Badger Meter Trimble Ranger 3 User manual

Trimble® Ranger 3
ORION® Field Application Software
ORI-PM-00100-EN-03 (May 2015 ) Installation Manual

Trimble® Ranger 3, ORION® Field Application Software
Page ii May 2015ORI-PM-00100-EN-03

CONTENTS
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Audience and Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Removing Previous Software Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
No Previous Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Removing Software Using Factory Reset/Clean Boot (Recommended). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Removing Software Using Remove Programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Removing Software in Kiosk Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Transferring Software File from the DVD to a USB Memory Stick. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing Software on the Handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Activating Kiosk Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Check COM Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installation Manual
Page iiiMay 2015 ORI-PM-00100-EN-03

Trimble® Ranger 3, ORION® Field Application Software
Page iv May 2015ORI-PM-00100-EN-03

INTRODUCTION
The ORION® Field Application 4.x.x for Trimble® Ranger 3 is a software application designed for automated and manual meter
reading of ORION water and gas endpoints. This manual is the guide for installing the ORION Field Application software on a
Trimble Ranger 3 handheld computer.
Audience and Purpose
Instructions are included for Trimble Ranger 3 handheld users who are installing the ORION Field Application 4.x.x software
for the first time, and for users who are updating to version 4.x.x.
System Requirements
The handheld must meet the system specifications as identified in the most recent version of the ORION Trimble Ranger 3
Product Data Sheet, available at www.badgermeter.com.
The ORION Field Application software requires a Trimble Ranger 3 handheld with a Windows® Mobile 6.5 Professional
operating system to run correctly. The Windows Mobile operating system version number can be found on the About screen
on the handheld. Go to Windows Start> Settings> System> About to access the About screen.
About this Manual
This manual includes step-by-step instructions for installing the ORION Field Application software and includes the following
two main sections:
• Removing Previous Software Versions
• Installing ORION Field Application 4.x.x Software
OTE:N To provide the best solution for our customers, Badger Meter continually improves software programs and
periodically updates this manual to reflect upgrades. Therefore, some discrepancies may be detected between the
installed software and this manual. The software version number on the screen images may differ from the version of
software you are installing.
Typographic Conventions
• Items on the software screens that you will be asked to select or choose by clicking a button, highlighting, checking a
box or another similar means are in bold text and capitalized in the manual.
Example: Tap the View Report button.
• Names of options, boxes, columns, fields and sections are italicized. In most cases, first letters will be capitalized.
Example: The value displays in the Status Information field.
• Messages and special markings are shown in quotation marks.
Examples: “Service Stopped” is shown on the display.
Introduction
Page 5May 2015 ORI-PM-00100-EN-03

REMOVING PREVIOUS SOFTWARE VERSIONS
Before installing the new software, remove all older versions of the software on the handheld.
The Factory Reset/Clean Boot method (1) is recommended. Read the descriptions below and choose the appropriate
procedure based on your handheld setup.
1. Removing the Previous Software Version Using Factory Reset/Clean Boot (Recommended)
Factory reset or "Clean Boot" is the recommended method for removing previous versions of the meter reading
software. This procedure resets the Trimble Ranger to "factory fresh" condition and removes all previously added
software. Refer to "Removing Software Using Factory Reset/Clean Boot (Recommended)" on page 7.
IF YOU ADDED ADDITIONAL SOFTWARE TO THE HANDHELD THAT YOU DO NOT WANT TO REMOVE, SEE THE
ALTERNATIVE METHOD, "REMOVING SOFTWARE USING REMOVE PROGRAMS" ON PAGE 8.
2. Removing the Previous Software Version Using Remove Programs (Alternative)
The Windows tool, "Remove Programs," allows you to select the programs you want to remove. It can be used
when the handheld has other software that you do not want to remove. Refer to "Removing Software Using Remove
Programs" on page 8.
3. (Kiosk mode) Removing the Previous Software Version
For handhelds in Kiosk mode, use procedure 1, "Removing Software Using Factory Reset/Clean Boot (Recommended)" on
page 7, to remove previous Kiosk software and all other previously added software.
If you previously added software to the handheld that you do not want to remove, use the instructions "Removing
Software in Kiosk Mode" on page 11.
No Previous Software
If there is no previous version of the ORION Field Application software on the handheld, go directly to "Installing Software" on
page 14.
Removing Previous Software Versions
Page 6 May 2015ORI-PM-00100-EN-03

Removing Software Using Factory Reset/Clean Boot (Recommended)
IF YOU ADDED ADDITIONAL SOFTWARE TO THE HANDHELD THAT YOU DO NOT WANT TO REMOVE, USE THE
ALTERNATIVE METHOD, "REMOVING SOFTWARE USING REMOVE PROGRAMS" ON PAGE 8.
Power on the handheld and start the factory reset (clean boot).
1. Press and hold the green power key. When the countdown timer starts, release the green power key.
Result: The Power Menu displays (Figure 1).
2. On the Power Menu, tap Reset and immediately PRESS and HOLD both the green power key and the RIGHT key on
the handheld keypad.
Figure 1: Power Menu
Figure 2: Hold power key and RIGHT key at the same time
3. When the Clean Boot screen appears, as shown in Figure 3, release both the green power key and the RIGHT key.
4. Use the up/down navigation arrows on the keypad to
select the Ok button on the Clean Boot screen.
Then press the ENTER key on the keypad to completely
clear the handheld.
OTE:N Tapping does not work on the Clean Boot screen.
Use the keypad.
Result: Several screens display during the next few seconds:
Blank screen, "Scanning...Wait" screen, Windows Embedded
screen, Finalizing screen, blank screen again, and then the
Windows Embedded screen again.
5. Touch the handheld screen to start the reset process as
instructed on the screen.
Figure 3: Clean Boot screen
6. Align the touch screen by tapping the cross hairs. Continue to tap the cross hairs until the screen aligns.
7. At the Password screen, tap Skip.
8. Tap the Complete screen to nish the reset.
OTE:N After performing a factory reset, the handheld date and time need to be reset. Tap Windows Start> Settings>
Clocks & Alarms to set the correct time and date.
The handheld is now ready for the new software installation. Refer to "Installing Software" on page 14.
Press &
hold
Press &
hold
Removing Previous Software Versions
Page 7May 2015 ORI-PM-00100-EN-03

Removing Software Using Remove Programs
Power on the handheld to start the software removal. Use this method if there is additional software on the handheld that
you do not want to remove.
1. At the home screen, tap Windows Start in the lower
left corner.
2. Scroll to nd Settings. Tap Settings.
Figure 4: Settings> System tab
3. Tap System> Remove Programs. You may need to scroll
to nd the icons.
Result: The Remove Programs screen opens.
4. Scroll to nd the Badger Meter software in the list of
programs.
OTE:N The folder name may be different than the one
shown, depending on the software version you
are removing, but should have “Badger Meter,“
“BMI“ or “Badger “ in the name.
5. Tap the le to select it. Then tap the Remove button.
Result: A pop-up window opens to conrm removal as
shown in Figure 7.Figure 5: Remove Programs
Figure 6: Remove Programs screen Figure 7: Confirm program removal
6. Tap Yes to conrm the program removal.
Result: The program le is removed from the list.
Removing Previous Software Versions
Page 8 May 2015ORI-PM-00100-EN-03

7. To complete the removal, tap Windows Start .
8. Scroll to nd File Explorer. Tap File Explorer.
9. Tap in the title bar to show My Device.
Figure 8: My Device
10. Tap My Device> Windows folder> Start Menu folder>
Programs folder.
11. Find the Badger Meter software applications folder as
shown in Figure 10.
OTE:N The folder name may be different than the one
shown, depending on the software version you
are removing.
Figure 9: My Device
12. Tap and hold the Badger Meter software applications folder until a menu displays as shown in Figure 11.
Then tap Delete.
Figure 10: Badger Meter software applications Figure 11: Delete
Removing Previous Software Versions
Page 9May 2015 ORI-PM-00100-EN-03

13. Tap in the title bar to show My Device.
14. Tap to open the Application Data folder.
15. Find the Badger Meter application data folder. In
Figure 13, the folder is labeled BMI_APP_DATA.
OTE:N The folder name may be different, depending on
the software version you are removing. Look for a
folder with“Badger Meter,“ “BMI“ or “Badger“ in
the name.
Figure 12: Application Data folder
16. Tap and hold the Badger Meter application data folder until a menu displays as shown in Figure 14.
Then tap Delete.
Figure 13: BMI App Data folder Figure 14: Delete
Result: All the meter reading software files are removed. The handheld is ready for the new software installation. Refer to
"Installing Software" on page 14.
Removing Previous Software Versions
Page 10 May 2015ORI-PM-00100-EN-03