Belair Captains Bed with Desk User manual

Captain's Bed with Desk
BOP 4
SHEETS:
1 - Cover Sheet
2 - Captain's Bed Assembly
3 - Large Frame Assembly
4 - Desk Frame Assembly
5 - Desk Assembly
6 - Stair Assembly
7 - Unit Assembly
TWO PEOPLE ARE RECOMMENDED
FOR THE ASSEMBLY OF THIS UNIT.
Always lay components on a
clean soft-cushioned surface
during assembly.
Ensure all hardware are
accounted for before starting
assembly.

3
3
2
1
3
3
Left Hand Configuration
Right Hand Configuration
B
A
A
B
B
A
B A
Captain's Bed Assembly
BOP 4
16+1
Chicago Bolt
4 Rail
16+1
Metal Dowel
For a left hand configuration assemble unit as shown below. For a Right Hand configuration switch the •
Head End (1) and the Foot End (2) .
Large L brackets and 5/8" screws are for securing the captain's bed to the top of the units. (see SHEET 7) •
Use cover caps to cover metal cross dowels on top rails only. •
F
8
Cover Cap
STEP 2
STEP 3
1 2 3
1 Head End 1 Foot End
STEP 1
40
5/8" Screws
H M S
1
Allen Key
10
Large L Bracket
Tools Required:
Allen Key •
Flat Head Screwdriver •

3
1RH
2LH
E
D
4
2RH
4
D EE
D
1LH
E
Large Frame Assembly
BOP 4
4321 E D
Insert KDs and pins into all appropriate hole. Ensure the arrow on the KDs points towards the edge. •
Lay the top upside down as shown below to start assembly. •
Tighten connections as each piece is being attached. •
2 Stringer 24+1 Pin 24+1 KD
1LH & 1RH
Center Support 1 Top 1LH &1RH End
Tools Required:
#3 Phillips Screwdriver •
STEP 3
STEP 1 STEP 2

123
D
E
E
D
BOP 4
Desk Frame Assembly
D E
8+1 KD
8+1 Pin
1LH & 1RH End 1 Top
1 Stringer
Insert KDs and pins into all appropriate holes. Ensure the arrow on the KD points •
towards the outside edge.
Assemble unit as shown below. •
Tool Required:
#3 Phillips Screwdriver •
STEP 1 STEP 2

6+1
KD
D
E
6+1
Pin1
H
2
Large
L Bracket
F
4
5/8" Screws
E
D
P
3
Bookcase
P
2
1.25" Screw
T
8+2
Shelf Support
Insert shelf support into ends first
then attach shelves to supports.
2
2 Shelves
1
1 Desk Top
STEP 1 STEP 2
BOP 4
Captain's Desk Assembly
Lay top upside down to start assembly. Insert KDs and pins into appropriate holes. Ensure the arrow on •
the kd points toward the outside edge.
Assemble unit as shown below. •
L Brackets are attached after all the units have been put together (see SHEET 7). •
Tools Required:
Electric Drill •
#3 Phillips Driver Bit •
#2 Robertson Driver Bit •
STEP 3
T

A
2
Chicago Bolt
B
2
Metal Dowel
M
4
Cover Cap
1 Staircase Gable
1
Stair
Left Hand Configuration
Right Hand Configuration
1
A
B
M
N
N
12
Washer Head
Screw
Stair Assembly
BOP 4
Tools Required:
Allen Key (provided) •
Flat Head Screwdriver •
Electric Drill •
#2 Robertson Driver Bit •
Remove all drawer boxes and secure staircase gable (1) as shown below. •
For a LEFT hand configuration attach gable to the LEFT side of the stairs. For a RIGHT hand configuration attach staircase gable to the RIGHT side of the stairs. •
Extra 6 screws (N) are for securing the staircase to the loft bed. •
STEP 1 STEP 2

Staircase
Large Frame
Bookcase
Desk Frame
Dresser
Captain's Desk
F
H
N
H
F
Front strip
Back edge
of desk
Captain's Bed
BOP 4
Assembly Instructions
Tools Required:
Electric Drill •
#2 Robertson Drill Bit •
STEP 1
* Assemble the large frame, dresser, bookcase
and desk frame as shown below for a Left Hand
configuration. For a Right Hand configuration
switch the dresser and desk frame.
* Lower the captain's bed on to the bottom units
and with the L brackets and 5/8" screws provided
secure the captains bed directly to the tops of the
units
STEP 2
* Line staircase up to bed, ensure the back of
the staircase does not sit on the Chicago bolts.
Attach staircase to dresser and large frame as
shown below.
STEP 3
* Push edge of desk top past front strip and secure
L brackets to desk top from underneath.