Belkin F1dn102kvm-unn4 User manual

8820-02951 Rev.A00

F1DN102KVM-UNN4: Belkin 2-Port Single Head DP/HDMI to DP/HDMI Video Secure Desktop KVM Switch, No CAC PP4.0

F1DN202KVM-UNN4: Belkin 2-Port Dual Head DP/HDMI to DP/HDMI Video Secure Desktop KVM Switch, No CAC PP4.0

F1DN104KVM-UNN4: Belkin 4-Port Single Head DP/HDMI to DP/HDMI Video Secure Desktop KVM Switch, No CAC PP4.0

F1DN204KVM-UNN4: Belkin 4-Port Dual Head DP/HDMI to DP/HDMI Video Secure Desktop KVM Switch, No CAC PP4.0

F1DN102KVM-UN-4: Belkin 2-Port Single Head DP/HDMI to DP/HDMI Video Secure Desktop KVM Switch PP4.0

F1DN202KVM-UN-4: Belkin 2-Port Dual Head DP/HDMI to DP/HDMI Video Secure Desktop KVM Switch PP4.0

F1DN104KVM-UN-4: Belkin 4-Port Single Head DP/HDMI to DP/HDMI Video Secure Desktop KVM Switch PP4.0

F1DN204KVM-UN-4: Belkin 4-Port Dual Head DP/HDMI to DP/HDMI Video Secure Desktop KVM Switch PP4.0

Objectives

• This guide includes instructions for installing Belkin F1DN102KVM-UNN4 and F1DN102KVM-UN-4, F1DN202KVM-UNN4 and F1DN202KVM-UN-4,

F1DN104KVM-UNN4 and F1DN104KVM-UN-4, F1DN204KVM-UNN4 and F1DN204KVM-UN-4 KVM Switches.

• A KVM allows sharing keyboard, video, mouse, audio and USB peripherals between multiple computers.

• This Manual and additional product documentation is available for online download on Belkin website. For further assistance please refer to: http://www.belkin.com/

us/Resource-Center/Cybersecurity/Secure-KVM-Switching/.

Quick Installation Guide

2/4 Port Secure Single/Dual-Head DP/HDMI-DP/HDMI KVM Switches

Connect peripherals to the KVM

Console Ports:

• Keyboard & Mouse: Keyboard & Mouse:

Connect a USB keyboard and mouse to

the corresponding KVM console port. The

Keyboard and mouse connected lights (rear

panel) will illuminate green. If the keyboard or

mouse are not authorized, the lights will flicker

or not lilluminate..

• Video: Connect the monitor cable to the KVM

console video port. The EDID LEDs (rear

panel) will operate as follows:

–Off: no EDID

–Flicker: EDID read in progress

–On: EDID received

Note: EDID is only read in the first few

seconds of device boot. The secure switch

does not support hot plug or swap of displays.

In any swap of display(s) it is required to

restart the KVM.

• Audio peripherals: Connect headphones /

speakers to the KVM console audio-out port.

• Common Access Card (CAC) Configuration

and Operation: Please refer to the relevant

section

Connect peripherals to the KVM

Computer (Host) Ports:

• Computer keyboard & mouse connection:

Connect each computer to the KVM keyboard

& mouse computer port using a USB A to

USB B cable. Connect the USB A end to the

computer and the USB B end to KVM.

• Computer Video connection: Connect each

computer to the KVM computer video

port using the corresponding video cable

(DisplayPort/HDMI), if two video connections

exist, make sure each PC video 1 is in the

bottom connector.

• Computer audio connection: Connect each

computer to the KVM audio-in port using an

audio cable. Connect one end of the cable

to the computer’s audio-out port using the

1/8" (3.5mm) stereo plug. Connect the other

end of the audio cable to the KVM audio-in

computer port.

–Audio can be frozen on a channel (if

equipped) and allow for the operator

to hear the frozen channel audio when

switched to another channel. An audio

channel can be frozen by pressing and

holding the channel button to be frozen

for 3 seconds. The audio active light will

illuminate. To disable the freeze, press and

hold any channel button for 3 seconds.

The audio active light will move to the

active channel.

Common Access Card (CAC/DPP)

Configuration and Operation:

CAC/DPP connection to the computer requires

a separate USB cable connection and allows

the user to specify whether there is a

connected device required for that computer

or not. This allows the CAC/DPP port to be

connected and controlled separately to the

keyboard, mouse, video, and audio.

• Step 1 – Installation:

1.1 Using the appropriate USB cable, connect

one end of the cable to the computer that

requires CAC, and the other end to the CAC

port on the KVM Switch that corresponds

to the computer. Important Note: Do not

connect the USB cable if CAC functionality

is not needed for that computer.

F1DN204KVM-UN-4 Model is shown

• Verify that all peripherals and computers are turned OFF prior to

connecting them to the product.

• The KVM’s back panel is divided into sections of Console Ports and

Computer Ports.

–Connect the peripherals to be shared by the KVM to the Console

Ports.

–Connect each computer that needs access to shared peripherals to a

specific Computer Ports section.

–Make sure that every computer is connected to a separate Computer

Ports section.

–The push buttons on the product’s front panel indicate which

computer has current access to shared peripherals.

–To switch peripherals between computers, press the appropriate push

button on the product’s front panel.

–Before installing an administrator may have a need to configure the

KVM for CAC or DPP, and channel Illumination colorization. Consult

your administrator for details.

General