BBC Bircher XRF-TI User manual

1
XRF-TI
LED
18
194
174
190
4.54.5
18


Transmitter to XRF wireless transmission system
Original operating instructions
Intended use: Monitoring safety edges on doors and gates, in combination with a receiver XRF
ENGLISH
404301E
01/21
 Carefully pull out
the PCB
 Loosen screw
(at original delivery
shipped in bag with
Philips screw driver #00)
 Plug in connector
 Pairing (1.2) if required
 Slide in the PCB again
 Close the housing, tighten the screw (Philips #00, shipped with unit)
 LED ashes 5x (conrms battery connected)
Delivery state Battery connected
1.1 Connect battery
1Set-up
Battery 3.6. VButton
Screw
Button
Note:
Position of
red wire
Note:
Alignment of battery,
position of wire
PCB
Cable
with
plug
Wire
Saftey instructions
• Read these operating instructions thoroughly before putting the device into
operation and keep them for future reference.
• Do not use this product other than for its specied application.
• Only trained and qualied personnel may install and initialize the device.
• Only authorized factory personnel may perform hardware/software changes or
repairs to the product.
• Failure to follow these safety precautions may cause damage to sensor or objects,
serious personal injury, or death.
• It is the responsibility of the equipment manufacturer to carry out a risk assess-
ment and to install the system, in compliance with applicable local, national and
international regulations, safety standards, codes and laws as well as the
Machinery Directive 2006/42/EC, should this apply.
• Always consider the safety functions of your applications as a whole, never just in
relation to one individual section of the system.
• The installer is responsible for testing the system to ensure it meets all applicable
safety standards.
• Safety devices that are classied as Category 2 according to EN ISO 13849-1 must
be tested regularly – at least once per cycle.
• If the safety device is not requested operationally at least once a year, it must be
checked manually by the operator at least once a year.
• Pay attention to all local relevant electrical safety regulations.
• Protect the device with a housing against contamination or aggressive environ-
ments.
• This device contains batteries.
• Observe the local regulations for battery disposal.
• After accessing the inside of the sensor, ensure the cover/protection seal is
closed tightly to achieve designated protection rating.

2
OK?
3x
Designed in Switzerland / Made in China
BBC Bircher Smart Access, BBC Bircher AG, Wiesengasse 20, CH-8222 Beringen, www.bircher.com
OK?
XRF-TI
2x
Slide in the PCB
Close the cover again
System test mandatory!
Dispose battery acc. to local regulations
 Order new battery (prepared with connector)
Pull out the PCB (see 1.1.)
 Disconnect battery plug and remove battery
 Insert new battery, plug in connector
2Trouble shooting
2.1 Warning indicator for low battery voltage
1.4 System check (mandatory after each set-up)
2.2 Battery change
Check the system
by pressing the safety edge
Every minute
Receiver
Beep
3Technical data
Transmittter
Input 8.2 kOhm sensor
Battery power 1x Lithium Inorganic 3.6 V
Battery life up to 7 years
Protection class IEC 60529 IP65
4EU Declaration of Conformity
6Contact
5WEEE
Devices with this symbol must be treated separately during
disposal. This must be done in accordance with the laws of the
respective countries for environmentally sound disposal, proces-
sing and recycling of electrical and electronic equipment.
XRF-TI is designed for the concealed installation in
the contact proles of ExpertSystem (see assembly
and mounting instruction).
However it can be wired with other saftey edges
eg. where space is limitted.
The LED ashes when activating the sensor element (pressing the sensing edge)
and ashes again when releasing the sensor element.
Does the door/gate stop when the sensing element is activated?
1.3 Mounting
Sensing
edge
Built-in
(e.g. sliding gate)
Surface mount
(e.g. industrial door with ClickLine)
To nd out which
transmitter has low
battery: Press each edge.
Battery good Battery bad
Beep
Sensing edge
XL
Pairing is possible with open transmitter or later in mounted situation.
After initiating pairing on Rx
(see receiver manual),
press button
After initiating pairing on Rx (see receiver manual),
press the edge two times within 2 sec.
1.2.a Pairing at open state 1.2.b Pairing at built-in state
1.2 Pairing
See attachment
System
Operating frequency 868.3 MHz
Range 100 m (at optimal condition)
Operating temperature –20 °C to +60 °C