Cult 5059413395888 Installation guide

ASSEMBLY & PRODUCT CARE
1 Drawer Desk 1300x500x775mm
5059413395888
Thank you for purchasing this PRODUCT. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary Tools (included)
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the retailer
from whom you bought this product.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE
CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 25 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Read this leaflet in full before commencing assembly.

Fittings and parts checklist
Part Description Qty
1 Carcase 1
2 Legs 4
Fixing
Description
Qty
A M8 Screw nut
4
B M8 Flat washer
4
C
Wrench
1

Step by step assembly instructions
IMPORTANT: To avoid damage to the parts, tighten fixings by hand only
Step One
Place the top (part 1) top side down on a clean carpet or blanket to avoid damage
Step Two
Position leg (part 2) into holes as below then tighten with washer (B) and nut (A) using wrench
(C) provided in clockwise
Note: Failure to tighten legs securely, will cause product to be unstable

Step Three
Repeat step two until all legs (part 2) are assembled
Step Four
Carefully stand Office Desk to upright position.
IMPORTANT: WHEN LIFTING OR MOVING THE OFFICE DESK ALWAYS DO SO FROM THE
UNDER FRAME AND NOT THE OFFICE DESK TOP
Step Five
Secure the office desk to the wall using the anti-topple kit provided, following the instructions
detailed below. When fitted properly, the device will not be visible during general product use.
IMPORTANT: Securing your furniture to the wall with this kit will prevent injury/property damage
from unexpected tipping of furniture, particularly to avoid serious injury to children.

IMPORTANT: The device must be fitted to this product in accordance with the following parts: 2
x plastic cable tie, 2 x plastic wall bracket.
IMPORTANT: Fittings into the wall are not included. You will need to choose screws/fittings
which are appropriate for securing the device to the type of walls you have. If you are unsure
what wall fixing you require, please seek professional advice. The anti-topple device must not
be modified or altered in any way.
1. Position your furniture in desired location in your home. Take the plastic cable tie and feed
through loop hole provided on the back view
2. Then feed the wall bracket onto the cable tie and press bracket firmly onto the wall flat.
3. Mark with a pencil through the bracket holes onto the wall where the wall fixings will need to
be inserted. Temporarily move furniture from wall and prepare necessary screw holes into your
wall.
4. Fit the plastic wall bracket firmly to your wall using suitable wall fixings. Replace furniture
back to your desired position, then attach cable tie through wall bracket and frame firmly. It
should look like the below diagram.
Your furniture is now safe to use in your home. Finish.

Safety Instructions
Never drag furniture when moving it, always lift it.
When lifting or moving a table always do so from under frame and not the table top.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause
damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a
competent person. No liability will be accepted for damage or injury caused by incorrectly
insalled or assembled furniture.
It is recommended that before moving heavy objects to a new location they are completely dis-
assembled to avoid personal injury or damage to the furniture. Please be careful to retain all
fittings when doing this.
IMPORTANT: If an Anti-topple device is included with this unit, you must install it in accordance
with the instructions provided using fixings suitable for the wall type. If unsure, please seek
advice of a professional.
Care and Maintenance
WHEN CARED FOR PROPERLY, THIS HAND CRAFTED FURNITURE WILL PROVIDE YOU
WITH YEARS OF ENJOYMENT IN YOUR HOME.
How to care for Wood furniture (unpainted)
Furniture with a hard lacquer, wax polish or painted surface should be dusted with a dry cloth.
Waxed furniture will need to be given a coat of beeswax a couple of times a year to help
maintain its luster.
Spray polishes are best avoided as they contain silicones which may spoil the furniture’s
surface by building up over time.
Make sure all surfaces are protected from heat and liquids by mats and coasters. Wipe up spills
immediately and ensure that a mat or pad is placed under paper if you are writing.
Extendable dining tables should be left extended for the first few months to avoid an uneven
appearance. Likewise, lamps and ornaments should also be moved regularly.

Our furniture will endure most temperatures in the home but it is best to avoid placing furniture
next to heat sources such as radiators or fires. Be particularly careful with solid wood as the lack
of humidity caused by central heating can cause damage such as warping.
How to care for Painted Wood furniture
Hand painted brush stroke finish's will hold up to everyday wear and tear quite nicely. However,
it is important to remember that your piece is still a wood piece of furniture and should be cared
for as such.
Painted furniture still requires regular dusting with a damp cloth. When very soiled wash with a
solution of mild, non-abrasive detergent and warm water. Wring a cloth nearly dry and work on a
small section at a time, then rinse with clear water drying after..
Never leave water to settle on the surface as this will cause damage. Any liquid spilled onto the
item should be cleaned up immediately using an absorbent cloth.
AVOID chemical cleaners or liquid furniture polish including direct contact with greasy
substances
As with all natural wood products, there will be some movement within the parts as the furniture
acclimatises to its surroundings, you may see slight chipping and cracks where panels meet,
this is a completely natural occurrence with ALL painted products using natural solid timbers.
Painted surfaces can be carefully touched up with matching paint.
There will be various brush lines, slubs, and little inconsistencies in the painted finish, this is all
part of the relaxed handfinished look and feel of hand painted collections.
How to care for Glass furniture
If the product component is chipped or broken, please consult the manufacturer, retailer or
agent with regard to obtaining a manufacturing specification and shape for replacement glass
quoting the model number and batch number.
Do not use the glass as a chopping surface. Do not strike the glass with hard or pointed objects.
Do not sit or stand on horizontal glass surfaces.
Do not place very hot or very cold items against or in close proximity to glass surface(s).
The surface should be protected with coasters, trivets or placemats.
All spills should be blotted up immediately. Do not wipe the spill or this may spread it. Clean the
surface with a clean soft cloth (non-abrasive) and mild detergent or stone soap.
How to care for Metal furniture
Metal furniture requires minimal maintenance:

Cleaning your metal furniture is very simple. Use a soft cotton cloth and clean with mild
detergent or water, using a towel immediately dry the furniture afterwards.
Metal furniture is usually damaged due to rust, as a precaution a soft wax after cleaning will help
seal it.
If it has a few spots of rust, you can treat it with rust remover, following the manufacturers
guidelines. (some finishes are made to look like rust)
Smudges and smears can be removed from metal furniture by using a window cleaner and a
paper towel.
Indoor metal furniture is not recommended for outdoor use.
How to care for Marble furniture
The surface should be protected with coasters, trivets or placemats.
All spills should be blotted up immediately, do not wipe the spill as this may make it spread.
Clean the surface with a clean soft cloth (non-abrasive) and mild detergent or stone soap. Do
not use cleaners containing acids.
WHEN CARED FOR PROPERLY, THIS HAND CRAFTED FURNITURE WILL PROVIDE YOU
WITH YEARS OF ENJOYMENT IN YOUR HOME.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE