Beam DriveDOCKExtreme User manual

DriveDOCK Extreme
Quick Start Guide
BEAM Communications Pty Ltd
DriveDOCK Extreme Installation set up
•
www.beamcommunications.com
PART #: USRQSG007101
BEAM Communications Pty Ltd
8 Anzed Court, Mulgrave
Victoria, 3170, AUSTRALIA
Web: www.beamcommunications.com
Info: [email protected]
Support: [email protected]
Tel: [phone]
Fax: [phone]
GREEN
BROWN
BLUE
1
1
2
3
4
2
3
4
5
6
7
8
9
10
11
12
13
14
Latch button
Docking Latch
Feature buttons
Mini USB port
5Intelligent handset
7
8
9
10
STATUS indicator
Antenna Connector
GPS connector
Horn Alert / Audio
System Mute
11 Alert loop IN/OUT 14 Mic connector
6Privacy handset 12 DC power
GME
SPK07
13 Speaker connector
* Optional accessory (Alert button)* Optional accessory
* Optional accessory
DriveDOCK Extreme
PRESS
DriveDOCK Extreme
1
4
7
*
9
6
3
8
0
#
5
2
ABC
GHI JKL
MNO
PQRS TUV
+
[
WXYZ
a
A
DEF
PRESS
Intelligent Handset:
• Mountthehandsetcupinasuitableposition
• ConnecttheIntelligenthandsetRJ45connector
intotheRJ45socketatthebaseoftheDriveDOCK
Extreme
• Intelligenthandsetmodeisactivewheneverthe
handsetisremovedfromthecup
Options
Tracking & Alert
Tracking&alertrequirestheGPSantennaandsetupof
thetrackingand/oralertingmessagesinEagleandinthe
IridiumExtremeHandset.
External Alert Loop Button:
ConnectaNormally-CLOSEDbutton,totheBrownand
Greenwires(itcanbeextendedforlongerruns).
TheloopneedstobeOPEN(pressbutton)for2secondsto
activateAlert(SOS)mode.
Privacy Handset:
• Mountthehandsetcuptothemountingplate.
• Mountthespacerplateandthemountingbracket,by
usingthelongerscrewsprovidedwiththekit.(Re-
installedtheRAMarm-bracketbehindtheseplates).
• ConnectthePrivacyHandset3.5mmplugintothe
socketatthebaseoftheDriveDOCKExtreme
• PrivacyHandsetmodeisactivewheneverthe
handsetisremovedfromthecup.

1. At the base of the Iridium
Extreme handset there is an
accessory connector cover. Open
the cover and move it to the back
of the handset, securing it to the
two rear retaining features.
2. Press down the latch button and
then gently rotate it up to open
the latch.
3. Place the Iridium Extreme handset
into the DriveDOCK Extreme.
4. Lift the latch back over the handset
until it Click’s into place.
“CLICK”
1. To remove the handset, first
press the eject button and then
rotate the latch up away from
the handset. The handset can
now be slid up and out of the
DriveDOCK. Refit the accessory
connector cover to maintain the
IP rating of the Iridium Extreme
handset.
1. Attach one pivot base to the rear
of the DriveDOCK Extreme using
the M4 screws supplied.
2. Secure the second pivot base to
the location you have selected
for mounting the DriveDOCK
Extreme. (Screws not supplied)
3. Use the interconnecting arm of
the RAM® mount to secure the
DriveDOCK Extreme to the pivot
base and tighten into the desired
location rmly using the wing
nut on the arm.
Inserting and Ejecting Extreme Handset
Inserting: Removing:
Iridium Antenna Connection
The antenna connections exit from the rear of the
DriveDOCK Extreme cradle, via the antenna loom. There
are two RF connections required, the Satellite TNC
Female Connector and GPS SMA Female connector.
Refer to the antennas installation guide for antenna
mounting and location requirements.
WARNING
DO NOT pull with force on the cables from the rear of
the DriveDOCK. Please install strain relief clamping for
the antenna cables where required.
Correct installation of the antenna system is a vital
part of the DriveDOCK DRIVE system, to ensure reliable
functionality, and drop-free calls.
Mounting Cradle
The DriveDOCK Extreme is supplied with a universal RAM® mount bracket that enables mounting to any at surface
(vertical or horizontal) within a vehicle, or other required location.

DriveDOCK Extreme Front Panel
LOCATION BUTTON MODE ACTION LED/SOUND
Mute press
On/o
In a Call:
Mute the microphone (uplink) on the Hands-free,
optional privacy handset, or optional Intelligent
Handset
LED turns RED Muted
LED turns OFF
Not muted
OR
Up/Down In a Call:
Increase/decrease volume on the audio device in use
Audio will sound louder/quieter with each press.
Out of Call or Incoming Ring:
Increase/decrease volume of incoming ring tone on
the external or internal speaker. (The lowest setting will
silence the Ringer)
A beep will sound indicating the increased/decreased
ring tone volume of the external or internal speaker –
whichever is currently set by the Ring (Bell) button.
Brightness Mode:
Increase/decrease the LED intensity
All Button LEDs will be increased/decreased with each
press.
+
Brightness - dual
button simultaneous
press (2 seconds)
Out of Call:
Enter LED brightness change mode. Then Press UP and/
or DOWN arrows to vary intensity.
Mode will automatically exit after 5 seconds after the
last button press.
Status LED ashes YELLOW 3 times and all Button LED’s
will change WHITE. A single beep will sound when
entering brightness change mode.
A short double beep will sound when exiting change
mode.
Ringer
Single Press
Not in Call:
Cycle through the ring tones and the output device
(internal buzzer and external speaker). The last Ringer
type sounded is then saved.
Ring tone playback and the output device changes.
LED FLASHING (Fast) BLUE when Ring Tone is sounded.
Single Press
(no beep sound)
When Bluetooth is OFF:
Turns ON Bluetooth function
LED changes from OFF to FAST FLASHING in BLUE
when searching Bluetooth device(s). LED turns solid
BLUE when connected
If Bluetooth connected but NOT used in Call:
Transfer the audio to the Bluetooth device
LED changes from Solid BLUE to SLOW FLASHING in
BLUE
Bluetooth Device being Used in Call:
Transfer the audio to HF mode, or Privacy/Intelligent
handset if activated
LED changes from Slow Flashing to solid BLUE
Single Press 1.5 sec
(until 1 beep sounds)
Bluetooth function is ON:
Turns OFF Bluetooth function LED turns OFF
Single Press 5 sec
(until 2 beep sounds)
Bluetooth function is ON:
Bluetooth is set to discovery mode for pairing to
Bluetooth devices
LED is FAST FLASHING ORANGE and BLUE, and then
turns solid BLUE when paired and connected.
Single Press 10sec
(until 3 beep sound)
Bluetooth is ON or OFF: Clear all paired Bluetooth
devices and turn o Bluetooth function LED turns OFF
Single Press
(until 1 beep sounds)
In Tracking Mode*:
Send a Quick GPS message to the pre-congured
destination in the Extreme Handset
LED ashes GREEN for 5 seconds.
A beep will sound to indicate that a tracking message
is to be sent#
Single Press 5sec
(until 2 beeps
sound)
Enables / Disables Track button LED Solid GREEN is enabled, LED OFF is disabled
* This action is optional, and only when tracking for your Extreme Handset is congured and activated. Using the Track button only initiates the
command to send a Quick GPS message - check that the Extreme Handset is congured correctly.
# A beep will only sound if audible alerts are enabled in Eagle