Backyard Creations 272-0961 User manual

INSTRUCTION MANUAL: SKU#272-0961 STEEL SCROLL GLIDER BENCH
CAUTION: Read all instructions before assembly. Failure to do so may result in faulty assembly and potential injury.
SPECIAL WARNINGS: Assemble on a soft, non-abrasive surface, such as carpet or cardboard to avoid damaging the item.
Noted: Identify all parts packed in carton against the parts list. Remove all the protective material carefully and DO NOT use
a knife to prevent scratching the surfaces. USE ONLY ON LEVEL SURFACES. INSPECT VISUALLY BEFORE EACH USE AND
ENSURE ALL HARDWARE IS PROPERLY TIGHTENED.
CUSTOMER SERVICE: For questions, assistance or repair parts, please call toll free at: 1-800-505-8305 (M-F 9:00am-
5:00pm Eastern Time) or visit us on the web www.americancustomerservice.com 24 hours a day.
PARTS LIST
REF.
PARTS
NAME
IMAGE
QTY
A
BASE LEG
2
B
BASE SUPPORT
2
C
GLIDING BAR
2
D
SEAT
1
E
BACK
1
F
ARMREST
2
H
M6*60mm
4
I
M6*35mm
8
J
M6*50mm
8
For missing parts, please call toll free customer
service number for further assistance.

K
M6*70mm
4
L
METAL WASHER
24
M
PLASTIC
WASHER
8
N
NUT
24
O
NUT CAP
24
P
BOLT CAP
24
Q
ALLEN KEY
1
R
WRENCH
1
ASSEMBLY INSTRUCTIONS
STEP ONE: AFFIX BASE
With help of one other person, carefully hold Base Support
(B) in place and align with holes in Base Leg (A)
Insert Bolt (I), Steel Washer (L) through Base Leg (A) and
then Base Support (B). Secure with Nut (N) using the
supplied Allen Key (Q) and Wrench (R)
Repeat with the other Base Leg and assemble the other
Base Support
Hold Gliding Bar (C) in place, short side up, and align with
holes in Base Leg (A)
Insert Bolt (J), Plastic Washer (M) through Gliding Bar (C)
and then Base Leg (A). Secure with Steel Washer (L) and
Nut (N) using the supplied Allen Key and Wrench
Repeat for the other side and assemble the other Gliding
Bar
Cover the assembled Nut and Bolts with Cap (O) and (P)

STEP TWO: AFFIX BENCH
Carefully hold Seat (D) in place and align with holes in the
middle part of Armrest (F)
Insert Bolt (J) through Armrest (F) and then Seat (D). Secure
with Nut (N) using the supplied Allen Key and Wrench
Repeat with the other Armrest
Hold Back (E) in place and align with holes on the top part
of Armrest (F)
Insert Bolt (K) through Armrest (F) and then Back (E).
Secure with Steel Washer (L) and Nut (N) using the
supplied Allen Key and Wrench
Repeat on the other side
Cover the assembled Nut and Bolts with Cap (O) and (P)
STEP THREE: ASSEMBLE BENCH WITH BASE
Move the assembled base and bench to desired location
Carefully hold assembled bench in place and align the
bottom part of Gliding Bar (C) with holes on the bottom
part of Armrest (F)
Place Plastic Washer (M) in between the Gliding Bar and
Armrest. Insert Bolt (H) through Armrest (F), Plastic Washer
(M) then Gliding Bar (C). Secure with Steel Washer (L) Nut
(N) using the supplied Allen Key and Wrench
Repeat on the other Gliding Bar
Repeat on the other side
Cover the assembled Nut and Bolts with Cap (O) and (P)

STEP FOUR: ENJOY
Now your glider bench is ready to use!
BACKYARD CREATIONS® MANUFACTURER‘S WARRANTY (Limited 1-Year Warranty)
This product is covered under the manufacturer’s one year limited warranty against defects in workmanship and materials. If your
product fails structurally during normal use within one year of purchase, the manufacturer will repair or replace the defective unit at no
charge. The warranty excludes furniture used for commercial purposes, furniture damaged by act of nature, abuse or lack of proper
care or corrosion or rusting of metal frame and hardware. Proof of purchase (dated register receipt) and in some cases photos of the
product are required for warranty claims. Maintain your outdoor furniture by using furniture covers and store away during extreme
weather conditions.
SAVE YOUR RECEIPTS. THIS WARRANTY IS VOID WITHOUT THEM.
Test Rite Products Corp. 1900 S. Burgundy Place, Ontario, CA 91761 Made in China