Backyard Products Heartland MANSFIELD GABLE User manual

16644-R
STOP!
STOP!
Call Us First!
DO NOT RETURN TO STORE.
For immediate help with assembly or product information
call our toll free number:
1- 800-577-9663
or email:
[e-mail]
Our staff is ready to provide assistance
April through October M-F 8:00 AM to 4:30 PM EST
Saturday 8:30 AM to 4:30 PM EST
November through March M - F 8:00 AM to 5:00 PM EST

(This page intentionally left blank.)

10-05-2017
KEEP THIS MANUAL FOR FUTURE REFERENCE
ACTUAL FLOOR SIZE IS 120 x 144" (304,8 x 365,8 cm)
16644-R
BEFORE YOU BEGIN
IMPORTANT!
READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.
•BUILDINGRESTRICTIONSANDAPPROVALS
Be sure to check with local building department and homeowners association for specic restrictions and/ or requirements before building.
.•ENGINEEREDDRAWINGS
Contact our Customer Service Team if engineered drawings are needed to pull local permits.
•SURFACEPREPARATION
To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are
listed on page 7.
•CHECKALLPARTS
Inventory all parts listed on pages 4 - 6. Contact our Customer Service Team if any parts are missing or damaged.
•ADDITIONALMATERIALS
You will need additional materials to complete your shed. See page 3 for required and optional materials and quantities.
MANSFIELD GABLE 10' x 12' (305 x 366 cm)
- CUSTOMER SERVICE -
Call: 1-800-577-9663 email: [email protected]
A Backyard Products Company

2
TOOLS
Safety! Always use approved safety glasses during assembly.
OptionalRequired
HELPFUL REMINDER SYMBOLS
Look for these symbols for helpful reminders throughout this manual.
ORIENT LUMBER AND TRIM FOR BEST APPEARANCE
= Assistance Required; two or more people.
= Ensure squareness.
= Important required step or operation.
= Helpful assembly hint.
= Mark part with pencil.
= Beginning of steps for assembly or installation.
= You have nished the assembly or installation.
= Level
❑Gloves
Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side.
Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way
negatively affect the strength or integrity of our product. (See Fig. A, B, C.)
A
❑Safety Glasses
❑Tape Measure
❑Paint Tools
❑Ladder
❑Caulk Gun
❑Hammer
❑Level
FINISH
BEGIN
❑Pencil
❑Phillips
Screwdriver ❑ Tool Belt/
Nail Pouch
❑Chalk Line
❑Nail Gun
• gun nails
❑Tin Snips
(for drip edge)
❑ Square or
❑Utility Knife
❑Shingle Blades
B C
❑ Drill / Driver
❑ 1/8" Drill Bit
❑#2 Philips Drive Bit
❑ 1/4" Drill Bit
❑ 5/16" Drill Bit
❑ 1/2" Drill Bit
❑Hand Saw

3
OPTIONAL MATERIALS
DRIP EDGE ..................... 60 Feet #15 ROOFING FELT
To cover 148 Sq. Ft. of roof area.
1"GALVANIZEDROOFINGNAILS.........1/4Lb
For roong felt.
REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER’S
INSTRUCTIONS FOR INSTALLATION OF SHINGLES, DRIP EDGE AND FELT.
COMPLETING YOUR SHED
You will need these additional materials:
3-TAB SHINGLES ............................. 7 Bundles
PAINT FOR SIDING .......................... 2 Gallons
Use 100% acrylic latex exterior paint. (2) coats recommended.
CAULK.................................................3Tubes
Use acrylic latex exterior caulk that is paintable.
1"GALVANIZEDROOFINGNAILS....3Lbs
For shingles.
PAINT FOR TRIM .............................1 Quart
Use 100% acrylic latex exterior paint.
WOODGLUE.......................ExteriorRated
REINFORCED WOOD FLOOR FRAME (OPTIONAL)
WOOD FLOOR FRAME
IMPORTANT! The included oor has been designed for general use. Depending on your specic use you may want to construct a
heavy duty oor frame by adding additional oor joists (shown below as shaded). Below is a list of additional materials (not included):
x3
x12
2 x 4 x 10' (5 x 10 x 304,8 cm) Treated Lumber
Cut to (3) 2 x 4 x 117" (5 x 10 x 297,2 cm)
ea. 3" (7,6 cm) Hot Dipped Galvanized Nails
Optional 12" (30,5 cm) spacing
Standard 16" (40,7 cm) spacing
FOUNDATION OR FLOOR MATERIALS
ADDITIONAL MATERIALS
• This shed does not include any oor or leveling materials.
• See the FLOOR LEVELING section on page 8 for recommended methods and suggested materials to properly level your
oor, as this will vary depending on your specic site.
NOTE: Use a minimum of 5/8" (1,6 cm) Oriented Strand Board (OSB)
5/8" x 48" x96"
(1,6 x 121,9 x 243,8 cm)
x3
FLOOR PANELSYou will need oor panels and nails to complete your oor.
Floor panel sizes and quantities are shown below.
2" (5,1 cm)
x1
1 lb. of 2" (5,1 cm) Hot
Dipped Galvanized
Box-TypeNails.
MATERIAL REQUIRED: Use only wood treated for ground contact and fasteners approved for use with treated wood.
x12 2 x 4 x 120" (5,1 x 10,2 x 304,8 cm)
HotDippedGalvanizedBox-TypeNails.
3" (7,6 cm)
x44
x2
2 x 4 x 144" (5,1 x 10,2 x 365,8 cm)

WOODSIZECONVERSIONCHART
Nominal Board Size Actual Size
1" x 4".................3/4" x 3-1/2" (1,9 x 8,9 cm)
2" x 4"..............1-1/2" x 3-1/2" (3,8 x 8,9 cm)
2" x 3"..............1-1/2" x 2-1/2" (3,8 x 6,3 cm)
1" x 3".................3/4" x 2-1/2" (3,8 x 6,3 cm)
PARTS IDENTIFICATION AND SIZES
RS RS
Part identication
letters are stamped on some parts.
Check these locations for
part stamp.
Treated lumber is stamped:
WALLS
x4 2 x 4 x 24" (5,1 x 10,2 x 61 cm)
RL
x26 2 x 4 x 80" (5,1 x 10,2 x 203,2 cm)
TK
x6 2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm)
YFA
x2 2 x 4 x 67" (5,1 x 10,3 x 170,2 cm)
AM
x4 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)
SP
x4 2 x 4 x 44-1/2" (5,1 x 10,2 x 113 cm)
STL
PARTS LIST
INVENTORYYOURPARTSbeforeyoubegin.
We suggest sorting parts by the category they are listed in.
RAFTERS
TRIM
x3 2 x 4 x 8-1/2" (5,1 x 10,2 x 21,6 cm)
CPA
x4 3/8 x 1-3/4 x 81-7/8" (1 x 4,4 x 208 cm)
x4 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)
TP
3/4"
(1,9 cm)
1 x 3 x 5" (2,5 x 7,6 x 12,7 cm) Gauge Block for 3/4" (1,9 cm) measurement
x1 GAA
DOOR
OO
x2 1-1/2 x 2-1/2 x 69" (3,8 x 6,3 x 175,3 cm)
x1 19/32 x 3 x 50-1/4" (1,5 x 7,6 x 127,6 cm)
GTR
x1 19/32 x 3 x 50-1/4" (1,5 x 7,6 x 127,6 cm)
GTL
4
x10 6 x 24" (15,2 x 61 cm) OSBORWOODGRAIN
x10 2 x 4 x 75-1/4" (5,1 x 10,2 x 191,1 cm)
ECN
19/32 x 3 x 72" (1,5 x 7,6 x 183 cm)
x1 ZJ
1 x 3 x 72" (1,6 x 7,6 x 182,9 cm)
x1 HJ
x4 19/32 x 3 x 26-5/8" (1,5 x 7,6 x 67,6 cm)
AH
x4 3/8 x 7-7/8 x 73-5/16" (1 x 20 x 186,2 cm)
x4 3/8 x 5-7/8 x 72-3/4" (1 x 14,9 x 184,8 cm)
x2 3/8 x 4-3/4 x 75-7/8" (1 x 12,1 x 197,2 cm)
x2 3/8 x 4-3/4 x 75-7/8" (1 x 12,1 x 197,2 cm)
x4 3/8 x 4-3/4 x 80-5/8" (1 x 12,1 x 204,8 cm)
x4 2 x 4 x 5-7/8" (5,1 x 10,2 x 14,9 cm)
PVA
x16 2 x 4 x 4-7/8" (5,1 x 10,2 x 12,4 cm)
CLA
x8 2 x 4 x 75-1/4" (5,1 x 10,2 x 191,1 cm) ECA
x4 3/8 x 1-3/4 x 82-1/2" (1 x 4,4 x 209,6 cm)
x2 2 x 4 x 22-1/2" (5,1 x 10,2 x 57,1 cm) AO
x1 2 x 4 x 12-1/2" (5,1 x 10,2 x 31,8 cm) AJ

PARTS LIST continued...
7/16 x 27-1/4 x 32-5/8"
(1,1 x 69,2 x 82,9 cm)
x4
7/16 x 27-1/4 x 48"
(1,1 x 69,2 x 121,9 cm)
x4 7/16 x 48 x 96"
(1,1 x 121,9 x 243,8 cm)
x2
7/16 x 32-5/8 x 48"
(1,1 x 82,9 x 121,9 cm)
x4
5
PANEL PARTS LIST
ROOF PANELS
SHELF - LOFT PANELS
SHELF - LOFT
NOTE: Panel parts are not stamped.
Roofpanelsare7/16"(1,1cm)thick.
3/8 x 8 x 12-1/2" (1 x 20,3 x 31,8 cm)
x6
x3 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)
TP
2 x 3 x10-1/8" (5,1 x 7,6 x 25,7 cm)
AE
x6
1 x 4 x 96" (2,5 x 10,2 x 243,8 cm)
x1 KP
WALL PANEL & DOORS PARTS LIST
x1
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
x1
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
2 x 4 x 24" (5,1 x 10,2 x 61 cm)
RL
x3
x1
23-7/8" x 96" (112,4 x 60,6 cm)
7/16 x 11-7/8 x 23-7/8" (1,1 x 30,2 x 60,6 cm)
x1
7/16 x 11-7/8 x 96" (1,1 x 30,2 x 243,8 cm)
x1
1 x 4 x 23-7/8" (2,5 x 10,2 x 60,6 cm)
JS
x1
3/8 x 23-7/8 x 84" (1 x 60,6 x 213,4 cm)
x2
x1
LEFT DOOR
x1
RIGHT DOOR
x2 x2x2
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
x7
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
x1

x310
x100
x16
x132
x140
x55
NAIL BOXES (not included)
VENT/ DOOR HARDWARE/ WINDOW
FASTENERS & HARDWARE
SHUTTERS
FASTENER/HARDWARE BAG
WORK BENCH PARTS
x20 1" (2,5 cm)
6
1-5/8" (4,1 cm)
2" (5,1 cm)
3" (7,6 cm)
3/4" (1,9 cm)
2" (5,0 cm)
x4 BOXES
x7 BOXES
3" (7,6 cm)
2" (5,1 cm)
1-1/2" (3,8 cm)
x8 1" (2,5 cm)
x2
x1 64" Metal Threshold
3/4" (1,9 cm) x11
Bagged separately / special coating x1
x4
3/4”TechScrewwithdrillpoint
1-1/4” x8
3-Point Door Locking Mechanism
x1
1-1/4” x2
1-1/4” x2
Handle (locking)
with Screws
x2
x4
x2
3/8" x5-1/2" (1 cm x 14 cm)
3/8" (1 cm)
3/8" (1 cm)
HexBolt
FlatWasher
Lock Nut
(NOTACTUALSIZE)
3/8 x 14-1/4 x 22-1/4" (1 x 36,2 x 56,5 cm)
x6
x1 1 x 4 x 96" (2,5 x 10,2 x 243,8 cm)
KP
2 x 3 x19" (5,1 x 7,6 x 48,3 cm)
LR
x6
1 x 4 x 23-7/8" (2,5 x 10,2 x 60,6 cm)
JS
x1
7/16 x 20-3/4 x 20-1/2" (1,1 x 52,7 x 52,1 cm)
x1
7/16 x 20-3/4 x 92-1/2" (1,1 x 52,7 x 235 cm)
x1
19/32 x 3 x 30-1/8" (1,5 x 7,6 x 76,5 cm)
x6 AZ
19/32 x 3 x 21" (1,5 x 7,6 x 53,3 cm)
x1 BWL
19/32 x 3 x 21" (1,5 x 7,6 x 53,3 cm)
x1 BWR
19/32 x 3 x 8" (1,5 x 7,6 x 20 cm)
x4 KV
x1
Window
22-1/2" x 29-3/4"
(57,1 x 75,6 cm)
x2
19/32 x 3 x 26-5/8"
(1,5 x 7,6 x 67,6 cm)
AH

7
FLOOR LEVELING OPTIONS
There are multiple ways to level your oor frame. Our recommended leveling method is shown below.
Leveling materials are not included in this kit.
PREFERREDMETHOD-4x4TREATEDRUNNERS
Measurements to
centersof4x4's.
• 3" Screws angled into 4x4.
• (2) at each point frame
•and 4x4 touch.
12"
(30,5 cm)
12"
(30,5 cm)
• Level under 4x4 runners only.
• Locate leveling material 12" from ends of runners and no more than 48" apart.
• Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use
shingles in direct contact with ground.
• For best results and aiding in water drainage use gravel under each concrete block.
LEVELINGMETHODS
• If you are building your shed on a concrete foundation see the following page.
CONCRETE
MATERIAL REQUIRED
x3 4" x 4" x 12' (10 x 10 x 366 cm)Treated Lumber
FastenersforFrameto4"x4".
(3" Screws shown as one option.) Minimum (60) 3" screws / exterior grade.
Use only wood treated for ground contact and fasteners approved for use with treated wood.
Always support frame seams.
Leveling higher than 16" not recommended.
LEVELINGMATERIALS
Gravel
2x4 Treated Lumber
Solid Masonry Blocks in 1", 2", 4" or 8" thickness
Asphalt Shingles
8" Block
4" Block
Gravel
Gravel
Do not exceed 16".
4x4 Runner
Shingle
Shingle
Maximum between leveling
material locations.
48"
12"
2x4 Treated Lumber
2" Block
Level
12"
DOOR
DOOR

8
CONCRETE FOUNDATION
Your kit contains all materials to construct a wooden oor. If you choose to install your kit
on a concrete slab refer to the diagram below.
• A treated 2 x 4" (5,1 x 10,2 cm) sill plate is required when installing your shed on concrete. Hint: Use treated lumber in your kit or
purchase full length treated lumber.
• Use a high quality exterior grade caulk beneath all sill plates.
• Fasten 2 x 4" (5,1 x 10,2 cm) sill plates to slab using approved concrete anchors (fasteners not included).
• Check local code for concrete foundation requirements.
NOTE:
Allow new concrete slabs to cure for at least seven (7) days.
2" x 4" x 11' (5,1 x 10,2 x 424 cm)
2" x 4" x 10' (5,1 x 10,2 x 304,8 cm)
Caulk
Requires:
x2
x2
x1
MUST be treated lumber.
MUST be treated lumber.
120" (304,8 cm)
120"x144"(304,8x365,8cm) 137" (348 cm)
10'x12'(243,8x365,8cm) 144" (365,8 cm)
AActual Size B CBuilding Size
A
B
C
4"
(10,2 cm)
3-1/2"
(8,9 cm)
Treated Sill Plate
Caulk between sill
plate and concrete.
TO ASSEMBLE YOUR FLOOR - PLEASE REFER TO
INSTRUCTIONSPROVIDEDWITHYOURFLOORKIT.

9
GABLE END
WALL
EAVESIDEWALL
GABLE END
WALL
EAVESIDEWALL
Checktheoorframeislevelafterinstallingoorpanels.
Re-level if needed.
HINT:
IMPORTANT!
•Theoorshouldbeusedasastableworksurfaceforwallconstruction.
• Organizeyourassemblyprocedureduringthebuildprocess
to avoid over-handling of the walls.

10
PARTS REQUIRED:
FINISH
3You have nished rafter jig. Proceed to assemble your rafters.
RAFTER ASSEMBLY
120"
(304,8 cm)
36"
(91,4 cm)
36"
(91,4 cm)
60"
(152,4 cm)
3/4"
(1,9 cm)
PVAx3
3" (7,6 cm)
x6
x3 PVA 2 x 4 x 5-7/8" (5,1 x 10,2 x 14,9 cm)
Measure over 60" and up 36" from the oor edges and secure the third PVA using two 3" screws.
Check this PVA is 36" at both ends for squareness.
BEGIN
¸
1Secure one PVA ush to the oor deck using two 3" screws.
Measure over 120-3/4" and install a second PVA ush to the oor deck. PVA will overhang the oor.
Secure using two 3" screws.
2
120-3/4"
(306,7 cm) IMPORTANT MEASUREMENT !!
Fig. B
Fig. A
Itisveryimportanttoassembleyourraftersusingthefollowingmethodforanevenandatroof.
You will build a rafter jig using the oor and three PVA parts as shown.
Floor Width
(2) 3" (7,6 cm)
Screws
in each PVA
There will be an
overhang on
this end.
Flush Flush

11
PARTS REQUIRED: x70 2" (5,1 cm)
x10
1-5/8" (4,1 cm)
RAFTER ASSEMBLY
x10
6 x 24" (15,2 x 61 cm)
OSBORWOODGRAIN
x10
2 x 4 x 75-1/4" (5,1 x 10,2 x 191,1 cm)
ECN
1/4" (1,9 cm)
GAP
1/4" (1,9 cm)
GAP
1/4" (1,9 cm)
GAP
1/4" (1,9 cm)
GAP
ECNx2
ECNx2
Fig. A
Fig. B
Fig. C
Glue where
gusset installs
KeepraftersrmlyagainstPVA at both ends when securing gusset.
You have nished assembling your rafters.
Repeat steps 1 through 3 to assemble four more rafters.
Remove PVA's from oor.
Flip rafters over and attach a second gusset using glue and (12) 2" nails. No need to use jig for this gusset.
4
5
3
2 Keep ECN rm against outside PVA's as shown (Fig.A) and push rafters tight to the middle PVA. Rafters should
touch at tips (Fig. A).
Apply glue to rafters where gusset will attach (Fig. B).
Place gusset onto ECN holding a 1/4" gap from edge (Fig. C) and keeping rafters rm as instructed. Secure
gusset using one 1-5/8" screw into each rafter. HINT: These screws will help hold the measurements when you
nail on gussets.
Use ten 2" nails to nish securing the gusset to the rafters to pattern shown in Fig. C.
BEGIN
¸
1Place two rafters ECN into the jig as shown.
FINISH
6
1-5/8"(4,1cm)
Screw
120-3/4"
(306,7 cm)

FRONT WALL
PARTS REQUIRED:
HINT:
For easier nailing
stand on frame.
12
x48 3" (7,6 cm)
BEGIN
1
Use two 3" nails at each mark.
Orient parts on edge on oor. Measure and mark.
2
TKx6
TP
TP SP
SP
AO
AO
AM
x2 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)
TP
x6 2 x 4 x 80" (5,1 x 10,2 x 203,2 cm)
TK
x2 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)
SP
x2 2 x 4 x 22-1/2" (5,1 x 10,2 x 57,1 cm)
AO
x1 2 x 4 x 67" (5,1 x 10,2 x 170,2 cm)
AM
x3 2 x 4 x 8-1/2" (5,1 x 10,2 x 21,6 cm)
CPA
CPAx3
144"
(365,8 cm)
67"
(170,2 cm)
1-1/2"
(3,8 cm)
124-1/2"
(316,2 cm)
100-1/2"
(255,3 cm)
80"
(203,2 cm)
96"
(243,8 cm)
48"
(122 cm)
48"
(122 cm)
72"
(183 cm)
24"
(61 cm)
24"
(61 cm)
19-1/2"
(49-1/2 cm)
13-3/4"
(35 cm)
8-1/2"
(21,6 cm)
96"
(243,8 cm)
18-1/4"
(46,4 cm)
30"
(76,2 cm)
36"
(91,4 cm)
13-3/4"
(35 cm)
3" (7,6 cm)
Nails
82-1/4"
(208,9 cm)

HINT:
For easier nailing
stand on frame.
13
3
FRONT WALL
PARTS REQUIRED: 3" (7,6 cm)
x40
Orient parts on edge on oor as shown. Use two 3" nails as shown.
Use two 3" nails at each mark and four 3" nails at seams.
TK
TOENAILING
48"
(122 cm)
48"
(122 cm)
24"
(61 cm)
AM
AJ
x1 2 x 4 x 67" (5,1 x 10,2 x 170,2 cm)
AM
x2 2 x 4 x 68-1/2" (5 x 10,2 x 174 cm)
YFA
YFA
3" (7,6 cm)
Nails
Two nails at
each location.
x1 2 x 4 x 80" (5,1 x 10,2 x 203,2 cm)
TK
x1 2 x 4 x 12-1/2" (5,1 x 10,2 x 31,8 cm)
AJ

14
FRONT WALL
PARTS REQUIRED: x62 2" (5,1 cm)
Fig. B
Fig. A
3/4"
(1,9 cm)
3/4"
(1,9 cm)
2 Nails
2 Nails
48 x 84"
(121,9 x 213,4 cm)
x1
Place 48x84" panel onto wall frame ush to top of frame with primed side up as shown.
Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with two 2" nails
in the corners (Fig. A).
Nail the panel using 2" nails 6" apart on edges and 12" apart inside panel.
Ensure your wall frame is square by installing one panel and squaring frame.
Move to the opposite end. Using the long edge of the panel as a lever move the panel side-to-side until you have
a 3/4" measurement on the wall stud. Secure corner with two 2" nails (Fig. B).
5
6
4
3/4"GAUGE
BLOCK
GAA
3/4"GAUGE
BLOCK
Primed
side up
BEGIN HERE
Forsquarenessmaintainushand
3/4"measurementalongpaneledges.
Flush
48"
(122 cm)
3/4"
(1,9 cm)
3/4"
(1,9 cm)
12"
(30,5 cm)
6"
(15,2 cm)

15
Place left 48"x84" panel on frame as
shown with primed side facing up.
Nail using 2" nails 6" apart on
panel edges .
7
Place right 48"x84"panel on frame as
shown with primed side facing up.
Nail using 2" nails 6" apart on
panel edges.
8
You have nished building your FRONT WALL.
FINISH
10
x90
FRONT WALL
PARTS REQUIRED: 2" (5,1 cm)
9Carefully ip the FRONT WALL over.
48 x 84"
(121,9 x 213,4 cm)
x1LEFT
48 x 84"
(121,9 x 213,4 cm)
1 RIGHT
Primed
side up
Primed
side up
Forsquarenessmaintainushand
3/4"measurementalongpaneledges.
Forsquarenessmaintainushand
3/4"measurementalongpaneledges.
Flush
Flush
3/4"
(1,9 cm)
3/4"
(1,9 cm)
6"
(15,2 cm)
6"
(15,2 cm)

BACK WALL
PARTS REQUIRED:
96"
(243,8 cm)
120"
(312,4 cm)
72"
(182,9 cm)
48"
(121,9 cm)
24"
(61 cm)
80"
(203,2 cm)
1-1/2”
(3,8 cm)
1-1/2"
(3,8 cm)
1-1/2"
(3,8 cm)
144"
(356,8 cm)
48"
(121,9 cm)
96"
(243,8 cm)
96"
(243,8 cm)
TKx7
SP
TP
TP
SP
HINT:
For easier nailing
stand on frame.
x2 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)
TP
x7 2 x 4 x 80" (5,1 x 10,2 x 203,2 cm)
TK
x2 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)
SP
x32
16
3" (7,6 cm)
BEGIN
1Orient parts on edge on oor. Measure and mark.
Use two 3" nails at each mark and four 3" nails at seams
2
TOENAILING

17
ForsquarenessmaintainFlushand3/4"
measurement along panel edges.
BACK WALL PANELS
48 x 84"
(121,9 x 213,4 cm)
PARTS REQUIRED:
x1
x45 2" (5,1 cm)
Fig. B
BEGIN HERE
Fig. A
3/4"
(1,9 cm) 3/4"
(1,9 cm)
2 Nails
2 Nails
Flush
48"
(121,9 cm)
3/4"
(1,9 cm) 1”
(2,5 cm)
3/4"
(1,9 cm)
12"
(30,5 cm) 6"
(15,2 cm)
Place 48x84" panel onto wall frame ush to top of frame with primed side up as shown.
Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with
two 2" nails in the corners (Fig. A).
Nail the panel using 2" nails 6" apart on edges and 12" apart inside panel.
Ensure your wall frame is square by installing one panel and squaring frame.
Move to the opposite end. Using the long edge of the panel as a lever move the panel side-to-side until you have
a 3/4" measurement on the wall stud. Secure corner with two 2" nails (Fig. B).
4
5
3
3/4"GAUGE
BLOCK
GAA
3/4"GAUGE
BLOCK
Primed
side up

18
3/4"
(1,9 cm)
48"
(121,9 cm)
12"
(30,5 cm)
6"
(15,2 cm)
Flush
48"
(121,9 cm)
12"
(30,5 cm)
6"
(15,2 cm)
Flush
Forsquarenessmaintainushand
3/4"measurementalongpaneledges.
Forsquarenessmaintainush
along panel edges.
Place center 48"x84" panel on frame
as shown with primed side facing up.
Nail using 2" nails 6" apart on edges
and 12" apart inside panel.
6
Place end 48"x84"panel on frame as
shown with primed side facing up.
Nail using 2" nails 6" apart on edges
and 12" apart inside panel.
7
You have nished building your BACK WALL.
FINISH
9
Primed
side up
Primed
side up
x2
x90
BACK WALL PANELS
PARTS REQUIRED: 2" (5,1 cm)
8Carefully ip the BACK WALL over.
3/4"GAUGE
BLOCK
GAA
3/4"GAUGE
BLOCK
48 x 84"
(121,9 x 213,4 cm)