Bante Instruments ORPscan10 User manual

ORPscan10/20 Pocket ORP Tester
USER MANUAL
Bante Instruments Inc.

1 IORPscan10/20
Overview
Thank you for selecting the ORPscan series pocket ORP tester. This user
manual provides a step-by-step guide to help you operate the tester,
please carefully read the following instructions before use.
Installing the Batteries
1. Twist the electrode collar counter clockwise, pull the electrode (or
BNC connector) away from the tester.
2. Insert two AAA alkaline batteries into the battery compartment,
note polarity.
3. Push the electrode (or BNC connector) into the tester and twist the
electrode collar clockwise until tight.
Keypad
Key
Function
•Switch the tester on or off
•Lock or unlock measurement
•Exit the calibration, settings and return to the ORP
measurement
•Start calibration
•Press and hold the key to enter the setup menu
•Select an option
•Confirm the calibration, settings or displayed option
Display
Icon
Description
When the battery voltage falls below the minimum
power requirements, the icon automatically
disappears
MEAS
Indicates that the tester is in the measurement mode
CAL
Indicates that the tester is in the calibration mode
SETUP
Indicates that the tester is in the setup mode
Prior to Use
ORPscan10
Remove the protective cap (and translucent cover) from the bottom of
the tester. If some salt crystals deposited on the electrode, rinse with
tap water to clean these deposits. If the platinum sensor has dried
out, soak the electrode in 4M KCl solution for about 30 minutes.
ORPscan20
Take out the ORP electrode from carrying case. Insert the BNC connector
into the connector socket on tester, rotate and push the connector
clockwise until it locks.
Switching the Tester On and Off
•Press and hold the Meas key for about 5 seconds to switch on the
tester.
•Press and hold the Meas key to switch off the tester.
If you do not press any key within 8 minutes, the tester will switch off
automatically to conserve energy.
4M KCl solution

ORPscan10/20 I2
Setup Menu
The ORPscan10/20 tester contains 3 menu items in the setup menu,
the following table describes the functions of each option.
Menu Item
Option and Description
Auto-Hold
If enabled, the tester will automatically sense and
lock the measurement endpoint.
Enable
Disable (default)
Auto-Power Off
If enabled, the tester will automatically switch off
if no key is pressed within 8 minutes.
Enable (default)
Disable
Factory Reset
If enabled, all of the calibration values and current
settings will be deleted or reset to the factory
defaults.
Enable
Disable (default)
Setting the Default Option
1. In the measurement mode, press and hold the Cal key to enter the
setup menu.
2. If necessary, press the Cal key again to select an option.
3. Press the Enter key, the tester saves the current option and moves
to the next menu item.
4. Repeat steps above until the tester returns to the measurement
mode.
To exit the setup menu, press the Meas key.
Measurement
Rinse the electrode with distilled water, place the electrode into the
sample solution and stir gently. Note, DO NOT completely immerse
the tester in water. Wait for the measurement to stabilize and record
the reading.
•The platinum sensor may give unstable readings in solutions that
contain chromous, vanadous and titanous ions or other ions that
are stronger reducing agents than hydrogen or platinum.
•If the display shows ---- indicating the measurement exceeds the
range, remove the tester from the sample immediately.
•If the option is enabled in the setup menu, the tester will
automatically lock the measurement endpoint and show HOLD
icon. Press the Meas key to resume measuring.
Option
Menu item

3 IORPscan10/20
Relative mV Calibration
The ORPscan10/20 tester allows 1 point calibration, but calibration is
not necessary unless exact readout agreement with a work standard
and at a specific ORP value is needed.
1. Rinse the electrode with distilled water and place into the standard
solution. Stir the tester (or electrode) gently and wait until the
measurement is stable.
2. Press the Cal key, the display shows 000/CAL.
3. Press the Cal key again to modify the calibration value, press the
Enter key to confirm and move to the next digit. When the setting
is completed, make sure that the displayed value matches your
calibration standard.
4. Press the Enter key, the tester begins the calibration. When the
reading has stabilized, the display will show .
•After the calibration, the measurement unit "mV" will automatically
convert to "R.mV" (relative millivolt). If you want to resume the mV
measurement, reset the tester (refer to the Setup Menu section).
•To exit the calibration without saving calibrated value, press the
Meas key.
Electrode Maintenance
•Rinse the electrode thoroughly with distilled water after use.
•In the corrosive chemicals, viscous solutions and solutions with
heavy metals or proteins, take readings quickly and rinse electrode
immediately.
•If you do not use the tester for a period longer than 1 month, store
the electrode in 4M KCl solution or electrode storage solution.
Appendix
Preparation of ORP Standard Solutions
Quinhydrone solution A:
Dissolve 3 grams of quinhydrone reagent in 500 ml of the pH 4.01
buffer solution, stir the solution for about 10 minutes. Undissolved
quinhydrone reagent must be present. If necessary, add the reagent.
Temperature
Quinhydrone in pH 7.00 (± 10 mV)
20°C(68° F)
94 mV
25°C(77° F)
87 mV
30°C(86° F)
80 mV
Quinhydrone solution B:
Dissolve 3 grams of quinhydrone reagent in 500 ml of the pH 7.00
buffer solution, stir the solution for about 10 minutes. Undissolved
quinhydrone reagent must be present. If necessary, add the reagent.
Temperature
Quinhydrone in pH 4.01 (± 10 mV)
20°C(68° F)
268 mV
25°C(77° F)
263 mV
30°C(86° F)
260 mV
Due to the quinhydrone solution is susceptible to air oxidation in
storage, make sure to prepare the fresh solution before use.
Preparation of Electrode Storage Solution
Dissolve 29.82 grams of analytical grade KCl reagent in 100 ml distilled
water. Add pH 4.01 standard buffer and adjust solution to pH 4.
Optional Accessories
Solutions
Order Code
Description
PHCS-ES
Electrode storage solution, 480 ml

ORPscan10/20 I4
ORP Electrodes
Order Code and Description
E-ORPscan-S
•General purpose ORP electrode, platinum
sheet
•For measuring the general water samples
E-ORPscan-BNC
•BNC connector for ORPscan series testers
501
•General purpose ORP electrode, platinum
pin, epoxy body, 12 mm (0.47 in.) diameter
•For measuring the general water samples
504
•General purpose ORP electrode, platinum
ring, glass body, 12 mm (0.47 in.) diameter
•For measuring the high temperature
samples (< 100° C/212° F)
Tester Specifications
Model
ORPscan10
mV Range
± 999 mV
Relative mV Range
± 999 mV
Resolution
1 mV
Accuracy
± 2 mV
Calibration Point
1 point
Operating Temperature
0 to 50° C (32 to 122° F)
Storage Temperature
0 to 60° C (32 to 140° F)
Relative Humidity
< 80% (non-condensing)
IP Rating
IP54
Connector
---
Display
LCD, 21 ×21 mm (0.82 ×0.82 in.)
Power Requirements
2×1.5V AAA alkaline batteries
Auto-Off
8 minutes after last key pressed
Dimensions
185 (L) ×40 (Ø ) mm (7.28 ×1.57 in.)
Weight
100g (3.5 oz.)
Model
ORPscan20
mV Range
± 999 mV
Relative mV Range
± 999 mV
Resolution
1 mV
Accuracy
± 2 mV
Calibration Point
1 point
Operating Temperature
0 to 50° C (32 to 122° F)
Storage Temperature
0 to 60° C (32 to 140° F)
Relative Humidity
< 80% (non-condensing)
IP Rating
IP54
Connector
BNC
Display
LCD, 21 × 21 mm (0.82 × 0.82 in.)
Power Requirements
2 × 1.5V AAA alkaline batteries
Auto-Off
8 minutes after last key pressed
Dimensions
175 (L) × 40 (Ø ) mm (6.89 × 1.57 in.)
Weight
100g (3.5 oz.)

The information in this document is subject to change without notice.
Copyright © Bante Instruments Inc, 2022. All rights reserved.
Disposal
This product is required to comply with the European Union’s Waste
Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC and
may not be disposed of in domestic waste. Please dispose of product
in accordance with local regulations at the collecting point specified
for electrical and electronic equipment.
Warranty
The warranty period for tester is one year from the date of shipment.
Above warranty does not cover the electrode and standard solution.
Out of warranty products will be repaired on a charged basis.
The warranty on your tester shall not apply to defects resulting from:
•Improper or inadequate maintenance by customer
•Unauthorized modification or misuse
•Operation outside of the environment specifications of the
products.
For more information, please contact the supplier.
Office: 4715 Castlewood St., Sugar land, TX 77479, USA
Tel: [phone]
E-mail: [email protected]
Factory: F3, Building 2, No.2185, Laifang Rd., Shanghai 201615, China
Tel: [phone]
E-mail: [e-mail]
www.bante-china.com