BCP SKY2788 User manual

SKY2788 + SKY3688 + SKY4744 + SKY6257
Ver. 5
INSTRUCTION
MANUAL
Modern Coee Table with Lift-Top

The following safety hazards may result in serious injury
or death:
• Firmly secure all bolts, screws and knobs before use.
• Reconfirm that all bolts, screws, and knobs are secure
every 90 days.
• Do not use or store this item in the proximity of open
flame or flammable/combustible chemicals.
• Always lay components on a clean, soft-cushioned surface during assembly.
• Improper installation may cause damage to the product.
• Product is intended for indoor use only.
• If any parts are missing, broken, damaged, or worn, stop using this item until repairs are made and/or
factory replacement parts are installed.
• Do not use this item in a way inconsistent with the manufacturer’s instructions as this could void the
product warranty.
• To wipe down the furniture, use a damp cloth. Then, wipe it down once more with a dry cloth.
• Be aware that extra hardware may be included.
TOOLS REQUIRED
HARDWARE
PHILLIPS
SCREWDRIVER
ELECTRIC DRILL
WITH PHILLIPS BIT
FLAT HEAD
SCREWDRIVER
2|
WRENCH
(PROVIDED)
HAMMER
NOTICE
A
32 PCS
DOWEL CAM BOLT
B
36 PCS
CAM LOCK
C
36 PCS
CAM COVER
D
36 PCS
E
6 PCS
TABLETOP
PAD
SCREW I
F
28 PCS
SCREW II
H
8 PCS
FOOTER
I
4 PCS
APPROXIMATELY
45 MIN.
45LY
1 PERSON
ASSEMBLY UP TO 45 MIN.
ASSEMBLY
1 PERSON
ASSEMBLY
100 LBS
CAPACITY
LBS

| 3
4
2 PCS
SIDE PANEL
PARTS
1 PC
TABLETOP
1
1 PC
END PANEL
2
1 PC
BOTTOM SHELF
6
5
1 PC
INNER SHELF
2 PCS
DIVIDER
3
10
1 PC
LIFT HINGE I
2 PCS
BASEBOARD
7
2 PCS
LEG I
8
1 PC
END PANEL II
12
11
1 PC
LIFT HINGE II
2 PCS
LEG II
9

Insert four part B cam bolts into each part
2 and part 12 end panel.
Insert two part B cam bolts into each part 4 side panel.
TOOLS REQUIREDPRODUCT ASSEMBLY
1
2
2
12
x4
B
x4
B
4|
Please retain these instructions for future reference.
4
x2
B
4
x2
B

Insert four part B cam bolts into part 5 inner shelf.
Insert five part B cam bolts and one part I footer into each part 8 and 9 legs.
TOOLS REQUIREDPRODUCT ASSEMBLY
3
4
5
x4
B
| 5
8
9
x5
B
x5
B
x2
x2
Use a hammer to secure
the footer.
I
I

Insert four part A dowels and four part C cam
locks into each part 2 and part 12 end panel.
Attach part 8 and 9 table legs to part 2 and
part 12 end panels.
Use drill to attach part 10 and part 11 lift hinges to part 1 tabletop with twelve part F screws.
Unscrew the nuts from each lift hinges with the provided wrench.
TOOLS REQUIREDPRODUCT ASSEMBLY
5
6
6|
9
98
8
122
10
11
1
Fx12
Use a screwdriver
to turn the cam lock to
secure the cam bolt.
C
x4
C
x4
Ax4 Ax4

Insert four part A dowels into part 6 bottom shelf.
Use drill to attach part 7 baseboards to part 6
bottom shelf with four part F screws.
Insert four part A dowels and four part C cam locks into
each part 3 end dividers.
Connect part 5 inner panels with two part 3 dividers. Use
drill to attach part 6 bottom shelf with four part H screws.
TOOLS REQUIREDPRODUCT ASSEMBLY
7
8
| 7
6
7
7
Hx4
Ax4
Use a screwdriver
to turn the cam lock to
secure the cam bolt.
6
x2
3
5
Hx4
Ax8
Cx8

Cx4
Ax4
6
5
4
4
Have the long size of the shelf vertically.
Insert four part A dowels and four part C cam locks
into part 5 inner shelf.
Attach two part 4 side panels into part 5 inner shelf.
TOOLS REQUIREDPRODUCT ASSEMBLY
9
8|
Use a screwdriver
to turn the cam lock to
secure the cam bolt.

TOOLS REQUIREDPRODUCT ASSEMBLY
11
| 9
Use a screwdriver
to turn the cam lock to
secure the cam bolt.
Insert four part A dowels and ten part C cam locks
into each sides of the shelf.
Attach part 2 and part 12 end panels to each sides of
the shelf.
A
x4
C
x10
A
x4
C
x10
6
6
12
2

Have the coee table standing on it’s legs.
Peel and place part E tabletop pads on the tops of each part 8 and 9 legs.
Then apply part D cam covers over each exposed cam lock.
TOOLS REQUIREDPRODUCT ASSEMBLY
12
9
8
8
D
Ex6
10 |