Belair W-04R User manual

W-04R
1
DISCLAIMER
• Two people are recommended for the assembly of this product.
• Use hardware provided and tools recommended to avoid any product faults.
• Always assemble product on a clean soft surface to avoid scratching.
PARTS INCLUDED
HARDWARE INCLUDED
TOOLS REQUIRED
46X 46X 41X 4X 12X 2X2X
#2 Phillips screwdriver #2 Robertson screwdriver
ASSEMBLY INSTRUCTIONS
A B
C
E F
D
G
I
JK
L
H

W-04R
2
STEP 1
Start with desk assembly. Ensure that
all pins and cams are inserted into parts
before assembling. Connect desk top A
and large left gable C as shown. Fasten
pins and cams.
STEP 2
Lay desk back B flat and lower top and
gable onto back. Fasten pins and cams.
Flip unit right side up.
STEP 3
Connect return top E to small support
gable H as shown. Fasten pins and
cams.
A
C
B
E
H

W-04R
3
STEP 4
Lay return back F flat and lower top
and small gable onto back. Do not
fasten hardware until next step.
STEP 5
Attach right gable G as shown. Fasten
all pins and cams. Return unit right side
up.
STEP 6
Lay waterfall back J flat and attach
large waterfall end K as shown. Fasten
pins and cams.
F
G
J
K

W-04R
4
STEP 7
Attach small waterfall supports L as
shown. Ensure the cams are facing the
correct direction. Fasten pins and cams.
STEP 8
Attach waterfall top I . Fasten pins and
cams.
STEP 9
To connect the desk and return ensure
that the green lockdowels are inserted
into the desk top. Line the lockdowels
with the slots in the return back. Slide
the return into the desk back. Fasten
pins and cams.
L
L
L
I

W-04R
5
STEP 10
Attach transaction top D . Fasten pins
and cams.
STEP 11
Position waterfall on corner of desk as
shown. Secure with screws provided
through large desk back.
STEP 12
Secure return top to desk top with
connecting flat brackets as shown. Use
cover caps to cover any visible cams
and screws.
D

W-04L
1
DISCLAIMER
• Two people are recommended for the assembly of this product.
• Use hardware provided and tools recommended to avoid any product faults.
• Always assemble product on a clean soft surface to avoid scratching.
PARTS INCLUDED
HARDWARE INCLUDED
TOOLS REQUIRED
46X 46X 41X 4X 12X 2X2X
#2 Phillips screwdriver #2 Robertson screwdriver
ASSEMBLY INSTRUCTIONS
A B C
E
F
D
GIJ
K
L
H

W-04L
2
STEP 1
Start with the desk assembly. Ensure
that all pins and cams are inserted
into parts before assembling. Attach
desk top A and large right gable C as
shown. Fasten pins and cams.
STEP 2
Lay desk back B flat and lower top and
gable onto back. Fasten pins and cams.
Flip unit right side up.
STEP 3
Connect return top E to small support
gable H as shown. Fasten pins and
cams.
A
C
B
E
H

W-04L
3
STEP 4
Lay return back F flat and lower top
and small gable onto back. Do not
fasten hardware until next step.
STEP 5
Attach left gable G as shown. Fasten
all pins and cams. Return unit right side
up.
STEP 6
Lay waterfall back J flat and attach
large waterfall end K as shown. Fasten
pins and cams.
F
G
J
K

W-04L
4
STEP 7
Attach small waterfall supports L as
shown. Ensure the cams are facing the
correct direction. Fasten pins and cams.
STEP 8
Attach waterfall top I . Fasten pins and
cams.
STEP 9
To connect the desk and return ensure
that the green lockdowels are inserted
into the desk top. Line the lockdowels
with the slots in the return back. Slide
the return into the desk back. Fasten
pins and cams.
L
L
L
I

W-04L
5
STEP 10
Attach transaction top D . Fasten pins
and cams.
STEP 11
Position waterfall on corner of desk as
shown. Secure with screws provided
through large desk back.
STEP 12
Secure return top to desk top with
connecting flat brackets as shown. Use
cover caps to cover any visible cams
and screws.
D