Balkene Home GREENWICH STORAGE SHELF 63966 User manual

GREENWICH COLLECTION
STORAGE SHELF
Item#: 63966
SAVE THESE
INSTRUCTIONS FOR
FUTURE REFERENCE.
06092021
Questions, problems, missing parts?
Before returning to your retailer, our Florida-based customer service team is available.
Call toll-free [phone] 9 a.m. – 9 p.m., EST
Email
Live chat
[email protected]
www.balkenehome.com 9 a.m. – 6 p.m., EST, Monday – Friday
ATTACH YOUR RECEIPT HERE
Keep a copy of your proof of purchase or order
confirmation which will be needed if you need to
contact us about warranty coverage.
Purchase Date:

INFORMATION
BEFORE YOU BEGIN
GENERAL INFORMATION
This item is made of manufactured particle board and MDF materials. For safe assembly, set up on a
dry, soft, secure and clean surface. Do not clean with detergent or chemicals. Do not sit or stand on
the unit. Do not place hot items such as coffee cups directly on the surface of this furniture item. Keep
away from direct sunlight and water. Do not drag the unit. For indoor use only.
SAFETY INFORMATION
WARNING
This item is for storage/display of objects. Do NOT use as a step or ladder. DO NOT sit, stand, or climb or
allow children to sit, stand, or climb on the assembled product. Make sure connectors are securely in
place. After assembly, anchor the shelf to the wall for additional security, especially in environments with
small children or pets. Perform periodic checks to make sure the assembly connectors and anchors are
secure and adjust if needed. Keep unassembled parts and hardware away from children and infants. This
package contains small parts and sharp points. Adult assembly required.
CAUTION
READ all instructions before beginning assembly. Failure to do so may result in faulty assembly and
potential injury. Assemble the item on a soft, non-abrasive surface such as carpet or cardboard to avoid
damaging the item.
Max safe load limit: 10 KG / 22 LB per shelf.
Before beginning assembly, make sure all parts are present. Compare parts received with the “Parts
List.” If any part is missing or damaged, do NOT attempt to assemble the product. Please read and
understand this entire manual before attempting to assemble, operate or install this product. If you
have any questions regarding the product, please contact Customer Service:
Call toll-free 9 a.m. – 9 p.m., EST
Email
Live chat
[phone]
[email protected]
www.balkenehome.com 9 a.m. – 6 p.m., EST, Monday – Friday
Contact us for assistance: [phone] | www.balkenehome.com
2

PARTS LIST
HARDWARE CONTENTS
A
B
C
D
E
H
PART DESCRIPTION QTY
ATop Shelf 1
B2nd Shelf
C3rd shelf
D4th Shelf
1
1
1
EBottom Shelf
FShelf Support
1
5
GTop Rear Support
HDivider
1
2
ICabinet Side
J
1
1
K1
Top Left Side
Top Right Side
L1
Bottom Left Side
1
Cam Bolt
Qty: 18
2
Cam Lock Nut
Qty: 18
3
Dowel
Qty: 72
4
Screw 4x35mm
Qty: 10
Foot Pad
Qty: 4
5
Screw 4x50mm
Qty: 22
6
Hinge
Qty: 2
7
Screw 4x12mm
Qty: 12
8
Handle
Qty: 1
Backer Brace
Qty: 8
Screw 3x16mm
Qty: 8
Wall Anchor
Qty: 2
FF
GF
F
F
H
II
N
J
M1
Bottom Right Side
N1
Upper Shelf Backer
O1
Lower Shelf Backer
P1
Door
M
L
O
K
P
9
Screw 3x12mm
Qty: 2
Contact us for assistance: [phone] | www.balkenehome.com
3

ASSEMBLY
TO ANCHOR THE UNIT TO A WALL (RECOMMENDED), YOU WILL NEED: Power Drill with 6mm or 1/4" bit
PREPARATION
Before beginning assembly, be sure to empty contents of carton and make sure all parts are present. If any parts are missing,
please contact Customer Service before proceeding.
Place all parts on a soft, level surface for assembly. Estimated Assembly Time: 90 Minutes | DO NOT over-tighten hardware.
YOU WILL NEED FOR ASSEMBLY (not included): Rubber Mallet* Phillips-head Screwdriver
*If no mallet is available, use a hammer, but add padding as necessary to protect parts and surfaces.
1Insert Dowels 3 into the 2 holes closest to the center of the
bottom edge of a Divider H.
ASSEMBLY NOTE: You may need to tap gently with a rubber
mallet to fully seat Dowels throughout the assembly process.
Insert the other end of the Dowels into the holes in the top
surface of 2nd Shelf B. Secure the panels together by inserting
2 Screws 4 through the underside of the Shelf and into the
Divider. Tighten using a Phillips-head screwdriver.
Hardware Used: 3 Dowel x 2
4 Screw (4x35mm) x 2
H
B4
3
2Insert Cam Bolts 1 into the 2 indicated holes below the
"window" of Top Left Side J.
ASSEMBLY NOTE: Use a Phillips-head screwdriver to
tighten each Cam Bolt you install until its threads are fully
inserted.
Hardware Used: 2 Cam Lock Nut x 2
3 Dowel x 6
1
Hardware Used: 1 Cam Bolt x 2
J
3Insert Dowels 1 into the 2 remaining holes below the
"window" of Top Left Side J and the 2 pairs of holes near
the top corners of the panel.
Slide the hardware installed at the center of Side J into
the left edge of 2nd Shelf B.
Fasten the panels together by inserting a Cam Lock Nut 2
(with arrow pointed toward edge) into the hole adjoining
each Cam Bolt, then turning the Cam Lock Nuts clockwise
until secure.
Slide 2 Lower Shelf Supports F onto the 2 remaining pairs
of Dowels installed in Side J as shown.
F
H
B
J
G
2
3
3
3
1
Contact us for assistance: [phone] | www.balkenehome.com
4

ASSEMBLY
4Insert Cam Bolts 1 into the 2 indicated holes below the
"window" of Top Right Side K.
Hardware Used: 1 Cam Bolt x 2
K
1
1
5
Hardware Used: 2 Cam Lock Nut x 2
3 Dowel x 6
Insert Dowels 3 into the 2 remaining holes below the
"window" of Top Right Side K and the 2 pairs of holes
near the top corners of the panel.
Slide the hardware installed at the center of Side K into
the right edge of 2nd Shelf B. At the same time, insert the
2 pairs of Dowels into the ends of the 2 Lower Shelf
Supports F.
Fasten the panels together by inserting a Cam Lock Nut 2
(with arrow pointed toward edge) into the hole adjoining
each Cam Bolt, then turning the Cam Lock Nuts clockwise
until secure.
K
J
33
2
G
F
H
B
6Insert Cam Bolts 1 into the 2 indicated holes on
the underside of Top Shelf A.
1 Cam Bolt x 2 A
1
1
Hardware Used: 2 Cam Lock Nut x 2
3 Dowel x 10
5 Screw 4x50mm x 8
7Insert a total of 10 Dowels 3 into the holes along the top
edge of the partially-assembled unit as shown. Fit the
Top Shelf A onto the Dowels while inserting the Cam
Bolts into the holes in the top of the Divider H.
To secure the Top Shelf to the top of the unit, insert a
Cam Lock Nut 2 (with arrow pointed toward top) into
the hole adjoining each Cam Bolt, then turning the Cam
Lock Nuts clockwise until secure. Then, insert 8
Screws 5 through the holes in the underside of the
top edges of panels F/G/J/K and tighten into the
bottom of the Top Shelf.
K
J
B
3
3

Hardware Used:
2
H
Contact us for assistance: [phone] | www.balkenehome.com
5
A




ASSEMBLY
8Insert Cam Bolts 1 into the 2 indicated holes on
the underside of rd Shelf C.
1 Cam Bolt x 2
Hardware Used: 3 Dowel x 4
4 Screw mm x 4
9Slide the Upper Shelf Backer N into the groove running
along the rear of the unit as shown. Push it up to settle in
the groove along the bottom of d Shelf B.
Insert 4 Dowels 3 into the holes along the bottom edges
of the partially-assembled unit as shown. Fit the rd
Shelf C onto the Dowels.
To secure the rd Shelf to the Sides, insert 4 Screws 4
through the holes in the bottom of rd Shelf and tighten
firmly into the bottom edge of each Side using a Phillips-
head screwdriver.
Hardware Used:
C
1
1
K
3
4
4
J
B
NC
10 Insert Cam Bolts 1 into the 2 indicated holes on
the underside of th Shelf D.
1 Cam Bolt x 2
Hardware Used:
D
1
1
Insert Dowels 3 into the 2 holes closest to the center of the
bottom edge of the remaining Diider H.
Insert the other end of the Dowels into the holes in the top
surface of th Shelf D. Secure the panels together by inserting
2 Screws 4 through the underside of the Shelf and into the
Diider. Tighten using a Phillips-head screwdriver.
Hardware Used: 3 Dowel x 2
4 Screw mm x 2
11
D
4
H
4
Contact us for assistance: [phone] | www.balkenehome.com
6
3

ASSEMBLY
12Insert Dowels 3 into the 2 indicated holes on the
underside of th Shelf D. Fit the top edge of the
Caiet Side I onto the hardware on the bottom of
Shelf D.
Fasten the panels together by inserting a Cam Lock
Nut 2 (with arrow pointed toward the top) into the
hole adjoining each Cam Bolt, then turning the Cam
Lock Nuts clockwise until secure.
2 Cam Lock Nut x 2
3 Dowel x 2
Hardware Used:
H
2
D
I
13Insert Dowels 3 into the 4 indicated holes on the
underside of Bottom Shelf E. Fit the top edge of the
Caiet Side I onto the hardware on the bottom of
Shelf D.
Fasten the panels together by inserting a Cam Lock
Nut 2 (with arrow pointed toward the top) into the
hole adjoining each Cam Bolt, then turning the Cam
Lock Nuts clockwise until secure.
3 Dowel x 4
5 Screw mm x 4
Hardware Used: E
F
F
3
5
5
5
5
3
3
3
14 Insert Dowels 3 into the 2 indicated holes on the
bottom edge of Caiet Side I. Fit the top of the
Bottom Shelf E onto the Dowels.
Secure the Shelf to the Caiet Side by inserting 2
Screws 4 through the underside of the Shelf and
into the Caiet Side. Tighten using a Phillips-head
screwdriver.
3 Dowel x 2
4 Screw mm x 2
Hardware Used:
H
ID
E
3
4
4
Contact us for assistance: [phone] | www.balkenehome.com
7

ASSEMBLY
15Insert Cam Bolts 1 into the 4 indicated holes on
the Bottom Left Side L.
1 Cam Bolt x 4
Hardware Used: 1
L
1
1
1
3
3
3
3
3
L
F
F
H
D I
E
Hardware Used: 2 Cam Lock Nut x 4
3 Dowel x 12
Insert Dowels 3 into the 12 holes near the top, middle,
and bottom of Bottom Left Side L. Insert the Dowels and
Cam Bolts into corresponding holes in the left edges of
4th Shelf D and Bottom Shelf E.
Fasten the Side to the Shelves by inserting a Cam Lock
Nut 2 (with arrow pointed toward edge) into the hole
adjoining each Cam Bolt, then turning the Cam Lock Nuts
clockwise until secure.
Slide 2 Lower Shelf Supports F onto the 2 remaining
pairs of Dowels installed in Side L as shown.
16
17Insert Cam Bolts 1 into the 4 indicated holes on
the Bottom Right Side M.
1 Cam Bolt x 4
Hardware Used: M
1
1
1
1
Hardware Used: 2 Cam Lock Nut x 4
3 Dowel x 12
Insert Dowels 1 into the 12 holes near the top, middle,
and bottom of Bottom Right Side M. Insert the Dowels
and Cam Bolts into corresponding holes in the right
edges of the 4th Shelf D, Bottom Shelf E, and Lower
Shelf Supports F.
Slide the Lower Shelf Backer O into the grooves running
along the rear of the unit as shown. Push it all the way
into the groove running along the inside of Side L.
Fasten Side M to the Shelves by inserting a Cam Lock
Nut 2 (with arrow pointed toward edge) into the hole
adjoining each Cam Bolt, then turning the Cam Lock Nuts
clockwise until secure.
18
F
F
3
3
2
L
M
2
O
E
D
3
Contact us for assistance: [phone] | www.balkenehome.com
8
2
2

2 Backer Brace x 8
? Screw 3x16mm x 8
ASSEMBLY
Hardware Used: 2 Cam Lock Nut x 2
3 Dowel x 10
5 Screw 4x50mm x 8
? Foot Pad x 4
Use 10 Dowels 3 along the top surfaces of
the lower section, including the top of Divider
H to join it to the top section of the unit. Push
the two sections together firmly, being sure to
seat the 2 Cam Bolts 1 previously installed in
the bottom of 3rd Shelf C into the top of
Divider H.
To fasten the Cam Bolts, insert a Cam Lock
Nut 2 (with arrow pointed toward top) into
the hole adjoining each of hte 2 Cam Bolts,
then turn the Cam Lock Nuts clockwise until
secure.
To securely join the sections together, insert 8
Screws 5 through the holes in the top edges
of the lower section (front/back/sides) and
tighten firmly into the bottom of the upper
section using a Phillips-head screwdriver.
Peel the paper from the adhesive side of the
Foot Pads and press firmly onto each
corner of the bottom of the unit.
19
L
5
J
K
C
2
M
H
3
3
With assistance, carefully move the unit into
an upright position.
On the back of the unit, install the 8 Backer
Braces ? at each corner of the Backer panels
N/O. by sliding the small tab into the seam
between the Backer and the adjoining Side,
then securing with a Screw ?.
20
N
O
Hardware Used:
Contact us for assistance: [phone] | www.balkenehome.com
9

ASSEMBLY
Hardware Used: 7 Screw 4x12mm x 8
Attach the Handle 8 to the Door P using 2
Screws 9.
Flip the Door over to install the Hinges. Insert
the round hinge cup into the round bores near
the edge of the Door. Align the hinge eyelets
with the 2 small holes drilled adjacent to each
bore. Secure each Hinge by inserting 2 Screws
4x12mm through the eyelets and into the Door.
21
Hardware Used: 6 Hinge x 2
7 Screw 4x12mm x 4
8 Handle x 1
9 Screw 3x12mm x 2
Hang the Door P by attaching the Hinges 6 to
the inside right wall of the cabinet on the Bottom
Shelf. For each Hinge, insert 4 Screws 7 through
the eyelets of the hinge arm and into the holes on
the inside wall as shown.
22
P
9
9
P
7
7
8
6
6
P
7
7
If necessary for correct door alignment, it is possible to
adjust the hinges. See diagrams below:
abc
6
7
7
Contact us for assistance: [phone] | www.balkenehome.com
10