Belimo GVA-CPL User manual

INSTRUCTION MANUAL
G
VA-
C
PL
C
oupler Replacement
for LV
,
LVK
,
S
V
,
S
VK
G
lobe Valve Actuator
s
7
1
56
7-
0000
1
0
2/14 - Sub
j
ect to chan
g
e. © Belimo Aircontrols
(
USA
)
, Inc
.
1Remove all existin
g
coupler parts. These parts could be
d
ama
g
ed. When replacin
g
the coupler, use only new parts.
Position the actuator to the
f
ully end position (stem up).
Cable should be
p
ointed awa
y
from
y
ou. Manual override ma
y
nee
d
to
b
e turne
d
.
2
Position the cou
p
ler su
pp
ort on the actuator s
p
indle, with the
indicators facing you.
3
P
os
i
t
i
on t
h
e c
l
amps on t
h
e sp
i
n
dl
e
h
ea
d
.
P
os
i
t
i
on t
h
e c
l
amp
parts to the groove o
f
the spindle and in the small slot o
f
the
cou
p
ler su
pp
ort. The
y
should not sli
p
around
.
4
Position the black lock over the clamps to the coupler support
with arrows
f
ace up.
T
he lock can be positioned in only one direction. There are
n
otches on the clamp support prohibiting a position the wrong
d
irection.
Push the black lock full
y
down
.
5
P
os
i
t
i
on t
h
e c
l
amp
h
o
ld
er over t
h
e c
l
amps
.
D
o not pus
h
d
own at t
hi
s po
i
nt
.
6
C
atch the clam
p
s with the small ears of the clam
p
holder
.
Pinch the clamp holder together as shown. Catch the corners
of
the metal clamps by pushin
g
down a bit on the clamp
h
older, so the ears are over the metal clamps. Do not
f
orce it
o
r the plastic could break. I
f
it does not
g
rab all 4 corners take
a
part an
d
d
o a
g
a
i
n
.
7

0
2/14 - Subject to change. © Belimo Aircontrols (USA), Inc
.
INSTRUCTION MANUAL
G
VA-
C
PL
C
ou
p
ler Re
p
lacement
for LV
,
LVK
,
S
V
,
S
VK
G
lobe Valve Actuator
s
Check if the clamps are attached correctly.
The clamp holder should open with the clamps. When the
clamps are not correct, it is possible to damage the ears in the
next step
.
8
Sna
p
the clam
p
holder down to the cou
p
ler su
pp
ort
.
Push down with one
fi
nger on each side as shown. Push until
the snap
f
eature o
f
the clamp holder snaps to the coupler
support. Do not push the snap point with too much
f
orce.
I
f
pushed too
f
ar, clamp holder will look like the “A” image.
P
u
ll
c
l
amp
h
o
ld
er up s
li
g
h
t
l
y to
h
ear a c
li
c
k
.
I
t s
h
ou
ld
l
oo
k
lik
e
i
mage
"B".
9
Final function check
.
Be sure there are no damages or breaks to the parts. Move
the black lock mechanism up and down. If it functions
symmetrically, the function is ok. The black lock should slide
u
p and down tightly. Make sure the snap circled below is in all
the way.
10
C
orrec
t
I
ncorrect