Barco EC-30 User manual

Barco Technical Support:
USA:
EMEA:
China:
APAC:
Support:
Event Master Series EC-30
Quick Start Guide –Setup
[phone]
[phone]
40088 22726
[phone]
www.barco.com/en/support
Event Master Series Controller Installation: System Connections
P/N 60600356 Rev 00
System Setup
For detailed installation instructions, refer to the Event Master Devices User’s
Guide (R5905948).
Power Up and Status Check —Power up the EC-30 control panel,
Host computer, and peripherals.
Connections —Connect the Host computer to the USB B connector on
the EC-30. Necessary cables are provided in a new system. In the case
that the original cables are missing, simply use standard computer
cabling to make these connections.
System setup is comprised of sequences each of which includes
many steps.
For error-free setup, always refer to the associated sections in the
Event Master Devices User’s Guide (R5905948).
Communications Setup —During the Event Master Toolset installation
you are asked to add a driver, be sure to answer yes to this question in
order to use the EC-30 with your host computer. If the driver is not
installed the EC-30 will not work.
1
3
4
5Startup state of the desk —Once the desk is connected and started it will retrive the button assignment of the
configuration. If there is none it will have to be assigned.
EC-30 Rear Panel DC
Power
6Assigning resources to the desk —In the Event Master Toolset, click on the icon to open the controller menu
setup page. Drag and drop the resources from the right side onto the buttons corresponding to the ones on the console.
Power
Supply
Power Connection —Connect AC power to the power supply, and
connect the power supply to DC power on the rear panel of the unit.
2
Strain
Relief
Tab
Strain
Relief
Tab
If the Blue LEDs of the
Destination buttons
chase back and forth,
they indicate that the
communication with the
host controller is not
establisched.
Blue LED Indicators
in
Destinations
You can consume extra cable length, if necessary, by passing the cable through
both tabs.
Tip: Running the power-supply cable through one of the strain-relief tabs
on the rear of the unit can help to keep the cable from pulling out of the
DC power connector. Loosen the screw on a relief tab; run the power-
supply cable through the tab; tighten the screw.
USB B
to Host

BG 1
-
9
2
-
10
3
-
11
4
-
12
5
-
13
6
-
14
7
-
15
8
-
16
CUT All
Trans
Freeze
PVW
Freeze
PGM
Match
PGM
Arm
Page
1
Page
1
Destination
Layer
Assign
Layer
Trans
Layer
Cut
Event Master Series Controller Operation
P/N 60600356 Rev 00
Barco Technical Support:
USA:
EMEA:
China:
APAC:
Support:
Event Master Series EC-30
Quick Start Guide –Setup
[phone]
[phone]
40088 22726
[phone]
www.barco.com/en/support
For detailed installation instructions,
refer to the Event Master Devices
User’s Guide (R5905948).
LEDs
Operation overview
7
Layers —These buttons give direct selection of the
Layers in the selected Destinations. In normal mode
the button selects and/or adds a layer in the Preview
of the selected Destination. A green LED indicates
selected.
In LIVE mode (unlocked Program) the Layer is
selected in the Program of the selected Destination.
Destinations —These buttons give direct selection
of the assigned Destination configurations. Buttons
toggle on and off the selection. A blue LED indicates
selected.
Assign —These buttons give direct selection of the assigned resources. There are
several that can be mapped.
PRESETS —The Presets created in EMTS can be mapped onto a bus that is
selected to PRESETS.
USER KEYS —The User Keys created in EMTS can be mapped onto a bus that is
selected to USER KEYS, like the top row in the picture.
SOURCES —The Source Files, (not the Inputs) created in EMTS can be mapped
onto a bus that is selected to SOURCES, like the bottom row in the picture.
BACKGROUND SOURCES —The Backgrounds created in EMTS can be mapped
onto a bus that is selected to BackGround Source, this is not shown in the picture.
Once a Button is assigned with a resource, the backlight of the display will turn to the
corresponding color.
Arrow buttons —These buttons choose the next page of its button bus.
Contextual Display Buttons —These provide mapping of a variety of
functions from the EMTS.
Mapping of them is done in the menu.
8
910
11
13
14
Layer Function Buttons —These buttons provide indicated function to
selected Layer(s).
Cut & All Trans —These buttons execute the transition setup in the GUI.
12
T-Bar —Manually transitions Preview to Program.
Blue indicate
selected or active in
all its buttons
Green indicate
selected in Preview
Red indicate
selected in Program
or
Transitioning
Backlight
Once a Button is assigned with a
resource, the backlight of the
display will turn to the
corresponding color.
- White for Presets
- Magenta for User Keys
- Yellow for Source Files
- Green for Background Sources
10
11 12
14
13 13 13
7
8
9
Source
1
User
Key
1
10
10
10