hair.
•For a smooth straight look, slowly brush down the hair length keeping
the hair as taut as possible.
•To create movement or shape at the ends of the hair, use the brush
to curl hair inwards or outwards.
•To set the style, move the slide switch to the cool position.
•Repeat as necessary on all sections of the hair.
•After use, switch off and unplug the appliance. Allow to cool before
storing away.

CLEANING & MAINTENANCE
To keep your styler in the best possible condition, please follow the
steps below:
•Do not wrap the lead around the styler, instead coil the lead loosely
by the side of the dryer when storing away.
• Do not use the styler at a stretch from the power point.
• Always unplug after use.
Cleaning the filter
• Ensure the styler is switched off, unplugged and cool.
• Holding the handle of the styler, gently release the rear lter
• Using a soft brush, clean any hair and other debris from the lter.
• Replace the rear lter by pushing back into position.
•To clean the outside of the styler, wipe with a damp cloth. Ensure the
dryer is completely dry before use and no water enters inside.
UK GARANTEE
This BaByliss PRO appliance is guaranteed for salon use for 6 months.
This guarantee covers defects under normal use from date of purchase
and ceases to be valid in the event of alteration or repair by unauthorised
persons. If the appliance does not perform satisfactorily due to defects
in materials or manufacture, it will be repaired or replaced through
Conair UK After Sales Service. The Conair Group Ltd reserves the right
to amend terms and specications without prior notice.
This guarantee in no way affects your statutory rights.
UK AFTER SALES SERVICE
For further advice on using the appliance, contact the Conair Customer
Care Line on 0870 5 133191 (09:00 to 17:00 Monday to Friday) or email
your enquiry to [e-mail]
If you should need to return your appliance to us please send it to the
following address:

Customer Care Centre,
Conair Logistics
Unit 4
Revolution Park
Buckshaw Avenue
Buckshaw Village
Chorley
PR7 7DW
Please enclose your name and address, together with a copy of proof
of purchase and details of the fault.
SAFE DISPOSAL
The symbol on the product or on its packaging indicates that this
product may not be treated as household waste. Instead it should be
handed to an appropriate collection point for the recycling of Electrical
and Electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for
the environment and human health, which could otherwise be caused
by inappropriate waste handling of this product. For more detailed
information about the recycling of this product, please contact your
local council ofce or your household waste disposal service.
UK WIRING INSTRUCTIONS
The wires in the mains lead are coloured in accordance with the
following code:
BLUE = NEUTRAL
BROWN = LIVE
As the colours in the wire of the mains lead of this appliance may not
correspond with the colour marking identifying the terminals on your
plug, proceed as follows:

• The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured black.
• The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured red.
• Neither core should be connected to the earth terminal of a three pin
plug marked with the letter E or or is coloured green or green and
yellow.
With this appliance, if a 13amp plug is used a 13amp fuse should be
tted. If any other type of plug is used, a 10 amp fuse must be tted
either in the plug or at the distribution board.