Barco R9841550 User manual

BARCO PROJECTION
UNIVERSAL LAMP KIT FOR 6000 SERIES LCD
PROJECTORS
R9841550
INSTALLATION MANUAL
15032002 R5976452/01

Barco nv Intelligent Displays
Noordlaan 5, 8520 Kuurne
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium

Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufactures.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of BARCO.

Revision Sheet
To:
Barco nv Intelligent Displays
Noordlaan 5, 8520 Kuurne
Phone: [phone], Fax: [phone]
E-mail: [email protected], Web: www.barco.com
From:
Date:
Please correct the following points in this documentation (R5976452/01):
page wrong correct
R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002

1. Safety
1. SAFETY
1.1 Safety
Safety Warnings
The procedures in this manual are intended for use only by qualified service technicians who have been trained and authorized by
BARCO !
Switch the projector to stand by and let it cool down for at least 15 minutes before starting with the lamp replacement. These lamps
consist of a quartz arc tube operating at very high temperature and high pressure which may explode suddenly. There is a risk of
personal injury and property damage from hot quartz arc tube particles if handled incorrectly.
Power down the projector and unplug the power cord from the wall outlet. Once the projector is cooled down and the power is off,
continue with the replacement procedure.
Do not exceed the indicated maximum total lifetime of the lamp for safe operation in normal power mode. Do not use it longer !
Always replace the lamp with the BARCO lamp kit for 6500 projectors.
R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002 1

1. Safety
2R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002

2. Kit content
2. KIT CONTENT
2.1 Purpose of the Kit
Universal Lamp Kit
The lamp is designed to be used in two different configurations of the projector
• table mount
• ceiling mount
The mechanical design allows to shift the lamp unit by means of two adjustments, hereby insuring the best optical performances of
the lamp in both projector configurations.
This kit is designed for the 6500(R+G), 6400i and SIM6(HB) projectors.
2.2PartslistoftheKit
Partslist overview
Depending on the Kit ordered,
R9841550 single lamp
R98415501 12 pack
R98415502 60 pack
following parts will be included
Partnumber Partname Quantity
R8223342 lamp(s) 1or12or60
R5976452 Installation Manual 1
Each new lamp is marked with a serial number (6 digits). Write down this number in the foreseen area. The
serial number has to be programmed when resetting the lamp run time.
0
R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002 3

2. Kit content
2.3 Illustration of the Lamp
Universal lamp
Image 2-1
4R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002

3. Access to the lamp unit
3. ACCESS TO THE LAMP UNIT
3.1 Removing the protection cover
What has to be done ?
• The lamp house door has to be opened and removed.
• The lamp protection cover has to be removed.
Make sure that the projector is turned off ! Never open the lamp house when the projector is on!
Necessary tools
flat screwdriver of 5 mm
How to remove the lamp door ?
1. Turn with a screwdriver the door lock screw a quarter turn counter clockwise. (image 3-1)
2. Open the door a little.
3. Unhook the door from its fixing points. (image 3-2)
Image 3-1
R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002 5

3. Access to the lamp unit
Image 3-2
How to remove the protection cover
1. Loosen with a screwdriver the 3 indicated bolts. (image 3-3)
2. Pivote the plate a little downwards. (image 3-4)
3. Take out the protection cover.
Image 3-3
Image 3-4
Hot surface !
Do not touch the fan blades.
High pressure lamp may explode if improperly handled. Refer servicing to qualified service personnel.
6R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002

4. Removing the old lamp unit
4. REMOVING THE OLD LAMP UNIT
4.1 Extracting the lamp unit
Necessary tools
No tools.
How to remove the lamp unit ?
1. Slide the lamp unit backwards. (image 4-1)
2. Take out the lamp unit and put it on the table. (image 4-2)
3. Take the sides of the lamp connector between thumb and finger
4. Unlock the connector by pushing at the same time on both lock parts and separate the connectors. (image 4-3)
Image 4-1
Image 4-2
Image 4-3
The length of the lamp power cables may differ depending on the lamp type. In case of a lamp with a shorter
cable than that shown on the images then first unplug the connector since extracting the lamp first will be
difficult due to the short cable.
R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002 7

4. Removing the old lamp unit
8R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002

5. Installing the lamp unit
5. INSTALLING THE LAMP UNIT
5.1 Installing
What has to be done ?
a) the lamp has to be adjusted according to the mounting configuration of the projector
b) the lamp has to be placed in the projector housing and has to be connected
Do not touch the front lamp glass with your fingers since this can reduce the light output of the lamp !
If the glass is touched, finger prints can be removed by cleaning the lamp with alcohol.
Necessary tools
• flat screwdriver 5mm
• Phillips screwdriver 3mm
Adjusting the lamp
1. Place the metallic plate as shown on the figures depending on the mounting configuration. (image 5-1, image 5-2)
To place the lamp in the table position, slide the metallic plate as shown on the following figure (image 5-3)
2. Adjust the lamp by loosening the 2 screws (2 arrows on image) and placing the lamp according to the desired configuration ( see
screening on lamp). (image 5-4, image 5-5)
3. Tighten the 2 screws to secure the position.
Image 5-1
Image 5-2
A Ceiling Mount configuration
B Table Mount configuration
R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002 9

5. Installing the lamp unit
Image 5-3
Switching from CM (Ceiling Mount) to TM (Table Mount)
Image 5-4
Image 5-5
A Ceiling Mount configuration
B Table Mount configuration
Placing and connecting the lamp
1. Place the lamp in the housing (as shown on the image).
2. Connect the connector at the lamp side into the connector at the power side. (image 5-6)
3. Slide the lamp unit in the lamp house until the ref. holes in the bottom part of the lamp unit matches the ref. pins on the projector
frame. Push the lamp power cable on its place as shown on the image. (image 5-7)
Image 5-6
10 R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002

5. Installing the lamp unit
Image 5-7
A reference holes
R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002 11

5. Installing the lamp unit
12 R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002

6. Closing the lamp house
6. CLOSING THE LAMP HOUSE
6.1 Mounting the covers
Necessary tools
flat screwdriver of 5 mm
Mounting the protection cover
1. Put the protection cover on its place. (image 6-1)
Warning: Warning : be careful for the lamp power cable. Do not stick this cable between the protection cover and the lamp
house
2. Secure the position of the cover with the 3 indicated bolts. (image 6-2)
Image 6-1
Image 6-2
Closing the lamp house door
1. Hook the door on its fixing points. (image 6-3)
2. Close the door.
3. Turn with a screwdriver the door lock screw a quarter turn clockwise. (image 6-4)
R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002 13

6. Closing the lamp house
Image 6-3
Image 6-4
14 R5976452 UNIVERSAL LAMP KIT FOR 6000 SERIES LCD PROJECTORS 15032002