Belair W-02AR User manual

W-02AR
1
DISCLAIMER
• Two people are recommended for the assembly of this product.
• Use hardware provided and tools recommended to avoid any product faults.
• Always assemble product on a clean soft surface to avoid scratching.
PARTS INCLUDED
HARDWARE INCLUDED
TOOLS REQUIRED
40X 40X 43X 6X 24X 4X 1X
#2 Phillips screwdriver #2 Robertson screwdriver
ASSEMBLY INSTRUCTIONS
A B C D E F G
H I J K L M N O

W-02AR
2
STEP 1
Start with desk assembly. Insert pins
and cams into all parts. Lay desk back B
flat and attach left gable C . Fasten pins
and cams.
STEP 2
Attach large right gable E . Fasten pins
and cams. Lift base right side up.
STEP 3
Attach desk top A as shown. Fasten
pins and cams.
B
A
C
E

W-02AR
3
STEP 4
Lay large return gable F flat and attach
back O as shown. Fasten pins and
cams.
STEP 5
Flip back and gable upside down. Lay
top D flat and lower gable and back
onto top. Do not fasten pins and cams
until next step.
STEP 6
Attach small gable G as shown. Fasten
all pins and cams. Return unit right side
up.
O
D
G
F

W-02AR
4
STEP 7
Lay large waterfall back H flat. Attach
small waterfall back I as shown. Fasten
pins and cams.
STEP 8
Attach small waterfall supports J K .
Fasten pins and cams.
STEP 9
Attach small waterfall top M . Fasten
pins and cams.
I
H
K
M
J

W-02AR
5
STEP 10
Attach large waterfall top L . Fasten
pins and cams.
STEP 11
Flip unit upside down as shown and
attach corner support N piece with
screws.
STEP 12
Use connecting flat bracket to connect
tops as shown. Secure with small
screws.
L
N

W-02AR
6
STEP 13
To connect desk to return attach small
return gable to large desk gable as
shown. Fasten pins and cams.
STEP 14
Position waterfall topper onto corner
of unit and secure with screws through
desk back and return back.
STEP 15
Use flat connecting bracket to connect
return top to desk top. Use cover caps
to cover any visible cams or screws.

W-02AL
1
DISCLAIMER
• Two people are recommended for the assembly of this product.
• Use hardware provided and tools recommended to avoid any product faults.
• Always assemble product on a clean soft surface to avoid scratching.
PARTS INCLUDED
HARDWARE INCLUDED
TOOLS REQUIRED
40X 40X 43X 6X 24X 4X 1X
#2 Phillips screwdriver #2 Robertson screwdriver
ASSEMBLY INSTRUCTIONS
A B C D E F G
H I J K L M N O

W-02AL
2
STEP 1
Start with desk assembly. Insert pins
and cams into all parts. Lay desk back
B flat and attach right gable C . Fasten
pins and cams.
STEP 2
Attach large left gable E . Fasten pins
and cams. Lift base right side up.
STEP 3
Attach desk top A as shown. Fasten
pins and cams.
B
A
C
E

W-02AL
3
STEP 4
Lay large return gable F flat and attach
back O as shown. Fasten pins and
cams.
STEP 5
Flip back and gable upside down. Lay
top D flat and lower gable and back
onto top. Do not fasten pins and cams
until next step.
STEP 6
Attach small gable G as shown. Fasten
all pins and cams. Return unit right side
up.
O
D
G
F

W-02AL
4
STEP 7
Lay large waterfall back H flat. Attach
small waterfall back I as shown. Fasten
pins and cams.
STEP 8
Attach small waterfall supports J K .
Fasten pins and cams.
STEP 9
Attach small waterfall top M . Fasten
pins and cams.
I
H
K
M
J

W-02AL
5
STEP 10
Attach large waterfall top L . Fasten
pins and cams.
STEP 11
Flip unit upside down as shown and
attach corner support N piece with
screws.
STEP 12
Use connecting flat bracket to connect
tops as shown. Secure with small
screws.
L
N

W-02AL
6
STEP 13
To connect desk to return attach small
return gable to large desk gable as
shown. Fasten pins and cams.
STEP 14
Position waterfall topper onto corner
of unit and secure with screws through
desk back and return back.
STEP 15
Use flat connecting bracket to connect
return top to desk top. Use cover caps
to cover any visible cams or screws.