BeLuce BOXLED MINI User manual

INSTALLATION INSTRUCTIONS
BeLuce Canada Inc., 3900 14th Avenue, Unit 1, Markham, ON L3R 4R3 P: [phone] F: [phone]
BOXLED®MINI
BL716LED
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
1. Do not let power cords touch hot surfaces.
2. Do not mount near gas or electric heaters.
3. Equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to tampering.
4. The use of accessory equipment not recommended by BeLuce Canada Inc., may cause an unsafe condition, and will void the warranty.
5. Do not use this equipment for other than its intended purpose.
6. Servicing of this equipment should be performed by qualified service personnel.
SAVE THESE INSTRUCTIONS!
CAUTION ! ALWAYS MAKE SURE THE POWER IS TURNED OFF before starting the installation
Wiring fixture to power supply, shall be performed by a certified electrician, and wired in a manner that complies with all local and national electrical
codes, as well as the manufacturer’s wiring diagram.
926000207
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LUMENS / WATTAGE / DISTRIBUTION /
VOLTAGE / WET LOCATION / WEIGHT / DIMENSION
SERIES: BL716LED
OPERATION: HT (AC ONLY)/0-10V DIMMING
LUMENS: LO (2,170), MO (3,200), HO (4,219)
WATTAGE: 20W/30W/40W
DISTRIBUTION: SYMMETRICAL
ASYMMETRICAL
VOLTAGE: 120-277V
WET LOCATION: IP66 / NEMA 4X
WEIGHT: 2.6LBS.
DIMENSION: LENGTH: 76MM (3.0")
WIDTH: 190MM (7.5")
HEIGHT: 173MM (6.8 ”)
No user serviceable parts. Refer service to a qualified service
technician. Read instructions prior to installing and/or operating
this device. Installation should be performed by a licensed
electrician/installer in accordance with local codes.

TYPICAL INSTALLATION
BeLuce Canada Inc., 3900 14th Avenue, Unit 1, Markham, ON L3R 4R3 P: [phone] F: [phone]
Mounting hardware
(by others)
Ceiling
Yoke Mount (Standard)
0-10V dimming wires must be run from a different conduit out of the J-Box.
926000207
0-10V LEAD/DALI
Violet (DIM +)
Grey (DIM -)
AC LEADS
Black (hot)
White (neutral)
Green (ground)
Note: For non-dimming, 3-conductor cord is available (upon request).
1. Locate, mark, and install anchors for the
mounting bracket. Refer to the dimensions
for the bracket as shown above.
2. Install the fixture as shown above
(hardware by others)
6.8in
173mm
7.5in
190mm
3.0in
76mm
3.9in
100mm
0.4in
9mm
4” Octagonal j-box
(by others)
Canopy kit (sold
separately)

MOUNTING
BeLuce Canada Inc., 3900 14th Avenue, Unit 1, Markham, ON L3R 4R3 P: [phone] F: [phone]
Aviation Cable (AC)
1. Attach the glider on the bracket using the
washer and screw as shown.
2. Feed the cable through the glider by pressing
the sleeve to release the lock
926000207
Press sleeve to
release lock
Hook Mount (HK)
Attach the clip-hook to the
bracket using the washers
and nut as shown. (Chain by
others)
Clip-hook
Washer
Lock-nut
Pendant Kit (PK)
1. Attach the stem adaptor to the bracket using the screws and lock-
nuts as shown.
2. Attach the stem to the assembly as shown.
3. Pass the power cord through the assembly and stem.
Washer
A/C cable
Gripper
Nut
Adjusting the bracket:
1. Loosen the nut to adjust the angle
2. Retighten nut once the desired
angle is set.
Stem (3/8 IP)
Screw
Stem adaptor
Lock-nut
SAVE THESE INSTRUCTIONS!