Bentel Security KYO 320 User manual

®
INSTALLATION MANUAL
EXPANDABLE MULTIFUNCTION CONTROL PANEL
KYO 320
ISO 14001
9191.BNT2 ISO 14001 IT-52588
ISO 9001
9105.BNT1 ISO 9001 IT-52587

This system can be programmed using the respective KYO320 Software Application 2.0 or higher.
Installation of the system must be carried out strictly in accordance with the instructions described in this manual, and in
compliance with the local laws and bylaws in force.
The KYO320 Control panels have been designed and manufactured to the highest standards of quality and performance.
The KYO320 Control panels have no user-friendly components, therefore, should be serviced by authorized personnel only.
BENTEL SECURITY shall not assume the responsibility for damage arising from improper application or use.
The manufacturer recommends that the installed system should be completely tested at least once a month.
Hereby, Bentel Security, declares that KYO320 Control panels comply with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
BENTEL SECURITY srl. reserves the right to change the technical specifications of this product without prior notice.
Recycling information
BENTEL SECURITY recommends that customers dispose of their
used equipments (panels, detectors, sirens, and other devices) in an
environmentally sound manner. Potential methods include reuse of
parts or whole products and recycling of products, components,
and/or materials.
For specific information see:
www.bentelsecurity.com/en/environment.htm
Waste Electrical and Electronic Equipment (WEEE) Di-
rective
In the European Union, this label indicates that this product
should NOT be disposed of with household waste. It should be depos-
ited at an appropriate facility to enable recovery and recycling.
For specific information see:
www.bentelsecurity.com/en/environment.htm
BENTEL SECURITY s.r.l.
Via Gabbiano, 22- Zona Ind. S. Scolastica
64013 Corropoli (TE) - ITALY
Tel.: [phone]
Fax: [phone]
e-mail: [email protected]
http://www.bentelsecurity.com
2
®

TABLE OF CONTENTS
INTRODUCTION 5
About the System 5
General Features 6
The System and Accessories 6
Technical Specifications 7
Accessory Items 8
KYO 320 features Table 8
IDENTIFICATION OF PARTS 9
About the Control panel 9
MIA-D and ALISON-DVP Keypads 11
Note about Switching Power Supply 11
Readers and Digital Keys 13
Input and Output Expanders 14
INSTALLING 15
Mounting the Main Unit 15
Connecting Keypads 15
Connecting Readers 16
Connecting Input and Output Expanders 16
Terminals 17
Main Unit 17
BPI Peripherals 18
Wiring 18
Connecting BPI Bus Devices 19
BPI bus Wiring Limitations 21
Connecting Detectors 22
Connecting Motion Detectors 23
Glass Break Detectors 24
Connecting Roller-Blind and Vibration Detectors 24
Connecting Fire Detectors 25
Connecting Alarm Signalling Devices 25
Supervised Outputs 26
Connecting Tamper Terminals 27
Connecting the Telephone Line 28
Connecting a Power Supply 28
Connecting the Mains 29
Auto-configuration 29
RAM Battery (see page 11) 29
Thermal Probe 29
PROGRAMMING 31
Configuration (Enrolling Devices) 31
Keypads Page 32
LED Keypads 32
Input Expanders 32
Output Expanders 32
Readers 32
Power station 33
Accessories 34
Hardwired Zones 35
Type 36
Command 37
Attributes 37
Balance Type 38
Threshold 39
Inactivity 39
Cycles 40
Partitions 40
Sensitivity 40
Voice Messages 41
AND Mode Zones 41
VectorRX Wireless Receivers 41
Replacing Wireless Devices 43
Enrolling Wireless Devices 43
Unenrolling Wireless Devices 43
Outputs 43
Type 43
Polarity 43
Attributes 44
Associated Timer 44
Times 44
Oscillation 45
Cycles 45
Events 45
Partitions 45
Telephone 47
Answer 47
Dialling 47
Answering Machine 48
Dialler 48
Dialler book 48
Send Message after ... 49
Messages 49
Options 49
Actions 49
Digital Communicator 50
Voice Messages 52
Compound Messages 53
Teleservice 53
Enable Test Event 54
Installer Maintenance 54
Central Station Maintenance 55
Log – Events setup 55
Events-Actions 55
Telephone action priority 56
Colours 56
Events Details 56
Clear 57
Find 57
KYO320 3

Event Description 57
Scheduler - Arming 71
Type Description 71
Models 71
Options 72
Examples 72
Scheduler - Timers 73
Type Description 73
Models 74
Options 74
Keypad Codes - User 76
Enable on Partitions 77
Associated Timer 78
User menu access 78
Father PIN 78
New PIN 78
Code Type 78
Enable on LCD Keypad 78
Enable on LED Keypad 79
Programming 79
Codes - Installers 79
Lost Installer Codes 79
Codes - Code Types 80
User Codes 80
Installer Codes 82
Digital keys 82
Allowed Operations 83
Attributes 83
Enable on Key Reader 83
KeyFobs 83
Clock 84
On-site downloading 84
Firmware Upgrade 85
Remote Downloading 85
Check Panel 87
APPENDIX 89
K3/VOX2 Voice Board 89
Features 89
Identification of Parts 89
Installation 89
Expanding Listen-in coverage 89
Manual selection 90
Auto-select mode 90
Manual and Auto-select mode 91
K3/PRT2 Printer Interface 91
Identification of Parts 91
Connecting the Printer 91
Installation instructions 91
VectorRX, VRX32-433 and VectorRX-8 Receiver 92
Identification of Parts 92
Choosing a Mounting Location 92
Mounting the Receiver 93
Connecting the Receiver 94
Technical Specifications 94
B-NET MODULE 94
Identification of parts 94
Mounting the B-NET Module 95
Technical Specifications 95
Reset default 95
Reporting Formats 95
TELIM 95
Contact ID 95
SIA/SIA over B-NET 96
dbManager 96
Data Transfer 96
Tools 97
Copying Customer accounts 99
Difference between KYO300-100 (rev. 1.30) and
new KYO320 control panel 100
4

INTRODUCTION
About the System
The full-featured KYO320 security systems have been
especially designed to satisfy all security needs, from resi-
dential to advanced industrial applications.
The objective of the KYO320 is to make end-user oper-
ation simple and help the Installer improve efficiency.
This is achieved by reduced complexity software and
firmware, and remote programming and diagnostic fa-
cilities.
This system provides impressive application flexibility
and many interesting features such as monitoring facili-
ties and telephone access (refer to “Telephone func-
tions”).
KYO 320 has 8 Input zones expandable to 344, and 6
Outputs expandable to 118.
Partitions KYO320 manages 32 independent Parti-
tions — all with Stay/Away control. Each Partition
(group of zones) can be programmed with its own En-
try/Exit and Auto-Arm/Disarm Times, etc., and can be
controlled by digital Keys/Cards, Codes and/or Input
zones.
Events and Actions KYO320 manages over 3000
events . The factory default settings have been purpose
programmed to require few or no changes for standard
applications. However, the programming flexibility of
the Events and Actions (Output, Digital communicator
and Voice Dialler Actions) will allow you to fully custom-
ize the system.
Telephone Functions The Telephone Communicator
manages 50 telephone number. Up to 8 telephone
numbers can be assigned to the Digital Communicator.
Each Communicator number can have its own Cus-
tomer Code and Reporting format (usually assigned by
the Central station).
The Bentel Security Suite Software and B-Mod Mo-
dem (accessory items) reduce on-site time to a mini-
mum by allowing you to provide Teleservice (on-line
Customer enquiry and assistance facilities).
The Teleservice function can also be used for up-
loading, downloading and diagnosis. Up to 4 telephone
numbers can be assigned to this function.
Voice Board The K3/VOX2 Voice Board (accessory
item) manages 64 recordable Voice messages and 32
telephone numbers for the Answerphone, Dialler,
Memo and Ambient-sound recording facilities.
The answering device can function even if the K3/VOX2
Voice Board is absent, but in this case there aren't voice
messages.
Voice communications to and from the Control panel al-
low operations such as: Listen-in; Talk/Listen-in (2Way
Audio); Input status enquiry (with Voice answer); Re-
mote control of appliances (Turn ON/OFF); Arm/Disarm
Partitions; Alarm Reset and Inhibit Calls.
Access to all the “over-the-phone” features requires a
Telephone Access Code — which can be disabled im-
mediately after use.
Scheduler The Scheduler can be setup to Arm/Disarm
Partitions automatically (on a daily or weekly basis),
and to control 64 daily timer events for KYO320.
Wireless Devices This system supports the
VectorRX, VRX32-433 and VectorRX-8 Receiver (ac-
cessory item). The VectorRX and VRX32-433 Receiver
accepts up to 32 Wireless devices (64 with 2 VectorRX
or VRX32-433), such as: PIR Motion Detectors
(AMD10); Magnetic Contacts (AMC10); Glass break
Detectors; Smoke Detectors (ASD10), and up to 16
Wireless Keys (32 with 2 VectorRX or VRX32-433)
(KeyFob) (ARC20). VectorRX-8 Receiver accepts up to
8 Wireless devices and up to 8 Wireless Keys (KeyFob)
(ARC20).
Programming This system can be programmed from
the Keypad, or via the KYO320 Software Application
and a computer. The Software Application (runs under
Windows) provides real-time supervisory facilities (via
connection to an RS232 Interface or Teleservice), and
will allow you to make the fullest use of all the system
features.
KYO320 INTRODUCTION 5

General Features
The KYO320 Control panel
rUp to 344 Alarm zones: 8 zones on the Main Board;
192 on 32 Input Expanders (6 zones per expander);
64 on 32 MIA-D Keypads (2 zones per keypad); 16
on 16 ALISON/32LP LED Keypads (1 zone per key-
pad) and 64 Wireless zones
rUp to 118 Outputs: 6 Outputs on the Main Board (3
Relays and 3 Open-Collectors); 96 on 16 Output Ex-
panders (6 outputs per expander) and 16 on
ALISON/32LP LED Keypads
rUp to 32 backlit LCD Keypads for system control
rUp to 32 Digital Key/Card Readers
r195 User Codes with programmable ‘View’ option,
priority and functions
r10000 Event Log with date and time details
rUp to 8 power stations
r4 wire Bus (protected against short-circuit) for pe-
ripherals
rDual branch bus for protection against tamper
rProgrammable Balance, Operating mode and Alarm
type — for all zones
rInput zones can be programmed to send specific
commands to the Control panel
rOutputs can be programmed as bistable or cyclic
with programmable cycle times and standby status
r32 programmable partitions — each with own zones,
keypads, readers, outputs and times
r195 User Codes with programmable priority and
functions
r500 programmable Digital Keys/Cards
r16 character labels (ID) for the partitions, zones,
keypads, readers, codes, keys/cards, etc. — the as-
signed label will be shown on the keypad display dur-
ing the user operations
r10000 Event Log — provides details of the operation
type, time and user
rRS232 Interface for system programming and moni-
toring
rSoftware (runs under Windows) for Control panel
Programming, Teleservice and Monitoring
Telephone Facilities
rPulse and Touch-tone (DTMF) dialling
r50 Telephone numbers for Telemonitoring,
Teleservice and Voice Calls
rIntegrated Digital Communicator: supports Pulse,
DTMF and FSK Reporting formats
r6 Instant Alarm calls from each Keypad
rProgrammable Test call
rDouble Call
rLine sharing with other Telephone devices
r1200 baud FSK integrated Modem for Teleservice
management
Telephone facilities with K3/VOX2 optional Voice Board
rDialler function: sends recordable voice messages to
up to 32 Telephone numbers
rRemote Inquiry with Voice answer (requires Access
Code)
rRemote control of Outputs, Arm/Disarm operations,
Alarm Reset (requires Access Code)
rRemote Listen-in and multipoint Telephone commu-
nication (Talk/Listen-in)
rAnswerphone function
Scheduler function
rDaily, Weekly and Monthly scheduling
rHoliday and Daylight Saving (BST) changeover
management
rOvertime and Arming delay management
r4 Arm and 4 Disarm operations per day per Partition
r64 independent daily Timer events for KYO320.
Event print-out using optional K3/PRT2 Board
rPrints Events on parallel printer
rReal-time and/or Event Log printout from specified
date to last Event
rEvent filter
The System and Accessories
The Control panel The Control panel is the core of the
system. It has 8-zones (KYO320 expands to 344); 6 Out-
puts (KYO320 expands to 118;) and a 3A Switching Power
Supply (5A accessory item).
Expanders The Control panel manages up to 32 six
zone M-IN/6 Input Expanders and up to 16 M-OUT/6
Output Expanders (6 Open-Collector Outputs per Ex-
pander).
Control Devices The KYO320 accepts up to 32
ECLIPSE and/or PROXI Digital Key/Card Readers
and/or 16 ALISON/32LP LED Keypads, and/or up to 32
MIA-D and/or ALISON-DVP LCD Keypads.
The operating principles of the ECLIPSE and PROXI
Readers are the same, except:
ØECLIPSE Readers accept SAT Keys only and are for
indoor use (unless mounted inside weatherproof
boxes);
ØPROXI Readers have weather strips, and can be in-
stalled indoors or outdoors (IP34 Protection Class)
and accept SAT Keys and PROXI-cards.
ØECLIPSE and PROXI Systems operate without con-
tacts, therefore, are highly resistant to oxidization
and wear.
ØAlison/32LP is a 32 LED Keypad with built-in pro-
grammable Proximity Reader function.
The operating principles of the MIA-D and
ALISON-DVP Keypads are the same, except:
ØMIA-D Keypads have larger displays, 2 on-board
zones and 3 sets of function keys for manual activa-
tion of Alarm status;
ØALISON-DVP Keypads have smaller cases, 1
on-board zone, an integrated Loudspeaker and Mi-
crophone for use with the K3/VOX2 and built-in pro-
grammable Proximity Reader function.
ØALISON-S(B029) is identical to ALISON-DVP but
DOES NOT have a microphone, loudspeaker and
built-in programmable Proximity Reader function.
6

+Unlike KYO300, the new KYO320 control panel
supports all Bentel LCD Keypads (Alison-S,
Alison-DVP, Mia-D e Mia-S). The manufacturer
recommends to comply with following rules:
1- the Keypad from 17 to 32 address must be
Mia-D and Alison-DVP type ONLY;
2- if the number of BPI bus devices is greater than
80, must be utilized Mia-D and Alison-DVP key-
pad ONLY, otherwise the bus BPI bit rate goes
down.
K3/VOX2 The K3/VOX2 Voice board (accessory item)
can be used for Voice Messages, and Telephone Access.
K3/PRT2 The K3/PRT2 Printer Interface (accessory
item) can be used for real-time and/or Event Log print-
out.
Power station The Power station has been especially
designed for Security system applications. The tamper
protected box (protected against delinquency and
forced removal) can house a backup battery for power
supply during black-out. This control panel supports up
to eight BXM12-B/30 3A Power Stations and/or
BXM12-B/50 5A Power stations.
Management Software The management software
(runs under Windows) provides full Programming, Cus-
tomer Database and real-time Supervisory functions,
and will allow you to make the fullest use of all the sys-
tem features.
The B-Mod Modem The B-Mod Modem will allow you
to Upload/Download from/to the remote system and
carry out Teleservice operations (remote diagnosis
and maintenance). The B-Mod/RX will allow you to Up-
load/Download from/to the remote system and carry
out Teleservice and Telemonitoring (send/receive
real-time transmissions).
Technical Specifications
The following table contains the technical Specifica-
tions of the KYO320.
Voltage 230 V~±10% 50/60 Hz
Maximum current
draw 0.9 A
Insulation Class Class I
Power
Supply/Battery
Charger
13.8 V_±1% 3 A (5A
accessory item)
Maximum Current
available for
Peripherals
1.8 A (3.8 A accessory item )
Battery
(Brand and Type)
12V-7Ahor12V-17Ah
YUASA
NP 7-12 FR or NP 17-12 FR or
similar
Case Flame Class UL94-V2 or
higher
Random Digital
Key/Card Codes 4.295.000.000
Operating
Temperature 5 - 40 °C
Dimensions
(WxHxD) 339 x 488 x 108 mm
Weight
(without battery) 5.55 Kg
The following chart shows the current draw (I (mA) col-
umn) and size of the accessory components.
Component I
(mA)
Size
(WxHxD mm)
KYO320 Main Board 250 —
MIA-D Keypad 50 164 x 133 x 44
ALISON-DVP and
ALISON-S(B029) Keypad 40 143 x 115 x 38
ECLIPSE Reader 30 —
PROXI Proximity Reader 30 78 x 108 x 22
ALISON/32LP LED Keypad 70 142 x 115 x 35
M-IN/6 Input Expander 20
108x101x34M-OUT/6 Output Expander 20
Omnia4R 4 Relay Module 120
K3/VOX2 + VOX-REM
Voice Board + Microphone
-Loudspeaker Board
20 —
K3/PRT2 Printer Interface 40 —
BXM12-B/30 Power Station 10 —
BXM12-B/50 Power Station 10 —
VectorRX Receiver 50 146 x 290 x 28
KYO320 INTRODUCTION 7

nAccessory Items
The following chart shows the Control panel accessory
items, and certifications.
MIA-D Backlit LCD Keypad (2 Inputs)
ALISON-DVP Backlit LCD Keypad (1 Input) with
Microphone + Loudspeaker+PROXI
ALISON-S(B029) Backlit LCD Keypad (1 Input) with-
out Microphone + Loudspeaker
ALISON/32LP 32 LED Keypad (1 Input and 1 Output)
M-IN/6 6 Input Expander Module
M-OUT/6 6 Output Expander Module
K3/VOX2 Voice Board
K3/PRT2 Printer Interface
VOX-REM Microphone + Loudspeaker for
Listen-in function
MINI-BOX Microphone + Loudspeaker box
PROXI Proximity Reader
PROXI-CARD Proximity Card
ECLIPSE3ABI Flush mounting, Contactless
Reader— AVE
ECLIPSE3AN Flush mounting, Contactless
Reader— AVE noir
ECLIPSE3DEL Flush mounting, Contactless
Reader— DELTA
ECLIPSE3DN Flush mounting, Contactless
Reader— DELTA noir
ECLIPSE3GE Flush mounting, Contactless
Reader— GEWISS
ECLIPSE3GGE Flush mounting, Contactless
Reader— GEWISS noir
ECLIPSE3GP Flush mounting, Contactless
Reader— GEWISS playbus
ECLIPSE3IN Flush mounting, Contactless
Reader— TICINO international
ECLIPSE3LGT Flush mounting, Contactless
Reader— TICINO light
ECLIPSE3MA Flush mounting, Contactless
Reader— TICINO magic
ECLIPSE3VI Flush mounting, Contactless
Reader— VIMAR idea
ECLIPSE3VIB Flush mounting, Contactless
Reader— VIMAR light
SAT Digital Key, Contactless—for
Key and Proximity Readers
OMNIA/4R 4 relay Module for Output Expanders
BXM12-B/30 3 A Power Station
BXM12-B/50 5 A Power Station
B-MOD Teleservice Modem
B-MOD/RX Teleservice and Telemonitoring Modem
CVSER/9F9F Serial cable for computer link
ADSER/9M25F 25 pin adapter for serial ports
SECURITY SUITE Management Software
VECTOR/RX Wireless Receiver
VRX32-433 Wireless Receiver
VECTOR/RX-8 Wireless Receiver
AMD10 Wireless PIR Detector
AMC10 Wireless Magnetic Contact
ARC20 Wireless Digital Key
ASD10 Wireless Smoke Detector
ASNC Seize microswitch for Keypads
ASNC-MINI Seize microswitch for Proximity
Readers
KST — Thermal Probe
nKYO 320 features Table
KYO 320
Readers 32
Expander-In 32
Expander-Out 16
Power Stations 8
LCD Keypads 32
LED Keypads 16
Compatible LCD Keypads
(MIA-D, ALISON-DV,
ALISON-S with firmware 1.30
or higher ONLY) ALISON-DVP
e ALISON-S (B029)
RX Wireless Receiver Yes
Zones on-board 8
Zones on Keypad 64+16
Zones on Exp-In 192
Wireless Zones 32+32
Total Zones 344
Supervised Relay Outputs 3
On-board Relay Outputs 3
Open-drain Outputs on-board 3
Open-drain Outputs on- Exp-out 96
Total Outputs 102+16
Partitions 32
Total User Codes 195
DTMF User Codes 64 (out of 195)
Installer Codes 5
User Code Types 16
Installer Code Types 3
Keys/Cards 500
Keyfobs (Wireless Keys) 16+16
Events in Log 10000
Total Events-Actions 3418
Customizable Events 32
Timers 64
Fuses 10
Voice Messages 64
K3/VOX2 Voice Board Yes
K3/PRT2 Printer Board Yes
Numbers in Phonebook 50
Telephone Dialler Actions 50
Digital Communicator Actions 100
8

IDENTIFICATION OF PARTS
Please read this section carefully to get an overall view
of the main components of the system and LEDs.
The numbers in boldface (used in this text) refer to the
descriptions in the tables and figures in this section.
The components are generally numbered in clockwise
order. The outlined numbers refer to the common hard-
ware components of the BPI devices and are described
once only — when first encountered.
nAbout the Control panel
Figure 1 shows the maximum configuration of the
KYO320, therefore, some of the components may not
be present on this system.
KYO320 IDENTIFICATION OF PARTS 9
No. DESCRIPTION
1Frontplate screws (2)
2Loudspeaker (supplied with K3/VOX2 Voice
Board)
3Tamper microswitch
4Main Board (see fig. 2)
5Backplate anchor screw locations (4xØ5mm)
6K3/VOX2 Voice board (accessory item)
7K3/PRT2 Printer Interface (accessory item)
8Switching Power Supply (see fig. 3)
9Thermal probe (accessory item)
10 Housing for 12V – 17Ah max. Battery (not supplied)
11 Cable entry
12 Seize microswitch
13 Seize microswitch bracket
14 Loudspeaker Connector
15 Future use connector
16 Terminal board for Telephone line connection
17 K3/VOX2 Voice Board connector
19 K3/PRT2 Printer Interface connector
20 Flash Memory chip
21 Memory Jumper (M) — if inserted, it will allow
the system to save the programmed parameters
during black-out:
o// = parameters will be deleted (at default);
//o = parameters will be saved
22 Switching power Supply connector (connected)
23 RAM chip battery holder
24 Serial Port RS232
25 MICRO LED(RUN):
OFF or ON = Microprocessor blocked
Flickering = Microprocessor OK
No. DESCRIPTION
26 BPI LED:
OFF = BPI Bus OK
ON = BPI Bus Trouble
27 MAINS LED (POW):
ON = Control panel powered by Mains (230 V);
OFF = Mains Failure—the Control panel will be
powered by the backup Battery during blackout
28 RESET LED (RES):
OFF = Microprocessor OK
ON = Microprocessor resetting
29 Self-recover termic Fuse
30 Connector for backup Battery (The control panel
shuthdown the backup Battery due to voltage
drop (Safety threshold 9,6V), because this con-
dition can damage the battery)
32 Terminal board (KEY BUS) for VectorRX,
VRX32-433 and VectorRX-8 Receiver connec-
tion
33 Terminal board (BPI bus) for BPI device connec-
tions
34 Self-recover termic Fuse
35 Self-recover termic Fuse
36 Self-recover termic Fuse
37 Self-recover termic Fuse
38 connector for MIA-D, ALISON-DVP or Alison-S(B029)
Keypad
39 Microprocessor
40 Terminal board for Tamper Line and Input de-
vice connections (Detectors, etc.)
41 Seize connector (connected)
42 Self-recover termic Fuse
43 Self-recover termic Fuse
44 Self-recover termic Fuse
45 Self-recover termic Fuse
46 Self-recover termic Fuse
47 RAM chip
49 Terminal board for Output device connections
(Sirens, etc.)
50 STOP ALARM Jumper: can be used to disable
Outputs no. 1, 2 and 3 (terminals +N1, +A1,
C1-NC1-NA1, +N2, +A2, C2-NC2-NA2, +N3,
+A3, C3-NC3-NA3):
//o = Output Enabled (at default)
o// = Output Disabled
51 Tamper microswitch connector (connected)
53 Stranded wires: connect the Switching Power
Supply to the Main board (connected)
54 Fine Adjustment Trimmer
55 Auxiliary power terminals (13.8 V)
56 Mains terminals
(230V / 50 Hz)

10
9101112
131415161718192021222324
33 34 353231302928 36 37 38 39 40 41 42 43 44 45
59 60 61
46 49
62
666768 65 64
C2
+A2+N2
NA3
C3+A3+N3
+B5
OC2OC3
+FL3L2 L4 +F L6 +F L7 L8 AS
L1
LI LE
+
B046
RED YEL GRN
SEIZE
AUX
COM
BLK
+F L5 +F
51 BPI1 54
+CR -
OPEN
272625 55 BPI2 58
+C R
-
47 48 50
YEL2
63
123
NA1NC1C1
456
+A1+N1
78
NA2Nc2
OC1 +B4 NC3
+F +F +F
STOP ALARM
VOX
PRN
MEM
RUN
RES
BPI
POW
AC/NFG+VGND
B+ L B– GND +V
AC/L
F3.15A/25ØV
F6.3A/25ØV
1
55
23
41
6
8
5
14
13
12
11
10
9
5
7
Figure 1 Kyo320 Control panel components (maximum configuration)

ICON DESCRIPTION
IPartitions Armed
aAlarms in Memory
GTrouble and Zone in Test status
MMessage in Memory
SOpen Panel
TTamper Alarm
bBPI Device Tamper
fFalse Key/Card at Reader
sBPI Device Missing
tTeleservice enabled
rAnswering device enabled
iTelephone line engaged
KYO320 APPENDIX 11
9101112
131415161718192021222324
33 34 353231302928 36 37 38 39 40 41 42 43 44 45
59 60 61
46 49
62
666768 65 64
C2+A2+N2
NA3
C3
+A3+N3
+B5
OC2OC3
+F
L3L2 L4 +F L6 +F L7 L8 AS
L1
LI LE
+
B046
RED YEL GRN
SEIZE
AUX
COM
BLK
+F L5 +F
51 BPI1 54
+C R
-
OPEN
272625 55 BPI2 58
+CR
-
47 48 50
YEL2
63
123
NA1NC1C1
456
+A1+N1
78
NA2Nc2
OC1 +B4 NC3
+F +F +F
STOP ALARM
VOX
PRN
MEM
RUN
RES
BPI
POW
YEL
16
21
17
25
26
27
28
39
2
0
4
9
15
5
1
5
0
23
24
22
38
19
4
1
32
30
4
7
33
4
1
4
2
4
6
4
5
4
4
4
3
37 36
34
35
29
Figure 2 Kyo320 Main board components
AC/N
FG
+V
GND
B+
L
B–
GND
+V
AC/L
F3.15A/25ØV
F6.3A/25ØV
62
57
59
53
54
55
56
58
61
60
57a
Figure 3 Switching Power Supply components
No. DESCRIPTION
57 Switching Power Supply screw
58 Fuse — protects against over-
load (F 3.15A 250V)
59 Rivet
60 Fuse — protects against Battery
polarity inversion (F 6,3A 250V)
61 Mains LED
62 Switching Power Supply con-
nector to connect the probe 9
nMIA-D and ALISON-DVP Keypads
Note about Switching Power Supply
KYO320 control panel supports BAQ35T12 (13.8 V_±1% 3A) Switch-
ing Power Supply (factory default).
If it is necessary more Power Supply/Battery charger the BAQ60T12 (13.8
V_±1% 5A) is avaible (accessory item). In this case it is necessary to re-
move the BAQ35T12 from the backplate of control panel and so work care-
fully through the following steps.
1-Disconnect the BAQ35T12 from Main Board;
2-remove the screw (57a) and pull the BAQ35T12 from the hook on the
backplate of control panel;
3-Before installing cut the two BAQ60T12 wires for connecting battery;
4-Insert the BAQ60T12 in the same location of BAQ35T12 (Figure 1): be-
fore in the hook and then secure the screw (57a).
5-Connect the connector (53) on Main Board and if scheduled the termal
probe (KST), connector (62);
Otherwise KYO320 control panel can manage BXM12-B/30 and
BXM12-/50 Power Stations (see page 7).

12
COMNONC
2
abc A B
C
D
ESC
13
def
5jkl 4ghi 6
mno
8tuv 7
pqrs 9 wxyz
0OFF
#
ON
2abc A B
C
D
ESC
13
def
5jkl 4ghi 6
mno
8tuv 7
pqrs 9 wxyz
0OFF
#
ON
OUT
PIN
PIN
PIN
PIN
PIN
PIN
Inserimento Aree
Inserimento A, B, C o D
Disinserimento Aree
Reset Memorie
Blocco AllarmeQ
Cancella Telefonate
Arming Partitions
Arming Type A, B, C or D
Disarming Partitions
Reset Alarms
Stop AlarmsQ
Clear Calls
Aree
Inserite
Sabotaggio
Centrale
Scomparsa
Periferica
Chiave
Falsa
Sabotaggio
Periferica
Sabotaggio
Guasto
Allarme
Messaggio
Teleassist.
Abilitata
Rispondit.
Abilitato
Telefonata
in corso
Armed
Partitions
Alarm
Message
Warning
Panel
Tamper
Tamper
Peripheral
Tamper
False
Ke /Cardy
Missing
Peri heralp
Teleservice
Enabled
Answer
Phone ON
Call in
progress
ETIDFBL1ALS-S 0.0 290903 D10
o
or
1
2
3
4
5
6
7
8
http:\\www.bentelsecurity.com
n.Des.
O
ABC D
o
EE
EDE
ECE
WINTEK WM-C1602N-2GLYc
A
K
PICVUE 160206QGL01
K
A
63
69
76
66 67
64 70
65
71
75
79787775
74a 81 82 77 74
66
64a7372
71 82a 7181
7674
75
89
89c
Figure 4 ALISON-DVP and Alison-S(B029) (Alison-S(B029) DOES NOT manage Voice, Microphone+Loudspeaker
functions and Proximity reader)
2abc 3def 1
5jkl 6
mn
o
4ghi
8tuv 97pq
rs
0
A
#
B
C
D
E
S
C
wx
yz
OFFON
1234
ON
5
+
C
R
–
+F
L1
L2
SNATCH
BPI 5V
5V
12V
BPI
LEV
BL232
COM NO NC
2abc 3def 1
5jkl 6
mn
o
4ghi
8tuv 97pq
rs
0
A
#
B
C
D
E
S
C
wx
yz
OFFON
13572468
63
69
71
66 67 66
65 64 70 71
72 80
71
75
767479787776
7573
7468
81 74 82 77 74 7181
Figure 5 MIA-D keypad
COMNONC
ETIDFBL1ALSL32P 0.0 030304 D10
1 9 17 25
2 101826
3 111927
4 122028
5 132129
6 142230
7 152331
8 162432
34567812
http:\\www.bentelsecurity.com n.Des.
Stop allarmi
Stop alarm Perdita datario Clock Wrong
Aree Inserite
Armed Part. Allarme Alarm Guasto Warning Pronto Ready Sabotaggio Tamper Sabot.Centrale Panel Tamper ZoneEscluse Bypassed Zones Teleassistenza Teleservice
Guasto Fusibile
Fuse Trouble Mancanza Rete Mains Failure Guasto Batteria Battery Trouble ScomparsaDisp. Missing Device Guasto Linea Tel. Line Down Dati di Fabbrica Default Settings
2
abc A B
C
D
ESC
13
def
5jkl 4ghi 6
mno
8tuv 7
pqrs 9 wxyz
0OFF
#
ON
2
abc A B
C
D
ESC
1 3
def
5jkl 4ghi 6
mno
8tuv 7
pqrs 9 wxyz
0OFF
#
ON
OUT
66 67 66
69 64
657575
73
72
76
70 7179787771
81 82 77 7471 7181
7674
89
8
9a
89c
89b
89d
Figure 6 Alison/32LP Keypad - The 32 LEDs on ALISON/32LP Keypads represent Partitions 1 -32 (refer to the
USER MANUAL for details).

No. DESCRIPTION
63 Backlit LCD, 2 rows x 16 columns
64 Buzzer
64a Microphone (on ALISON-DVP only)
65 Seize microswitch connector
66 Frontplate screws (2)
67 Down flip
68 Microprocessor (solder side on ALISON-DVP)
69 BPI Level Jumper:
oo = 12 V (at default); // =5V
70 Cable entry
71 Board Supports (4)
72 Terminal board
73 BPI Level Jumper:
12V //o 5V = 12 V (at default)
12V o// 5V=5V
74 Screw locations (4 on MIA-D;2onALISON
-DVP and Alison/32LP) for mounting to 10x10
outlet boxes or similar
74a Loudspeaker Input
75 Tamper microswitches (2)
76 Screw locations (2) for mounting to mod. 503
outlet boxes or similar
77 Screw locations (2) for mounting on single
gang,2-gang or similar
78 PCB Clip
79 Seize microswitch (order code: ASNC)
80 Address DIP Switches
81 Board Supports (2)
82 Seize microswitch bracket location
82a Loudspeaker (on ALISON-DVP only)
nReaders and Digital Keys
No. DESCRIPTION
83 Backplate anchor screw locations (2)
84 Microprocessor
85 Connection wires:
red = +; white = C;blue=R; black = –
86 Seize microswitch connector
87 Seize microswitch (accessory item)
88 Seize microswitch location
89 Sensitive field
89a Address keypad LEDs
89b Address PROXI LEDs
89c PROXI reader LEDs
89d Address LEDs
90 Cover screw
91 Key slot
92 Command button
93 Snap catch
94 Cable entry
95 Tamper microswitch
KYO320 APPENDIX 13
CNONC
1234
ON
5
–
12V
R
C
5V
+
LB092-P
BPI
5V BPI LEVEL
SNATCH
1234
ON
5
d) e) f)
83
a) b)
c)
73 85 86 87 888480
95
69
94
83
93
80
73
72
89
90
9192
69
Figure 7 Readers and Digital Key: PROXI Proximity Reader — internal view (a) external view (b); PROXI-CARD for
Proximity Reader (c); ECLIPSE Contactless Reader with 5 DIP Switches , Magic Version — side view (d) front view
(e); SAT Key for ECLIPSE and PROXI Readers (f)

LED DESCRIPTION
red
I
Status of Reader Partitions
OFF = ALL the Reader Partitions are
DISARMED;
ON = AT LEAST ONE of the Reader Partitions
is ARMED.
Slow blinking = AT LEAST ONE of the Reader
Partitions has AT LEAST ONE Alarm or Tamper
memory, and all Partitions are DISARMED.
Fast blinking = AT LEAST ONE of the
Reader Partitions has AT LEAST ONE Alarm
or Tamper memory, and AT LEAST ONE Par-
tition is ARMED.
amber
A
A Mode Arming:
OFF = the status of the Keypad Partitions
DOES NOT MATCH the A Mode Arming con-
figuration;
ON = the status of the Keypad Partitions
MATCHES the A Mode Arming configuration.
green
B
B Mode Arming:
OFF = the status of the Keypad Partitions DOES
NOT MATCH the B Mode Arming configuration;
ON = the status of the Keypad Partitions
MATCHES the B Mode Arming configuration.
+These descriptions are valid also for
ALISON-DVP keypad proximity reader LEDs.
+These descriptions are not valid when a
key is present at the Reader.
+If ALL THREE LEDs blink, the system HAS NOT
RECOGNIZED the Key/Card (false Key/Card).
If ONE LED blinks, one or more of the Partition
zones is already in Alarm status.
nInput and Output Expanders
No. DESCRIPTION
96 Seize microswitch (solder side)
97 Microprocessor
98 Buzzer
No. DESCRIPTION
99 Buzzer Mode Jumper:
1ooo 3 = buzzer OFF (at default)
1//o 3 = buzzer will activate when terminal
[OC6] opens
1o// 3 = buzzer will activate when terminal
[OC6] connects to negative
100 Tamper ands Seize mode Jumper:
oo = Microswitches enabled (at default)
// = Microswitches disabled
101 Tamper microswitch
102 Terminal Board
103 Frontplate screw locations (4)
104 Expander (Input, Output, etc.)
105 Expander screws (2)
106 Cable entry
107 Screw locations (2) for mounting to 503 outlet
box or similar
108 Cable duct entry
109 Surface mounting screw locations (2)
110 Seize microswitch bracket
111 Plastic tooth (closes the microswitch)
14
5V 12V
BPI 5V
BL240
TAMP.
DIS.
BPI LEV.
1234
ON
5
R
C
+
L1
L3
L5
+F
+F
+F
L2
L4
L6
1234
ON
+F
+F
+F
+F
R
C
OC3
OC1
+
OC2
OC4
OC5
OC6
BPI 5V
3
1TAM P.
DIS.
BPI LEV.
5V
BL238
12V
72
a
)b)
69 9697 73 72 80 69 73
102 80 101 100 102 96 101
98
99
100
97
Figure 8 M-IN/6 Input Expanders (a) and M-OUT/6
Output Expanders (b)
103
103 103 104 105 96 106 107 108 109 107
111 103 105 101 109 110
Figure 9 Module and Expander box

INSTALLING
Mounting the Main Unit
Please read this section carefully to get an overall view of
the steps involved in installing the KYO320 Main Unit. The
KYO320 Main Unit should be located in a safe, dry place
that is far from sources of interference.
Once you have selected a suitable place, create a lay-
out of all the system peripherals (Keypads, Readers,
Detectors, etc.) and ensure that you will be able to con-
nect the Main power, peripherals, and if necessary, the
telephone line to the KYO320 without difficulty. Allow at
least 5 cm of free space around the Main Unit for air
flow.
!The Main Unit must be at least 2 metres from
GSM and radio relay systems.
Work carefully through the following steps (see Figure
on page 10).
1. Remove the screws 1and frontplate.
2. Install add-on modules and boards (K3/VOX2,
etc.), refer to the respective paragraphs for instruc-
tions.
3. Drill the holes for the cabinet and Seize microswitch
bracket anchor screws (5 and 13 respectively).
4. Pull the connection wires through the wire entry 11
then attach the cabinet and Seize microswitch
bracket to the wall.
+DO NOT over tighten the screws as this may dam-
age the Seize microswitch bracket.
5. Complete the connections — DO NOT connect the
MAINS until all other wiring has been completed.
6. Connect the Mains Power (refer to “Connecting the
Mains Power”).
7. Program the system (refer to the
“PROGRAMMING” section and the
“PROGRAMMING FROM KEYPAD” Guide for in-
structions).
nConnecting Keypads
Keypads should be located in places where full control
of the system is required: MIA-D,ALISON-DVP,
Alison-S(B029) and Alison/32LP Keypads can be sur-
face mounted on Mod. 503, 10x10 single gang and dou-
ble gang outlet boxes or similar.
+Keypads should be mounted at eye level for easy
viewing.
Work carefully through the following steps (see Figures
on page 12) and/or respective manuals.
1. Remove the screws 66 and frontplate.
If you are installing a MIA-D Keypad go to step 3.
If you are installing an ALISON-DVP Keypad go to step 2.
2. Disconnect the Loudspeaker 82a from its Input
74a.
3. Push the PCB clip 78 upwards to release the PCB.
4. If you are surface mounting the Keypad: drill the
holes for the backplate anchor screws 76, and if re-
quired, for the Seize microswitch bracket screw 82.
5. If you are fitting a Seize microswitch (Order Code:
ASNC), push it firmly into its location (79 in Fig. 7)
and ensure that the Seize microswitch lever is held
firmly in position by the bracket tooth.
6. Pull the wires through the wire entry 70.
7. Using the anchor screws, secure the backplate and
Seize microswitch bracket to the wall.
+Seize microswitches cannot be fitted to outlet
mounted Keypads.
8. Replace the PCB, and if required, connect the Seize
microswitch to the connector 65.
If you are installing a MIA-D Keypad go to step 10.
If you are installing an ALISON-DVP Keypad go to step 9.
9. Connect the Loudspeaker 82a to its Input 74a.
10. Assign the Keypad Address, then set the BPI Level
and complete the connections on the terminal
board (refer to “Connecting BPI Peripherals” for in-
structions).
11. Reattach the frontplate.
KYO320 INSTALLING 15

nConnecting Readers
Readers can be located in places where limited control
of the system is required (Arming, A and B Mode
Arming, Disarming and Stop Alarm operations).
This system supports Digital Key and Proximity Card
Readers.
Key Readers Key Readers can be flush mounted to
most standard domestic light-switch/plug-socket outlet
boxes (refer to “Accessory items” in the
“INTRODUCTION” for the available models).
+Digital Key Readers must be at least 10 cm apart.
To install Key Readers, work carefully through the fol-
lowing steps (see Figure on page 13).
1. Assign the Reader Address, then set the BPI Level
and complete the connections on the terminal
board (refer to “Connecting BPI Peripherals” for in-
structions).
2. Fit the Reader in its placement (use the standard
procedure for fitting domestic light-switches and
plug sockets).
Proximity Readers Proximity Readers can be surface
mounted, or mounted to Mod. 503 outlet boxes or simi-
lar. Proximity Readers are fitted with weather strips
(Protection Class IP34), therefore, are suitable for out-
door use.
+Proximity Readers must be at least 50 cm apart.
To install Proximity Readers, work carefully through the
following steps (see Figure on page 13).
3. Remove the screw 90 (if fitted), then using a screw-
driver or similar tool push down on the catch 93 to
release the frontplate.
4. Drill the holes for the backplate and Seize
microswitch bracket anchor screws (83 and 88 re-
spectively).
5. If you are fitting a Seize microswitch (Order Code:
ASNC-MINI), push it firmly into its location (87 in
Fig. 7) then connect it to the connector 86. Ensure
that the Seize microswitch lever is held firmly in po-
sition by the bracket tooth.
6. Secure the Reader and Seize microswitch bracket
to the wall.
7. Assign the Reader Address, set the BPI Level and
complete the connections on the terminal board
(refer to “Connecting BPI Peripherals” for instruc-
tions).
8. Reattach the frontplate.
nConnecting Input and Output Expanders
Locate the Input and Output Expanders as near as pos-
sible to the devices they will be connected to.
The Expander box can be surface or flush mounted
(see Figure on page 14).
1. Remove the knockout (106 or 108 as required).
2. –Surface mounting: drill the holes for the backplate
and Seize microswitch bracket anchor screws (109
and 110 respectively).
–Flush mounting to Mod. 503 outlet box or similar:
drill the hole for the Seize microswitch bracket an-
chor screw 107. No other drilling is required for
Flush mounting.
3. Pull the wires through the wire entry.
4. Secure the back box and Seize microswitch
bracket to the wall.
+The Seize microswitch bracket 110 must be fitted
as shown in the figure on page 14 (with the plastic
tooth to the left of its location).
5. Replace the PCB inside the box.
6. Assign the Address, then set the BPI Level and com-
plete the connections on the terminal board 72 (refer to
“Connecting BPI Peripherals” for instructions).
7. Remove the Jumper 100 — to enable the Tamper
and Seize microswitches.
8. Using the Jumper 99, set the Output Expander
buzzer mode:
1ooo 3 > buzzer disabled (at default);
1//o 3 > buzzer will sound when terminal [OC6]
opens;
1o// 3 > buzzer will sound when terminal [OC6]
closes to negative.
16
COM NO
NC
to the
Tamper line
Figure 10 Mounting Key Readers

9. Replace the frontplate.
+Ensure that the plastic tooth 111 on the frontplate,
closes the Tamper microswitch 101 properly.
Terminals
This section describes the Main Unit and BPI device ter-
minals.
The layout of Terminal Description table is as follows:
Øthe Ter. column shows the terminal identifier;
Øthe DESCRIPTION column provides a brief descrip-
tion of each terminal;
Øthe v(V) column shows the terminal voltage (the hy-
phen “–” indicates that the voltage cannot be speci-
fied for the terminal concerned);
Øthe I(A) column shows the maximum current (in Am-
peres) that can circulate on the terminal (the hyphen
“–” indicates that the current cannot be specified for
the terminal concerned);
Øthe numbers in brackets refer to the following notes.
(1) The total current draw of Main Unit terminals [+A3],
[+N3], [+A2], [+N2], [+A1], [+N1], [+B4], [+B5], [+F],
[+F1], [+] and [RED] must not exceed 3.8A for KYO320.
(2) The current draw of BPI device [+] terminals is:
ØKeypad = 0.05 A for MIA-D, and 0.04 for
ALISON-DVP and Alison-S(B029), 0.07A for
Alison/32LP
ØReader = 0.03 A
ØInput Expander = 0.02 A
ØOutput Expander = 0.02 A
+These values refer to the current draw of the BPI
devices with no loads.
(3) The total current draw of the Input/Output Expander
[+F] terminals should not exceed 0.4 A.
nMain Unit
Ter. DESCRIPTION v(V) I(A)
NA3
NC3
C3
Programmable Output no. 3
(changeover switch contacts)
–3
+A3 Programmable Output no.3 (posi-
tive), protected by fuse
13.8 3(1)
+N3 Programmable Output no. 3 (in-
trinsic security), protected by fuse
13.8 3(1)
NA2
NC2
C2
Programmable Output no. 2
(changeover switch contacts)
–3
+A2 Programmable Output no. 2 (posi-
tive), protected by fuse
13.8 3(1)
+N2 Programmable Output no. 2 (in-
trinsic security), protected by fuse
13.8 3(1)
NA1
NC1
C1
Programmable Output no. 1
(changeover switch contacts)
–3
Ter. DESCRIPTION v(V) I(A)
+A1 Programmable Output no. 1 (posi-
tive), protected by fuse
13.8 3(1)
+N1 Programmable Output no. 1 (intrin-
sic security), protected by fuse 46
13.8 3(1)
+B4 Positive power supply to peripher-
als, protected by fuse (will be
powered by the battery during
Mains failure)
13.8 3(1)
+B5 Positive power supply to peripher-
als, protected by fuse (will be
powered by the battery during
Mains failure)
3(1)
MNegative 0–
OC1 Programmable Output no. 4
(Open-Collector)
01
OC2 Programmable Output no. 5
(Open-Collector)
01
OC3 Programmable Output no. 6
(Open-Collector)
01
AS 10 KWBalance Tamper Line ––
L1
:
L8
Programmable Input Line ––
+F Power supply to detectors (posi-
tive), protected by fuse (will be
powered by the battery during
Mains failure)
13.8 3(1)
+F1 Power supply to detectors (posi-
tive), protected by fuse (will be
powered by the battery during
Mains failure)
13.8 3(1)
BPI1 1° branch of the BPI bus for the
BPI peripherals:
+= positive protected by fuse
C= Command
R= Response
–= Negative
13.8 3(1)
BPI2 2nd branch of the BPI bus for the
BPI peripherals:
+= positive protected by fuse
C= Command
R= Response
–= Negative
13.8 3(1)
RED
BLK
YEL
YEL2
KEY BUS:
positive protected by fuse
negative
Receiver 1
Receiver 2
13.8 0.5
(1)
GRN data
-Earth Terminal 0–
LE External telephone line terminals ––
LI Line-sharing devices terminals (for
Answerphone, telephone, fax, mo-
dem, etc.)
––
KYO320 INSTALLING 17

nBPI Peripherals
The terminals shown in the following table are common
to all BPI peripherals.
Ter. DESCRIPTION v(V) I(A)
+Power supply: positive 13.8 (2)
CCommand ––
RResponse ––
–
M
Power supply: negative
(On ALISON-DVP and
Alison-S(B029) keypad only)
0–
Keypad Keypads have the common BPI bus connec-
tion terminals, and the following terminals.
Ter. DESCRIPTION v(V) I(A)
+F Power supply to Detectors (posi-
tive), protected by resettable fuse
13.8 0.4
L1 Programmable Input Line ––
L2 Programmable Input Line (MIA-D
only)
MIC
SP+
SP–
Terminals for the connection of the
K3/VOX2 Voice Board
(ALISON-DVP only)
MPower supply to Detectors (nega-
tive)
0–
OUT Programmable Open-collector Output
(Alison/32LP and Alison-DVP only)
0 0,15
Input Expanders Input Expanders have the common
BPI bus connection terminals, and the following termi-
nals.
Ter. DESCRIPTION v(V) I(A)
+F Power supply to Detectors (posi-
tive), protected by resettable fuse
13.8 (3)
L1
:
L6
Programmable Input Lines ––
Ter. DESCRIPTION v(V) I(A)
MDetector Power supply (negative)0–
Output Expanders Output Expanders have the com-
mon BPI bus connection terminals, and the following
terminals.
Ter. DESCRIPTION v(V) I(A)
MPower supply (negative) to the pe-
ripherals connected to the
Open-Collector Outputs
0–
+F Power supply (positive) to the pe-
ripherals connected to the
Open-Collector Output, protected
by resettable fuse
13,8 (3)
OC1
:
OC6
Programmable Open-Collector
Output
0 0.15
Wiring
The section describes how to wire the Main Unit, BPI
bus peripherals and various security devices.
Each wiring diagram refers to a specific type of device
(BPI bus devices, Detectors and Signalling devices).
+Use shielded cable for all connections, with one
end connected to negative and the other floating.
!The end of the stranded conductor must not be
soft soldered in places where it is subject to
contact pressure.
!The Mains wiring must comply with the rules
for double or reinforced insulation.
+Use an adhesive cable grip to secure the wires to
the terminal boards.
The wiring diagrams show some of the many tailored
solutions this system provides.
18
+ CR–
BPI device
CR+–
BPI device
RC+–
Panel
Power station
RC
+
RC
+BPI IN BPI OUT
BPI device
RC+–
Figure 11 Connection of 4 BPI Devices

About the Wiring Diagrams The locations of the ter-
minals in the wiring diagrams may be different to those
on the board.
Øthe Zone terminals may belong to the Control panel,
Keypads or Output Expanders;
Øthe Open-Collector Output terminals may belong to
the Control panel or Output Expanders;
Øthe Input zone and the Open-Collector Output termi-
nals (in the wiring diagrams) can be found on the
Main Unit or Expanders;
Øonly the terminals required for the connection are
shown in the wiring diagrams.
Connecting BPI Bus Devices
The BPI bus supports the following devices:
Øup to 32 Keypads
Øup to 32 Readers
Øup to 32 Input Expanders
Øup to 16 Output Expanders
Øup to 8 Power stations
Øup to 16 LED Keypads
Electrical Connections The BPI bus devices must be
connected in parallel to terminals [+], [C], [R], [–] on the
Main Unit, as shown in Fig. 11.
The Power Station has two groups of terminals for the
BPI bus connection: the BPI-IN group — for the Power
Station; and the BPI-OUT group — for the BPI devices
connected downstream of the Power Station.
The two groups of terminals are electrically isolated,
therefore, all the cables and devices connected down-
stream of the Power Station will not load the Control
panel BPI bus.
Refer to the Power Station Instructions leaflet for further
details.
+Only one Power Station can be connected to each
shunt of the Control panel BPI bus (see Fig. 12).
Dual Branch Bus The Control panel BPI bus has two
independent branches:
Branch 1 (BPI1) — terminals no. 51, 52, 53 and 54;
Branch 2 (BPI2) — terminals no. 55, 56, 57 and 58.
Each Branch is protected by its own fuse, therefore,
short-circuit on one branch will not impair the operating
capacity of the other.
+The Outdoor Control panel BPI bus peripherals
should be connected to one Branch of the BPI bus,
and the Indoor peripherals to the other. In this way,
tamper on one branch will not impair the operating
capacity of the other.
Assigning Addresses You must assign an Address
to each of the BPI bus devices. The assigned Address
will allow the Control panel to distinguish one device
from another. The Peripheral devices are divided into
types: Keypads, Readers, Input Expanders, Output Ex-
panders and Power Stations.
Devices of the same type (e.g. two Readers) must
have different Addresses.
Devices of different types (e.g. a Keypad and a
Reader) are intrinsically different, therefore, may have
the same Address. The BPI bus peripheral Addresses
can be assigned in any order, using the DIP switches 80
(refer to Table 1).
+Output Expanders have 4 DIP switches, and can be
assigned to Addresses no. 1 through no. 16 ONLY.
For the Address Combinations refer to the num-
bers in brackets in Table 1.
+Refer to the Power Station Instructions leaflet, and
the keypads Instructions leaflet, for the Address
setup. Power Stations can be assigned to Addresses
no. 1 through no. 8 ONLY. The position of DIP
switch no. 1 in uninfluential.
Setting the BPI Level The BPI Level determines the
maximum voltage the BPI bus can carry. Some BPI de-
vices have 5V and 12V options.
KYO320 INSTALLING 19
Yes
Yes
NO
BPI
device
Panel
Power
station
BPI
device
BPI
device
BPI
device
BPI
device
Power
station
BPI
device
BPI
device
BPI
device
BPI
device
Power
station
BPI
device
Power
station
Figure 12 Connecting a Power Station

+This Control panel operates at 12V, therefore, all
the peripheral devices must be set at 12 V.
Using the Jumpers 69 and 73, set the BPI Level as fol-
lows:
BPI Level Jumper 69 Jumper 73
5V // 5V 12Vo// 5V
12 V oo 5V 12V//o 5V
+Refer to the Power station Instructions leaflet for
the BPI Level setup.
ALISON/32LP ASSIGNING ADDRESSES To assign
the addresses to the ALISON/32LP Keypad and Prox-
imity Reader work carefully through the following step:
1.Remove the frontplate in order to generate a Tamper
status.
2.Connect the Keypad to the Control panel BPI BUS
(terminals +, C, R, -).
3.Remove the jumper 73:
Øafter 5 seconds the keypad will emit an audible signal
and the 4 LEDs on the left (89a in Figure 8) will turn ON;
Øthe four pairs (up/down) of LEDs (89d in Figure 8) will
simulate 4 DIP switches;
Øone of the first pair of LEDs will blink to indicate ac-
cess to the Addressing phase.
4.Assign an Address to the Keypad.
ØUse Aor Bto select the LED/DIP switch.
ØUse Cor Drespectively, to turn the LED ON or
OFF as required, in accordance with the following
logic:
Upper RED LED ON = DIP switch ON
Lower LED ON = DIP switch OFF
ØIf you wish to cancel the setting and restart, press
e.
+NOTE: You can assign the same Address to the
Keypad and Proximity Reader as these devices
are intrinsically different.
5.Press Eto confirm the selected Address:
Øafter several seconds the Keypad will emit an audi-
ble signal, and the 4 LEDs on the right (see 89b in
Figure 8) will turn ON to indicate access to the Ad-
dressing phase of the built-in Proximity Reader.
ØIf you DO NOT wish to use the Proximity Reader,
press o. The ALISON/32LP will go back automati-
cally to the Keypad Addressing phase, at which
point,gotostep8. in this section.
ØIfyouwishtousetheProximity Reader,gotostep6.
6.Following the instructions in step 4., assign an Ad-
dress to the Reader.
ØIf you wish to cancel the setting and restart, press
e.
+NOTE: If you press eat this point, the
ALISON/32LP will cancel the setting and step back
to the Keypad Addressing phase.
7.Once you have assigned the Keypad and Reader
Addresses, press E.
8. Reinsert the Jumper 73 immediately, in accordance
with the selected BPI Level (refer to “Setting up the BPI
Level”), then replace the frontplate.
ALISON-DVP ASSIGNING ADDRESSES On first
power up the Keypad will assume the preset Address
‘01’ (at default):
NOTE: If the buzzer volume is set at 0, the keypad will
be unable to emit audible signals (refer to ‘ADJUSTING
THE ON-BOARD BUZZER VOLUME’).
Work carefully through the following steps.
1. Generate Tamper status by removing the case.
2. Connect the Keypad to the Control panel BPI BUS.
3. Remove the Jumper 73 — after several seconds the
Keypad will emit an audible signal (long beep) to indi-
cate access to the programming phase.
4.Using keys Aor B, select the required operating mode:
If you intend using the Keypad with a Control panel:
— select “ALISON/DVP”, then press Eto confirm.
On first power-up the display will show:
“ALISON/DVP”.
20
No. ADDRESS COMBINATIONS
1234567891011121314151617181920212223242526272829303132
1(0) off off off off off off off off off off off off off off off off ONONONONONONONONONONONONONONONON
2(1) off off off off off off off off ONONONONONONONON off off off off off off off off ONONONONONONONON
3(2) off off off off ONONONON off off off off ONONONON off off off off ONONONON off off off off ONONONON
4(3) off off ONON off off ONON off off ONON off off ONON off off ONON off off ONON off off ONON off off ONON
5(4) off ON off ON off ON off ON off ON off ON off ON off ON off ON off ON off ON off ON off ON off ON off ON off ON
Table 1 Expander Module and Power Station Addresses. The No. column shows the DIP switch number (1 through 5
for devices with 5 DIP switches, and 1 through 4 in brackets for devices with 4 DIP switches).