Badger Basket 02250 User manual

4.0/1008/TG
MODEL NUMBERS:
02250 - White
02251 - Natural
02252 - Cherry
Page 1 of 6
SLEIGH STYLE BABY
CHANGING TABLE WITH
LOWER STORAGE CART
Assembly
Instructions.
AdultAssembly
Required.
Save these
instructions for
future use.
Visit us online at www.badgerbasket.com
Toll-Free Customer Service: 1-800-236-1310 (Monday through Thursday 7:30 AM to 4:30 PM CST)
Web: http://www.badgerbasket.com/parts • E-mail: p[email protected]
Mail: PO Box 227, Edgar, WI 54426-0227 • Phone: [phone] • Fax: [phone]

4.0/1008/TG
BEFORE YOU BEGIN ASSEMBLY:
Check all parts and hardware. If anything is missing or not
satisfactory, please DO NOT call the store where purchased or
return the product to them. Contact Badger Basket for assistance.
Most problems are resolved without you needing to leave home.
When contacting us, please have this instruction manual, your
product model number, and your product version code ready.
For fastest service, go to
http://www.badgerbasket.com/parts
Your Product Version Code is: 4.0/1008/TG
USE AND CARE INSTRUCTIONS:
Wipe the table, pad, and safety belt clean with a damp cloth and mild soap as needed.
READ ALL INSTRUCTIONS before use of this changing table. Keep instructions for
future use. Choking Hazard! Keep unassembled parts out of the reach of small
children. Use only the parts, hardware, and changing pad provided by Badger
Basket. Do not use the changing table if it is damaged or broken.
FALL HAZARD - To prevent death or serious injury, always keep baby within arm’s
reach.
NEVER leave your baby unattended, not even for a moment, when you are chang-
ing Baby’s diaper.ALWAYS use the safety belt provided; and as an extra precaution
keep at least one hand on your baby at all times.
DO NOT allow any children to climb or play on the table.
Periodically check to make sure all the bolts and screws remain tight.
This table is suitable for use with children weighing up to 30 lbs. (13.64 kg).
WARNING - FAILURE TO FOLLOW THESE WARNINGS
AND THE INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH
Page 2 of 6

4.0/1008/TG
TABLE PARTS INCLUDED:
(A) 14 - Pegs*
(B) 2 - Top Rails
(C1) 2 - Top Shelf Rails**
(C2) 3 - Middle/Lower Shelf Rails
(D) 2 - End Panels
(E) 14 - Bolts
(F1) 1 - Top Shelf Panel**
(not shown)
(F2) 1 - Middle Shelf Panel**
(not shown)
(G) 1 - Safety Belt
(H) 1 - Metal Support Bar
(I) 2 - Long Screws
(J) 1 - Mattress/Pad (not shown)
STORAGE CART PARTS INCLUDED:
(E) 8 - Bolts
(K) 2 - Front/Rear Panels
(L) 2 - Side Panels
(M) 1 - Bottom Panel
(N) 4 - Wheels
(O) 16 - Short Screws
(P) 8 - Barrel Nuts
(Q) 1 - Support Bar
Page 3 of 6
PARTSAND HARDWARE:
Bx2
C1x2
C2x3
Dx2
Gx1
Hx1
Ax14*
Nx4
Ox16
Px8
Ex22 Ix2
Kx2
Lx2
Mx1
Qx1
TOOL NEEDED:
Phillips Screwdriver (not included)
Power driver is helpful but be careful not to damage the product.
ASSEMBLY NOTES:
Parts & Hardware diagrams not to scale.
* Style of PEGS may vary from shown
** The two TOP SHELF RAILS have a larger
shelf groove than the other three rails. The
TOP SHELF PANEL is thicker than the
middle shelf panel.

4.0/1008/TG
PICTURE 4C
Page 4 of 6
STEP 1: See PICTURE 1. Insert FOURTEEN PEGS (A) into the peg holes on the ends of the TWO TOP RAILS (B)
and the FIVE SHELF RAILS (C1, C2).
STEP 2: See PICTURE 2. Attach the TWO TOP RAILS (B), TWO TOP SHELF RAILS (C1), and THREE MIDDLE/
LOWER SHELF RAILS (C2) to ONE END PANEL (D) using SEVEN BOLTS (E). Be sure the shelf grooves on the
rails line up with the shelf grooves on the end panel.
C1
STEP 3: See PICTURE 3. Rest the table on the END
PANEL (D). Insert the TOP SHELF PANEL (F1) and
MIDDLE SHELF PANEL (F2) into the grooves on the
SHELF RAILS (C1, C2) with the white or the colored
sides facing up (depending on your model). Be sure the
shelves are seated into the grooves on all three sides. PICTURE 2
PICTURE 1 A
BC1, C2
B
B
D
STEP 4: See PICTURE 3. Attach the second END PANEL (D) to the TWO TOP RAILS (B) and the FIVE SHELF
RAILS (C1, C2) using SEVEN BOLTS (E). Be sure the TWO SHELF PANELS (F1, F2) are properly seated in the
grooves on all sides.
STEP5: See PICTURES 4A, 4B and 4C. Slip one end of the SAFETY BELT (G) between the TOP RAIL (B) and the
TOP SHELF RAIL (C1). Using the pre-made holes on the SAFTEY BELT (G) and the underside of the TOPSHELF RAIL
(C1), sandwich the end of the SAFETY BELT (G) between the METAL SUPPORT BAR (H) and the top shelf rail as shown
and secure with ONE LONG SCREW (I). Repeat to secure the other ends of the safety belt and the metal bar.
PICTURE 3
D
F1 F2 PICTURE 4B
G
BH
BC1
G
F1
PICTURE 4A
C2
C1
*You must be sure to
use the C1 rails with
thethickergrooves
in the top positions.
*You must be sure to
usethethicker F1
shelf in the top
position.

4.0/1008/TGPage 5 of 6
L
PICTURE 7 PICTURE 8
PICTURE 5
KL
M
N
K
L
M
STEP 8: See PICTURE 7. Attach the remaining SIDE PANEL (L) to both FRONT/REAR PANELS (K) using FOUR
BOLTS (E) and FOUR BARREL NUTS (P). Be sure the BOTTOM PANEL (M) is seated in the groove.
STEP 9: See PICTURE 8. Turn the storage cart upside down. Attach one WHEEL (N) to each corner of the BOTTOM
PANEL (M) using FOUR SHORT SCREWS (O) for each wheel.
STEP 6: See PICTURE 5. Attach ONE FRONT/REAR PANEL (K) to ONE SIDE PANEL (L) using TWO BOLTS (E)
and TWO BARRELNUTS (P).The grooves face in and line up. Insert the SUPPORT BAR (Q) into the hole in the center
of the REAR PANEL (K).
STEP7: See PICTURE 6.Attach the SIDE PANEL(L) to the remaining FRONT/REAR PANEL(K) usingTWO BOLTS
(E) and TWO BARRELNUTS (P). The grooves face in and line up and the SUPPORT BAR (Q) is inserted and secure on
both sides. Slide the BOTTOM PANEL(M) into the grooves making sure it is properly seated on all sides. The white or the
colored side (depending on your model) faces up.
Q

4.0/1008/TGPage 6 of 6
J
YOUR CHANGING TABLE IS NOWASSEMBLED!
DO NOT USE THIS PRODUCT UNTILYOU HAVE
REVIEWED THE SAFETY
INSTRUCTIONS ON PAGE 2!
Remember that you can accessorize this table with Badger
Nursery Baskets (sold separately)!
Browse our selection at www.badgerbasket.com!
STEP10: See PICTURE 9. Turn the table right side up. Place the MATTRESS/PAD (J) onto the TOP
SHELF PANEL (F1) underneath the SAFETY BELT (G). Insert the STORAGE CART into the space
beneath the table as shown. The cart does not attach to the table. It remains independent so that you can
use it with the table, or use it elsewhere in the house.
PICTURE 9
Baskets shown with table here are not included.
You may purchase them separately if you wish.