NRS Healthcare M66832 User manual

M66832 Adjustable Tilting Over Bed
& Over Chair Table
General Safety Warning
Please ensure these instructions are
fully read and implemented. Failure to
do so may result in injury to the user.
Retain in a safe place for future
reference.
Intended Use
This stylish and versatile table can
be used either over chairs or single
beds. It has four lockable castors
which makes manoeuvring and
positioning the table very easy. It is
height adjustable from 700mm
(27½") to 900mm (35½") and is
width adjustable from 900mm
(35½") to 1100mm (43¼"). The
table top can be tilted to any angle
from flat to 55º by means of a hand
operated locking gas strut. The top
surface comprises two side tables
which do not tilt, enabling the user
to rest a drink while raising the
centre surface. The side tables can
be removed if not required. All
surfaces can be easily wiped clean
UI/M66832/02/17/Iss4
User Instructions
Unpacking
This product is supplied flat
packed and requires assembly
before use.
No tools are required.
Remove the product from its
packaging; Check for damage.
If you see any, or suspect a
fault, do not assemble the
product; contact your supplier
immediately.
Check all parts are present -
see contents list overleaf
NRS Healthcare,
Sherwood House,
Cartwright Way,
Forest Business Park,
Bardon Hill,
Coalville,
Leicestershire,
LE67 1UB,
United Kingdom.
Tel. Head Office: 0330 100 0098
Tel. Customer Services: 0345 121 8111
Email: [e-mail]
www.nrshealthcare.co.uk
Other products in the NRS Healthcare range you may find useful when
using this product:
L35324: Dycem Non-Slip Mat
The Adjustable Tilting Over Bed & Chair Table and Dycem Non-Slip Mats
are from a range of over 3000 daily living aids available from NRS
Healthcare.
To view the full range please visit our website:
www.nrshealthcare.co.uk
or request a catalogue from the number below

Safety Precautions
Do not overload the table top -
Max 15kg when table top is flat.
Do not use the table to transport
objects
It is advised to lock the castors
before using the table.
Take care to remove any
unsuitable items before
raising/lowering the table top
Assembly Instructions
1 - Place the table top assembly on
the floor, face down - see diagram 1
2 - Slide the shorter leg of the
adjustment angle into the table top
centre bar, to the required width, align
the holes in the two parts and secure
with hand wheel - see diagram 1
Care & Maintenance
Inspect on a regular basis the stability
and rigidity of the product, check all
screws are tightened and in good
condition
3 - Repeat step two for the other
side
4- Fit the leg assembly onto the
Adjustment Angle, slide to the
correct height. Align the holes and
secure with hand wheel - see
diagram 2
DIAG: 1
Contents
Description
Qty
Table Top Assembly
1
Side Table
2
Adjustment Angle
2
Hand wheel (Locking Screw)
4
Leg Assembly
2
5 - Repeat step four, for the other
leg.
6 - Turn the table over and lock the
castors
7 - Fit the side table by sliding the
rectangular tubes into the
corresponding tubes in the table top
assembly, depress the spring snap
clips, when sliding the tubes, push
until the clips snap into position,
see Diagrams 3 & 4.
User Instructions
To Raise the Table top press the
handle towards the underside of the
table and raise/lower the top.
Release the handle to lock in position
See Diagram 5
DIAG: 2
DIAG: 3
DIAG: 5
Adjustment
Angle
Hand Wheel
Hand
Wheel
Leg
Assembly
Handle
Side Table
DIAG: 4
Snap Clip
Cleaning
Clean regularly, wiping down with
a soft cloth and a mild
detergent/disinfectant solution
Do not use abrasive cleaners