Balkene Home Tribeca 62760 User manual

Tribeca COLLECTION
BEDSIDE TABLE
Item#: 62760
Questions, problems, missing parts?
Before returning to your retailer, our exceptional customer service is available.
[phone] 9 a.m. - 9 p.m., EST
[email protected]
Call toll-free
Email
Live chat www.wtliving.com 9 a.m. - 4 p.m., EST, Monday - Friday
10292019
sAve these instructions
for future reference.
AttAch Your receiPt here
Keep a copy of your proof of purchase or order
conrmation which will be needed if you need to
contact us about warranty coverage.
Purchase Date:

Contact us for assistance: [phone] | www.wtliving.com 2
inforMaTion
before You beGin
Before beginning assembly, make sure all parts are present. Compare parts received with the “Parts List.” If any part
is missing or damaged, do NOT attempt to assemble the product. Please read and understand this entire manual
before attempting to assemble this product. If you have any questions regarding the product, please contact
Customer Service.
General inforMaTion
This item is made of hollow board and a metal frame. For safe assembly, set up on a dry, soft, secure and clean
surface. Do not clean with detergent or chemicals. Do not place hot items such as coffee cups directly on the
surface of this furniture item. Keep away from direct sunlight and water. Do not drag the table. For indoor use only.
safeTY inforMaTion
WARNING
DO NOT sit or stand or allow children to sit or stand on the assembled product. Make sure connectors are securely
in place. Perform periodic checks to make sure the connectors are secure and adjust if needed. Keep unassembled
parts and hardware away from children and infants. This package contains small parts and sharp points. Adult
assembly required.
CAUTION
READ all instructions before beginning assembly. Failure to do so may result in faulty assembly and potential injury.
Assemble the item on a soft, non-abrasive surface such as carpet or cardboard to avoid damaging the item.
Max safe load limit: Tabletop: 20 KG / 44 LB and Drawer: 5 KG / 11 LB.

Contact us for assistance: [phone] | www.wtliving.com 3
ParTs lisT
ParT descriPTion QuanTiTY
ALeg Frame 2
BTable Top 1
CTable Bottom 1
DTable Side (Right) 1
ETable Side (Left) 1
FTable Back 1
GDrawer Front 1
HDrawer Side (Right) 1
IDrawer Side (Left) 1
JDrawer Bottom 1
KDrawer Back 1
LDrawer Handle 1
M
Screw M7x48mm
Qty: 8
P
Screw M4x40mm
Qty: 4
S
Screw M4x30mm
Qty: 4
O
Cam Bolt
Qty: 6
R
Screw M4x20mm
Qty: 2
N
Cam Lock Nut
Qty: 6
Q
Dowel
Qty: 6
T
Hex Key
Qty: 1
hardWare conTenTs
A
B
C
D
E
F
G
H
I
J
K
L
YOU WILL NEED
FOR ASSEMBLY:
(not included)
Rubber Mallet
(If none is available, use a
hammer, but add padding as
necessary to protect parts and
surfaces.)
Phillips-head Screwdriver

Contact us for assistance: [phone] | www.wtliving.com 4
asseMblY
1Locate the Table Top B and place it so the side with drilled
holes face up. Insert and tighten 4 Cam Bolts O into the 4 holes
closest to the corners of the Table Top as shown. Insert 2
Dowels Q in the remaining 2 holes midway down the shorter
sides, as shown. Be sure the Dowels are firmly inserted by
gently tapping with a rubber mallet.
Locate the Drawer Front G and place it so the side with drilled
holes face up. Insert and tighten 2 Cam Bolts in the holes near
the middle of each short edge as shown. Set aside.
2Locate the Table Sides D/E and insert 4 Cam Lock Nuts N
into the holes below the pre-installed drawer track on each
piece. Turn Cam Lock Nuts so the arrow points toward the
adjoining hole drilled in the bottom edge.
Align the groove in Table Side (Right) D perpendicularly to
the groove in the Table Top and slide the Table Side onto the
hardware installed earlier, as shown. Secure the Table Side to
the Table Top by turning the Cam Lock Nuts clockwise until
tight.
Repeat to install the Table Side (Left) E.
Insert a Dowel Q into the hole drilled in the center of the top
edge of each Table Side. Be sure the Dowels are firmly
inserted by gently tapping with a rubber mallet.
3Slide the Table Back F into the groove formed by the Table
Sides D/E and Table Top B as shown. Make sure it is
securely and squarely seated in the bottom of the groove.
O
DE
B
G
Q
F
M
Q
E
B
D
O
O
O
O
O
Hardware Used: O Cam Bolt x 6
Q Dowel x 2
Q
Q
N
N
N
N
Hardware Used: N Cam Lock Nut x 4
Q Dowel x 2
D
E
B
PREPARATION
Before beginning assembly, be sure to empty contents of carton and make sure all parts are present. If any parts are missing,
please contact Customer Service before proceeding.
Place all parts on a soft, level surface for assembly. You will need a Rubber Mallet and¿Phillipsg>_ screwdriver for assembly.
Estimated Assembly Time: Ã0 Minutes | DO NOT over-tighten hardware!

Contact us for assistance: [phone] | www.wtliving.com 5
asseMblY
4Locate Table Bottom C. Position so holes in Table Bottom
align with holes in edges of Table Sides and corners are flush
and previously-installed Dowels are inserted into the middle
hole on each side of the inside of the Table Bottom.
Insert 4 Screws P through the 4 holes drilled in the Table
Bottom and into the holes drilled in the Table Sides. Tighten
with a screwdriver. Do not overtighten.
5Install the first Leg Frame A by finding the holes drilled
near one end and aligning them with the holes drilled in
the Table Top B and Table Bottom C. Insert 4 Screws M
through the Leg Frame and into the Table Top and Table
Bottom. Tighten using the Hex Key T.
Repeat to install the second Leg Frame.
Carefully turn the unit upright.
6
Assemble the drawer: locate Drawer Sides H/I and Drawer Back K.
With the drawer runner on Drawer Side I facing out and the
grooves on both pieces aligned on the inside, connect Drawer Side
to Drawer Back using 2 Screws S as shown. Tighten using a
screwdriver.
Repeat to connect Drawer Side H to Drawer Back.
Slide the Drawer Bottom J into the groove formed by the Drawer
Sides H/I and Drawer Back K as shown. Make sure it is securely
and squarely seated in the groove.
P
C
A
A
M
J
S
H
K
I
S
P
P
P
MM
M
M
M
M
M
B
Hardware Used: P Screw (M4x40mm) x4
Hardware Used: M Screw (M7x48mm) x8
Hardware Used: S Screw (M4x30mm) x4

Contact us for assistance: [phone] | www.wtliving.com 6
asseMblY
7Locate Drawer Front G and lay flat so the side with 6 holes faces up. Insert
Cam Bolts O into the upper hole along each short side and tighten with a
screwdriver. Insert Dowels Q into the 2 holes just below the Cam Bolts. Be
sure the Dowels are firmly inserted by gently tapping with a rubber mallet.
Attach the Drawer Handle L using two Screws R as shown.
Insert Cam Lock Nuts N in the hole above the drawer runner on each
Drawer Side. Turn so the small arrow points toward the adjoining hole in the
edge of the Drawer Side.
Insert the Cam Bolts and Dowels on the Drawer Front into the holes drilled
in the edge of each Drawer Side. Turn the Cam Lock Nuts clockwise with a
screwdriver to tighten.
9If needed, the drawer can be removed (e.g. for cleaning). Open the
drawer all the way, then lift and press the levers on both drawer
tracks at the same time to pull the drawer all the way out.
Ensure the drawer runners are aligned.
Lift/press the levers to remove the drawer.
NQ
R
Q
L
Hardware Used: N Cam Lock Nut x2
O Cam Bolt x2
Q Dowel x2
R Screw (M4x20mm) x2
8Install the drawer by aligning the drawer runners with the
drawer tracks as shown and pushing all the way in to
attach the runners to the tracks.
Your Tribeca Collection Bedside Table is ready for use!
O
O

LIMITED WARRANTY
Customers in the Contiguous US
This product is warranted for a period of 1 year from original purchase date
against defects in materials and workmanship under normal use. This
warranty does NOT cover normal wear/weathering, exposure to water,
freezing temperatures, oils, fluids, or chemicals OR use in a commercial
context if the unit is not designated as a commercial model. At Well Traveled
Living’s sole discretion, products under warranty will be repaired and/or
replaced at no charge to the customer. Returns sent back to Well Traveled
Living must be sent via prepaid freight in the original retail packaging.
For warranty service, contact Well Traveled Living at the address, phone
numbers or website and email listed in this owner’s manual. Be sure to have
your sales receipt, date of purchase and catalogue/model numbers available
when calling. All warranty service will be coordinated by Well Traveled
Living’s, Amelia Island, Florida service center. This warranty is extended only
to the original owner. Proof of purchase will be required before warranty
service is rendered. The sales receipt is the only valid proof of purchase. This
warranty only covers failures due to defects in materials or workmanship
which occur during normal use. Failures and/or damage which result from
accident, negligence, misuse, abuse, neglect, mishandling, alteration or
modification, failure to maintain, improper assembly or maintenance, service
by unauthorized agency or use of unauthorized components or damage that is
attributable to acts of God are NOT covered.
This limited warranty gives you specific legal rights and you may also have
other rights which vary from jurisdiction to jurisdiction. The provisions of the
United Nations Convention on Contracts for the Sales of Goods shall not apply
to this limited warranty or the sale of products covered by this limited
warranty.
• THERE ARE NO EXPRESS WARRANTIES EXCEPT AS
LISTED.
• PURCHASER ASSUMES ALL RISKS IN THE
ASSEMBLY AND OPERATION OF THIS UNIT.
• FAILURE TO FOLLOW WARNINGS AND
OPERATIONAL INSTRUCTIONS CONTAINED IN
THIS MANUAL CAN RESULT IN SEVERE PROPERTY
DAMAGE AND/OR PERSONAL INJURY.
• IN NO EVENT WILL WELL TRAVELED LIVING, OR
ITS DIRECTORS, OFFICERS OR AGENTS BE LIABLE
TO THE PURCHASER OR ANY THIRD PARTY,
WHETHER IN CONTRACT, IN TORT, OR ON ANY
OTHER BASIS, FOR ANY INDIRECT, SPECIAL,
PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR
INCIDENTAL LOSS, COST, OR DAMAGE ARISING
OUT OF OR IN CONNECTION WITH THE SALE,
MAINTENANCE, USE, OR INABILITY TO USE THE
PRODUCT, EVEN IF WELL TRAVELED LIVING OR
ITS DIRECTORS, OFFICERS OR AGENTS HAVE BEEN
ADVISED OF THE POSSIBILITY OF SUCH LOSSES,
COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS,
OR DAMAGES ARE FORESEEABLE. IN NO EVENT
WILL WELL TRAVELED LIVING, OR ITS OFFICERS,
DIRECTORS, OR AGENTS BE LIABLE FOR ANY
DIRECT LOSSES, COSTS OR DAMAGES THAT
EXCEED THE PURCHASE PRICE OF THE PRODUCT.
• SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO
THE PURCHASER.
Important Notice
Do NOT return to place of purchase—for customer service and warranty issues:
Call toll-free [phone] 9 a.m. – 9 p.m., EST
Email [email protected]
Live chat www.wtliving.com 9 a.m. - 4 p.m., EST, Monday - Friday
Distributed by:
Well Traveled Living
716 S 8th Street, Amelia Island, FL 32034
wtliving.com | [e-mail]
[phone]
Fire Sense®, Patio Sense,® Avalon Home,® Mojave Sun®, Vulcan®, Balkene Home® and Well Traveled Living® are registered trademarks of
Well Traveled Imports, Inc®. All assembly instruction presentations are the property of Well Traveled Imports, Inc.
® and are protected by
U.S. copyrights and trademarks. All rights reserved.
EXTEND YOUR WARRANTY
When you purchase a Fire Sense or Balkene Home product, you'll have peace of mind in
knowing that it comes with a one-year warranty. Extend your warranty for an additional year
when you write a review of your purchase on www.wtliving.com within 365 days of purchase.