Belair Captain's Bed with Extra Single BOP 11 User manual

Captain's Bed with Extra Single
BOP 11
SHEETS:
1 - Cover Sheet
2 - Captain's Bed Assembly
3 - Large Frame Assembly
4 - Bed Frame Assembly
5 - Single Bed Assembly
6 - Stair Assembly
7 - Unit Assembly
TWO PEOPLE ARE RECOMMENDED
FOR THE ASSEMBLY OF THIS UNIT.
Always lay components on a
clean soft-cushioned surface
during assembly.
Ensure all hardware are
accounted for before starting
assembly.

3
3
2
13
3
Left Hand Configuration
Right Hand Configuration
B
A
A
B
B
A
B A
Captain's Bed Assembly
BOP 11
16+1
Chicago Bolt
4 Rail
16+1
Metal Dowel
For a left hand configuration assemble unit as shown below. For a Right Hand configuration switch the •
Head End (1) and the Foot End (2) .
Large L brackets and 5/8" screws are for securing the captain's bed to the top of the units. (see SHEET 7) •
Use cover caps to cover metal cross dowels on top rails only. •
F
8
Cover Cap
STEP 2
STEP 3
1 2 3
1 Head End 1 Foot End
STEP 1
40
5/8" Screws
H M S
1
Allen Key
10
Large L Bracket
Tools Required:
Allen Key •
Flat Head Screwdriver •

3
1RH
E
D
4
2RH 2LH
D
EE
D
4
1LH
E
Large Frame Assembly
BOP 11
4321 E D
Insert KDs and pins into all appropriate hole. Ensure the arrow on the KDs points towards the edge. •
Lay the top upside down as shown below to start assembly. •
Tighten connections as each piece is being attached. •
2 Stringer 24+1 Pin 24+1 KD
1LH & 1RH
Center Support 1 Top 1LH &1RH End
Tools Required:
#3 Phillips Screwdriver •
STEP 3
STEP 1 STEP 2

3
2LH
2RH
1
E
D
D
E
M
BOP 11
Bed Frame Assembly
Insert KDs and pins into appropriate holes to •
start. Ensure the arrow on the kd points
towards the edge.
Use cover caps to cover KDs on the inside of •
the frame.
Tools Required:
#3 Phillips Screwdriver •
D E 1 2 3
10+1
KD
10+1
Pin 1 Top 1 LH & 1RH End 1 Back
STEP 1 STEP 2
4
Cover Cap
M

8
Chicago Bolt
A
8
Metal Dowel
B
8
1.5" Screw
C
3
2 Side Panel
1
1 Head End
2
1 Foot End
3 Glide Support
5
1 Middle Support
4
6
Small L Bracket
I
10 Bed Slat
6
10
Wood Dowel
L
60
5/8" Screw
F
H
12
Large L Bracket
3
3
5
5
5
1
L
F
H
A
B
4
2
6
L
A
B
F
I
C
Single Bed Assembly
STEP 1 STEP 3
BOP 11
STEP 2
STEP 4 STEP 5
Tools Required:
Allen Key (provided) •
Flat Head Screwdriver •
Electric Drill •
#1 Robertson Drill Bit •
#2 Robertson Drill Bit •

1 Staircase Gable
Left Hand Configuration
Right Hand Configuration
1
A
B
M
N
Stair Assembly
2
Chicago Bolt
2
Metal Dowel
12
Washer Head
Screw
4
Cover Cap
BOP 11
1
Tools Required:
Allen Key (provided) •
Flat Head Screwdriver •
Electric Drill •
#2 Robertson Driver Bit •
N
A
M B
Remove all drawer boxes and secure staircase gable (1) as shown below. •
For a LEFT hand configuration attach gable to the LEFT side of the stairs. For a RIGHT hand configuration attach staircase gable to the RIGHT side of the stairs. •
Extra 6 screws (N) are for securing the staircase to the loft bed. •
STEP 1 STEP 2
Stair

Dresser
Large Frame
Left Hand Configuration
Right Hand Configuration
F
H
N
BOP 11
Assembly Instructions
Staircase Captain's Bed Bed Frame
Single Bed
STEP 1
* Assemble the large frame, bed frame and dresser
as shown below for a Left Hand configuration. For a
Right Hand configuration switch the dresser and bed
frame.
* Lower the captain's bed onto the bottom units and
with the L brackets and 5/8" screws provided secure
the captain's bed directly to the tops of the units.
STEP 2
* Line staircase up to bed, ensure the back of the
staircase does not sit on the Chicago bolts.
Attach staircase to the side of the dresser and
large frame as shown below.
Tools Required:
Electric Drill •
#2 Robertson Drill Bit •