Bartec TECHRITEPRO TPMS User manual

On/Off & Quick Menu Key:
Back & Home:
Enter & Test Key:
Used to power on and off the
device, and allows you to access
a quick menu toolkit wherever the
3 bars are lit.
Allows you to single press to go
back, or press and hold to return to the home menu.
Pressing enter allows you to
continue to the next screen or press test to test.
Technical Support Hotline
[phone]
R-PRT-624
Rev. 1.2 6/8/2021
Copyright 2021 - All Rights Reserved
BARTEC TECHNICAL
SUPPORT:
TOLL FREE: [866]407-8767
E-Mail: [email protected]
GETTING STARTED USING YOUR TECHRITEPRO:
1)
2)
3)
4)
5)
Follow On-Screen Setup Instructions
Download and install TPMS Desktop
Register your tool
Update your tool to the latest software
Fully charge your tool [best if done overnight]
TECHRITEPRO
Quick Start Guide
Your TECHRITEPRO
TPMS Tool comes
with a field
replaceable battery
and a “plug in” style
charging adapter.
See digital user guide
for detailed battery
replacement instructions.
Replaceable Battery Part Number: WRTTRPBAT
Tool Charging:
Before Using your Tool: Tool Registration and
TPMS DESKTOP:
IMPORTANT: The TECHRITEPRO
must be registered to get access to:
- Latest Tool Software Updates
- TPMS Support and Resource Information
To create your Bartec account and/or register your
tool, please download the TPMS DESKTOP
application from . TPMS
Desktop will register your tool and download the
latest updates to your tool when updates become
available. TPMS Desktop will help you manage
audit reports, TPMS info and access training and
technical service bulletins.
Unable to use TPMS Desktop? Register your tool
at and contact Bartec Tech
Support for assistance.
MODEL: TECHRITEPRO
www.tpmsdesktop.us
www.bartecusa.com
TPMS Relearn:
TPMS Relearns are the method used to reset or
“re-sync” the TPMS system. Bartec recommends
to ALWAYS complete the TPMS Relearn following
any service. Please note: vehicle may need to be
driven up to 20 minutes for the system to
recalibrate.
Key Functions:
Tool Layout:
Congratulations on purchasing North America’s newest TPMS
Service Tool! Please take time and review this Quick Start Guide,
and the digital User Guide found at www.bartecusa.com. The
following information is useful when calling Bartec about your tool.
Keep this Quick Start Guide with the tool for future reference.
On/Off
Quick
Menu
Down
Arrow
Left
Arrow
Right
Arrow
Color
Display
Back
Home
Enter
Test
(Activate
Sensors)
Up
Arrow
USE OF A NON APPROVED REPLACEMENT
BATTERY VOIDS TOOL WARRANTY
TPMS Desktop is REQUIRED
to REGISTER, UPDATE and
USE the TECHRITEPRO!
R-PRT-624 1.2
Tuesday, July 06, 2021 10:56:10 AM

Test Sensors:
Test Sensors - The TPMS Health Check!
Following the on screen prompts the tool will guide
you through getting the status of the TPMS
Sensors.
®
RITE-ID can be used to identify aftermarket
sensors. The TECHRITEPRO will search for:
® ® ®
RITE-SENSOR , Ez-Sensor ,Intellisens and Redi
® ® ®
Sensor , Sensit and Hamaton Sensor.
®
RITE-SYNC :
®
RITE-SYNC combines sensor programming and vehicle relearn all in one step. This process makes the
® ®
job easier, faster and more accurate. If programming the RITE-SENSOR rather than using RITE-SYNC
the will program in less then 3 seconds.
®
RITE-SENSOR
Scan the QR to
watch a video
R-PRT-624
Rev. 1.2 6/8/2021
Copyright 2021 - All Rights Reserved
Technical Support Hotline
[phone]
®
RITE-ID (Sensor Search):
TECHRITEPRO
Quick Start Guide
Sensor Programming (Aftermarket):Tool Positioning:
Banded Sensors
Ford used Banded
sensors from 2006-
2011 (and later on
the Crown Victoria).
These sensors are
mounted on a band in
the drop center of the
wheel and should be
180 degrees opposite
the valve stem. If you
are not getting a reading, reposition the tool a
few degrees left or right as the senor may have
rotated in the wheel.
Valve Stem Mounted Sensors Please review below
to ensure you are using the proper positioning. For
more information,
please download and
refer to your user
guide. For valve stem
mounted sensors, the
tool should be
located on the tire
side wall pointing at
the sensor as shown.
Access this menu for Aftermarket Sensor
®
Programming (Not RITE-SYNC ). To View a list of
currently covered Aftermarket Sensors please visit
software update TSB.bartecusa.com
Continue to RITE-
®
SYNC process until
completed.
R-PRT-624 1.2
Tuesday, July 06, 2021 10:56:11 AM